Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261031 CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD with Entry and Start System)  Check Sub Bus Wire Harness  


DESCRIPTION

Symptom Trouble Area
All DTCs related to the sub bus are output from the ECM.
·

Local bus circuit

·

ECM

·

Urea pump control ECU

·

Nitrogen oxides sensor

·

No. 9 junction connector



WIRING DIAGRAM

C329276E06
5.896,1.781 6.406,2.083 0.51,0.302 10 false G184 5.906,1.938 6.333,2.219 0.427,0.281 10 false ECM 5.667,0.896 6.073,1.125 0.406,0.229 10 false CANU 5.677,1.521 6.083,1.75 0.406,0.229 10 false CAND 5.438,1.313 5.844,1.542 0.406,0.229 10 false 35 5.427,0.917 5.833,1.146 0.406,0.229 10 false 27 4.042,0.917 4.448,1.146 0.406,0.229 10 false 5 4.042,1.313 4.448,1.542 0.406,0.229 10 false 16 3.083,1.313 3.49,1.542 0.406,0.229 10 false 17 3.167,0.906 3.573,1.135 0.406,0.229 10 false 6 1.24,1.406 1.646,1.635 0.406,0.229 10 false CAN- 1.25,0.99 1.656,1.219 0.406,0.229 10 false CAN+ 1.281,2.875 1.688,3.104 0.406,0.229 10 false CAN+ 1.708,2.885 2.115,3.115 0.406,0.229 10 false 27 1.708,3.313 2.115,3.542 0.406,0.229 10 false 26 1.24,3.531 1.646,3.76 0.406,0.229 10 false CAN- 3.167,2.875 3.573,3.104 0.406,0.229 10 false 4 3.104,3.323 3.51,3.552 0.406,0.229 10 false 15 1.719,0.875 2.125,1.104 0.406,0.229 10 false 4 1.729,1.292 2.135,1.521 0.406,0.229 10 false 3 0.552,3.802 1.99,4.146 1.438,0.344 10 false s4 0.552,1.771 2.469,2.094 1.917,0.323 10 false s6 0.552,1.938 2.469,2.26 1.917,0.323 10 false Nitrogen Oxides Sensor 0.552,3.938 2.156,4.271 1.604,0.333 10 false Urea Pump Control ECU 3.021,3.792 4.458,4.135 1.438,0.344 10 false Q41 3.01,3.938 4.885,4.323 1.875,0.385 10 false No. 9 Junction Connector

CAUTION / NOTICE / HINT

HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.

Measure the resistance according to the value(s) in the table below.

U170470E01
6.674,1.76 6.733,1.76 6.733,1.76 6.866,1.043 false 4.012,1.76 4.071,1.76 4.071,1.76 4.59,1.043 false 4.03,0.346 4.415,0.524 0.385,0.178 10 C152 5.123,0.346 5.501,0.524 0.378,0.178 10 G184 6.23,0.346 6.601,0.524 0.371,0.178 10 G185 3.779,2.025 4.339,2.203 0.560,0.178 10 CANU 3.964,2.333 4.528,2.511 0.564,0.178 10 CAND 6.289,1.689 6.703,1.867 0.413,0.178 10 BATT 3.742,1.708 3.995,1.878 0.253,0.170 10 E1 4.4,2.403 4.459,2.403 4.459,2.403 4.786,1.401 false 4.212,2.095 4.272,2.095 4.272,2.095 4.776,1.279 false

Text in Illustration
*a Component with harness connected
(ECM)
- -

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G184-27 (CANU) - G184-35 (CAND) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G184-27 (CANU) - G184-35 (CAND) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G184-27 (CANU) - G185-1 (BATT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G184-35 (CAND) - G185-1 (BATT) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G184-27 (CANU) - C152-1 (E1) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G184-35 (CAND) - C152-1 (E1) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - UREA PUMP CONTROL ECU)

B

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NITROGEN OXIDES SENSOR)

C

18.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - UREA PUMP CONTROL ECU)
a.

Disconnect the No. 9 junction connector.


