This DTC is stored when LIN communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
*1: for LHD
*2: for RHD
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2322 | No communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Front power window regulator motor assembly RH*1 ·
Front power window regulator motor assembly LH*2 ·
Main body ECU (multiplex network body ECU) ·
Harness or connector |
*1: for LHD
*2: for RHD
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.
Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.
When communication between the front power window regulator motor assembly RH*1 or LH*2 and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.
*1: for LHD
*2: for RHD
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
DTC B2322 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - J7-9 (LIN) | Always | Below 1 Ω |
| A-16 (LIN2) or J7-9 (LIN) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-16 (LIN2) - K7-9 (LIN) | Always | Below 1 Ω |
| A-16 (LIN2) or K7-9 (LIN) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the J7*1 or K7*2 front power window regulator motor assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-1 (GND) - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-1 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J7-2 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K7-2 (B) - Body ground | Always | 11 to 14 V |
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Front Power Window Regulator Motor Assembly) |
OK
NG
Temporarily replace the front power window regulator motor assembly RH*1 or LH*2 with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Front Door)>REMOVAL).
*1: for LHD
*2: for RHD
NEXT
Clear the DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
NEXT
Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).
DTC B2322 is not output.
OK
NG