Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2321  Driver Side Door ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (main body ECU) stops for 10 seconds or more.

*1: for LHD

*2: for RHD


DTC Code DTC Detection Condition Trouble Area
B2321 No communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (main body ECU) for 10 seconds or more.
·

Front power window regulator motor assembly LH*1

·

Front power window regulator motor assembly RH*2

·

Main body ECU (main body ECU)

·

Harness or connector



*1: for LHD

*2: for RHD


WIRING DIAGRAM

E349669E01
0.135,2.948 0.917,3.167 0.781,0.219 10 false *1: for LHD 0.135,3.344 0.938,3.583 0.802,0.24 10 false *2: for RHD 1.469,0.677 1.833,0.896 0.365,0.219 10 false LIN2 1.906,0.531 2.219,0.729 0.313,0.198 10 false 16 0.875,1.25 1.656,1.458 0.781,0.208 10 false K4*1, J9*2 0.885,1.438 2.479,1.802 1.594,0.365 10 false Multiplex Network Master Switch Assembly 2.813,1.219 3.677,1.448 0.865,0.229 10 false from Battery 4.26,1.417 4.927,1.646 0.667,0.229 10 false DOOR D 4.719,2.417 5.458,2.615 0.74,0.198 10 false K7*1, J7*2 4.719,2.625 6.667,2.99 1.948,0.365 10 false Front Power Window Regulator Motor Assembly LH*1, RH*2 5.115,0.552 5.271,0.75 0.156,0.198 10 false 9 5.104,1.094 5.26,1.292 0.156,0.198 10 false 2 5.115,1.635 5.271,1.833 0.156,0.198 10 false 1 5.375,0.688 5.833,0.885 0.458,0.198 10 false LIN 5.365,1.24 5.521,1.438 0.156,0.198 10 false B 5.375,1.771 5.833,1.969 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:
·

When communication between the front power window regulator motor assembly LH*1 or RH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.

·

When DTC B1206 and B2321 are output simultaneously, perform troubleshooting for DTC B1206 first.



*1: for LHD

*2: for RHD


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2321 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)
3.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the K4*1 or J9*2 multiplex network master switch assembly connector.


b.

Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K4-16 (LIN2) - K7-9 (LIN) Always Below 1 Ω
K4-16 (LIN2) or K7-9 (LIN) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
J9-16 (LIN2) - J7-9 (LIN) Always Below 1 Ω
J9-16 (LIN2) or J7-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)
a.
U170165E02
1.594,1 1.167,0.323 1.167,0.323 1.031,0.323 true 1.844,1.021 2.25,0.313 2.25,0.313 2.385,0.313 true 0.052,0.042 0.229,0.24 0.177,0.198 10 false *a 2.49,0.24 2.635,0.417 0.146,0.177 10 false B 0.646,0.24 0.979,0.417 0.333,0.177 10 false GND 0.635,0.896 0.875,1.073 0.24,0.177 10 false K7 0.656,1.281 0.896,1.458 0.24,0.177 10 false J7 1.052,0.885 1.292,1.063 0.24,0.177 10 false *A 1.052,1.292 1.292,1.469 0.24,0.177 10 false *B

Disconnect the K7*1 or J7*2 front power window regulator motor assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K7-1 (GND) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
J7-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Condition Specified Condition
K7-2 (B) - Body ground Always 11 to 14 V

for RHD:
Tester Connection Condition Specified Condition
J7-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly)


OK

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY
a.

Temporarily replace the front power window regulator motor assembly LH*1 or RH*2 with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).

*1: for LHD

*2: for RHD




NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2321 is not output.




OK

END (FRONT POWER WINDOW REGULATOR MOTOR IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)