U170107E02
1.969,0.979 1,0.521 1,0.521 0.917,0.521 false 1.969,1.156 1,1.563 1,1.563 0.917,1.563 false 0.396,0.438 0.833,0.615 0.438,0.177 10 false CANH 0.49,0.854 0.813,1.031 0.323,0.177 10 false Q41 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a 0.469,1.469 0.906,1.646 0.438,0.177 10 false CANL

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q41-4 (CANH) - Q41-15 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - ECM)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - ECM)
a.
U170108E02
1.844,0.979 1,0.521 1,0.521 0.917,0.521 false 1.844,1.177 0.99,1.583 0.99,1.583 0.906,1.583 false 0.49,0.438 0.927,0.615 0.438,0.177 10 false CANH 0.49,0.813 0.813,0.99 0.323,0.177 10 false Q41 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a 0.51,1.51 0.948,1.688 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q41-5 (CANH) - Q41-16 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the Q41 No. 9 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (UREA PUMP CONTROL ECU - NO. 9 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (UREA PUMP CONTROL ECU - NO. 9 JUNCTION CONNECTOR)
a.
U170262E02
2.271,1.01 2.51,0.219 2.51,0.219 2.552,0.219 false 2.167,1.042 2.448,1.969 2.448,1.969 2.49,1.969 false 0.302,1.083 0.573,1.229 0.271,0.146 10 false s4 0.063,0.042 0.323,0.188 0.26,0.146 10 false *a 2.615,0.146 3.021,0.292 0.406,0.146 10 false CAN+ 2.552,1.885 2.958,2.031 0.406,0.146 10 false CAN-

Disconnect the urea pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
s4-27 (CAN+) - s4-26 (CAN-) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Urea Pump Control ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO UREA PUMP CONTROL ECU (UREA PUMP CONTROL ECU - NO. 9 JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the Q41 No. 9 junction connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 9 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 9 JUNCTION CONNECTOR)
a.
U170471E03
2.448,2.094 2.49,2.823 2.49,2.823 2.583,2.823 false 2.448,1.833 2.604,0.781 2.604,0.781 2.698,0.781 false 1.49,0.313 1.885,0.49 0.396,0.177 10 false G184 2.635,2.75 3.115,2.927 0.479,0.177 10 false CAND 2.75,0.698 3.229,0.875 0.479,0.177 10 false CANU 0.135,0.083 0.615,0.26 0.479,0.177 10 false *a

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 9 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NITROGEN OXIDES SENSOR)
a.
U170406E03
1.729,1.156 2.5,0.865 2.5,0.865 2.719,0.865 false 1.74,1.365 2.531,1.74 2.531,1.74 2.667,1.74 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.625,2.51 1.51,2.188 1.51,2.188 1.396,2.188 false 0.385,0.99 0.667,1.167 0.281,0.177 10 false Q41 2.781,0.792 3.188,0.969 0.406,0.177 10 false CANH 2.719,1.667 3.104,1.844 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.146,2.104 1.375,2.281 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Disconnect the No. 9 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q41-6 (CANH) - Q41-17 (CANL) Engine switch off 200 Ω or higher
Q41-6 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-17 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-6 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
Q41-17 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - UREA PUMP CONTROL ECU)

NG

12.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - UREA PUMP CONTROL ECU)
a.
U170407E02
1.969,1.146 2.521,0.854 2.521,0.854 2.74,0.854 false 1.969,1.365 2.552,1.719 2.552,1.719 2.688,1.719 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.635,2.552 1.542,2.146 1.542,2.146 1.427,2.146 false 0.396,0.979 0.677,1.156 0.281,0.177 10 false Q41 2.792,0.781 3.198,0.958 0.406,0.177 10 false CANH 2.719,1.635 3.104,1.813 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.052 1.365,2.229 0.229,0.177 10 false CG 0.406,2.688 0.688,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q41-4 (CANH) - Q41-15 (CANL) Engine switch off 108 to 132 Ω
Q41-4 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-15 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-4 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
Q41-15 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - ECM)

