Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261030 LIN COMMUNICATION SYSTEM C

NETWORKING  LIN COMMUNICATION SYSTEM  B2323  Rear Door RH ECU Communication Stop  


DESCRIPTION

This DTC is stored when LIN communication between the rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2323 No communication between the rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) for 10 seconds or more.
·

Rear power window regulator motor assembly RH

·

Main body ECU (multiplex network body ECU)

·

Harness or connector



WIRING DIAGRAM

E349669E03
1.469,0.677 1.833,0.896 0.365,0.219 10 false LIN2 1.906,0.531 2.219,0.729 0.313,0.198 10 false 16 0.875,1.25 1.656,1.458 0.781,0.208 10 false A 0.854,1.438 2.49,1.813 1.635,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.813,1.219 3.677,1.448 0.865,0.229 10 false from Battery 4.26,1.417 4.927,1.646 0.667,0.229 10 false DOOR RR 4.719,2.417 5.458,2.615 0.74,0.198 10 false L4 4.719,2.625 6.583,3.01 1.865,0.385 10 false Rear Power Window Regulator Motor Assembly RH 5.115,0.552 5.271,0.75 0.156,0.198 10 false 9 5.104,1.094 5.26,1.292 0.156,0.198 10 false 2 5.115,1.635 5.271,1.833 0.156,0.198 10 false 1 5.375,0.688 5.833,0.885 0.458,0.198 10 false LIN 5.365,1.24 5.521,1.438 0.156,0.198 10 false B 5.375,1.771 5.833,1.969 0.458,0.198 10 false GND

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the ignition switch off to troubleshoot:

Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Inspect the fuses and bulbs for circuits related to this system before performing the following inspection procedure.



HINT:

When communication between the rear power window regulator motor assembly RH and main body ECU (multiplex network body ECU) stops, DTC B2325 is also stored.


PROCEDURE

1.CLEAR DTC

NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2323 is not output.




OK

NG

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR RH)
3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - REAR POWER WINDOW REGULATOR MOTOR RH)
a.

Remove the main body ECU (multiplex network body ECU) from the driver side junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Disconnect the L4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-16 (LIN2) - L4-9 (LIN) Always Below 1 Ω
A-16 (LIN2) or L4-9 (LIN) - Body ground Always 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR RH - BATTERY AND BODY GROUND)
a.
U116059E04
1.552,1 1.229,0.354 1.229,0.354 1.094,0.354 true 1.854,0.99 2.219,0.344 2.219,0.344 2.354,0.344 true 0.063,0.031 0.24,0.229 0.177,0.198 10 false *a 2.448,0.271 2.594,0.448 0.146,0.177 10 false B 0.75,0.281 1.083,0.458 0.333,0.177 10 false GND 0.844,1.094 1.083,1.271 0.24,0.177 10 false L4

Disconnect the L4 rear power window regulator motor assembly RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L4-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L4-2 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Rear Power Window Regulator Motor Assembly RH)


OK

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Temporarily replace the rear power window regulator motor assembly RH with a new or normally functioning one (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).



NEXT

6.CLEAR DTC
6.CLEAR DTC

NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs (See page Power Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2323 is not output.




OK

END (REAR POWER WINDOW REGULATOR MOTOR RH IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)