NG

14.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - ECM)
a.
U170408E02
1.844,1.146 2.521,0.854 2.521,0.854 2.74,0.854 false 1.844,1.365 2.552,1.719 2.552,1.719 2.688,1.719 false 2.208,2.927 2.292,3.135 2.292,3.135 2.417,3.135 false 1.635,2.552 1.542,2.146 1.542,2.146 1.427,2.146 false 0.396,0.99 0.677,1.167 0.281,0.177 10 false Q41 2.781,0.781 3.188,0.958 0.406,0.177 10 false CANH 2.719,1.646 3.104,1.823 0.385,0.177 10 false CANL 2.458,3.063 2.75,3.24 0.292,0.177 10 false BAT 1.135,2.052 1.365,2.229 0.229,0.177 10 false CG 0.396,2.688 0.677,2.865 0.281,0.177 10 false G48 0.208,1.969 0.365,2.146 0.156,0.177 10 false *b 0.156,0.052 0.313,0.229 0.156,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
Q41-5 (CANH) - Q41-16 (CANL) Engine switch off 108 to 132 Ω
Q41-5 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-16 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
Q41-5 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
Q41-16 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 9 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 9 JUNCTION CONNECTOR

NG

16.CONNECT CONNECTOR
12.CONNECT CONNECTOR
a.

Reconnect the Q41 No. 9 junction connector.



NEXT

13.CHECK FOR SHORT IN CAN BUS WIRES (NITROGEN OXIDES SENSOR)
13.CHECK FOR SHORT IN CAN BUS WIRES (NITROGEN OXIDES SENSOR)
a.
U170311E02
2.49,0.427 2.396,0.427 2.396,0.427 1.99,0.958 false 2.26,2.76 2.479,2.906 2.479,2.906 2.573,2.906 false 1.656,2.323 1.375,1.938 1.375,1.938 1.25,1.938 false 1.677,0.958 1.073,0.438 1.073,0.438 0.948,0.438 false 1.656,0.188 1.969,0.365 0.313,0.177 10 false s6 1.604,1.729 1.917,1.906 0.313,0.177 10 false G48 2.635,2.823 2.979,3 0.344,0.177 10 false BAT 0.5,0.333 1.063,0.51 0.563,0.177 10 false CAN- 2.531,0.344 2.979,0.521 0.448,0.177 10 false CAN+ 0.885,1.854 1.156,2.031 0.271,0.177 10 false CG 0.094,0.073 0.656,0.25 0.563,0.177 10 false *a 0.073,1.615 0.635,1.792 0.563,0.177 10 false *b

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
s6-4 (CAN+) - s6-3 (CAN-) Engine switch off 54 to 69 Ω
s6-4 (CAN+) - G48-4 (CG) Engine switch off 200 Ω or higher
s6-3 (CAN-) - G48-4 (CG) Engine switch off 200 Ω or higher
s6-4 (CAN+) - G48-16 (BAT) Engine switch off 6 kΩ or higher
s6-3 (CAN-) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NITROGEN OXIDES SENSOR (CAN+, CAN-)

14.CONNECT CONNECTOR
a.

Reconnect the Q41 No. 9 junction connector.



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (UREA PUMP CONTROL ECU)
15.CHECK FOR SHORT IN CAN BUS WIRES (UREA PUMP CONTROL ECU)
a.
U170263E02
2.198,2.906 2.354,3.177 2.354,3.177 2.469,3.177 false 2.167,1 2.583,0.375 2.583,0.375 2.698,0.375 true 2.073,1 1.375,0.323 1.375,0.323 1.26,0.323 true 1.646,2.479 1.292,2.125 1.292,2.125 1.177,2.125 false 0.083,0.052 0.375,0.208 0.292,0.156 10 false *a 0.083,1.896 0.375,2.052 0.292,0.156 10 false *b 0.323,1.01 0.594,1.146 0.271,0.135 10 false s4 0.385,2.625 0.708,2.76 0.323,0.135 10 false G48 2.479,3.104 2.771,3.25 0.292,0.146 10 false BAT 2.74,0.302 3.229,0.448 0.49,0.146 10 false CAN+ 0.865,0.24 1.354,0.385 0.49,0.146 10 false CAN- 0.854,2.042 1.135,2.188 0.281,0.146 10 false CG

Disconnect the urea pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
s4-27 (CAN+) - s4-26 (CAN-) Engine switch off 108 to 132 Ω
s4-27 (CAN+) - G48-4 (CG) Engine switch off 200 Ω or higher
s4-26 (CAN-) - G48-4 (CG) Engine switch off 200 Ω or higher
s4-27 (CAN+) - G48-16 (BAT) Engine switch off 6 kΩ or higher
s4-26 (CAN-) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Urea Pump Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO UREA PUMP CONTROL ECU (CAN+, CAN-)

16.CONNECT CONNECTOR
a.

Reconnect the Q41 No. 9 junction connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
17.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170475E02
1.646,3.313 0.958,2.927 0.958,2.927 0.844,2.927 false 2.448,1.979 2.656,2.479 2.656,2.479 2.75,2.479 false 2.354,3.813 2.594,4.177 2.594,4.177 2.719,4.177 false 2.448,1.729 2.594,0.656 2.594,0.656 2.677,0.656 false 1.552,0.406 1.948,0.583 0.396,0.177 10 false G184 1.604,2.74 1.917,2.917 0.313,0.177 10 false G48 0.594,2.854 0.906,3.031 0.313,0.177 10 false CG 2.802,2.406 3.25,2.583 0.448,0.177 10 false CAND 2.729,0.583 3.208,0.76 0.479,0.177 10 false CANU 2.74,4.083 3.083,4.25 0.344,0.167 10 false BAT 0.094,0.167 0.656,0.344 0.563,0.177 10 false *a 0.094,2.573 0.656,2.75 0.563,0.177 10 false *b

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Engine switch off 108 to 132 Ω
G184-27 (CANU) - G48-4 (CG) Engine switch off 200 Ω or higher
G184-35 (CAND) - G48-4 (CG) Engine switch off 200 Ω or higher
G184-27 (CANU) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G184-35 (CAND) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANU, CAND)

18.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND GROUND)
a.

Connect the cable to the negative (-) battery terminal.

U170474E03
6.219,3.208 6.146,3.208 6.146,3.208 5.427,2.656 false 2.271,2.813 2.635,2.083 2.635,2.083 2.719,2.083 false 6.146,1.969 6.083,1.969 6.083,1.969 5.271,2.604 false 1.76,0.875 0.969,0.458 0.969,0.458 0.854,0.458 false 4.906,2.813 4.406,3.208 4.406,3.208 4.271,3.208 false 4.917,2.594 4.438,2.26 4.438,2.26 4.302,2.26 false 5.073,2.573 4.469,1.938 4.469,1.938 4.323,1.938 false 4.875,0.885 4.51,0.531 4.51,0.531 4.365,0.531 false 5.177,0.865 4.573,0.25 4.573,0.25 4.438,0.25 false 5.396,0.875 6.135,0.25 6.135,0.25 6.198,0.25 false 1.76,0.198 2.146,0.375 0.385,0.177 10 false C151 6.25,0.188 6.854,0.365 0.604,0.177 10 false E02 2.76,2.01 3.323,2.188 0.563,0.177 10 false MREL 4.042,0.188 4.49,0.365 0.448,0.177 10 false ME01 4.167,0.469 4.438,0.646 0.271,0.177 10 false E1 0.552,0.385 0.917,0.563 0.365,0.177 10 false E01 4.115,1.865 4.677,2.031 0.563,0.167 10 false +B 1.76,1.979 2.146,2.156 0.385,0.177 10 false G184 5.219,0.208 5.604,0.385 0.385,0.177 10 false C152 5.271,1.917 5.656,2.094 0.385,0.177 10 false G185 6.198,1.906 6.76,2.073 0.563,0.167 10 false +B2 6.25,3.135 6.813,3.302 0.563,0.167 10 false +B3 3.917,2.188 4.479,2.354 0.563,0.167 10 false BATT 4.021,3.146 4.583,3.313 0.563,0.167 10 false EC 0.125,0.094 0.49,0.271 0.365,0.177 10 false *a

Text in Illustration
*a Front view of wire harness connector
(to ECM)
- -

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C152-1 (E1) - Body ground Always Below 1 Ω
C151-3 (E01) - Body ground Always Below 1 Ω
C152-4 (E02) - Body ground Always Below 1 Ω
C152-3 (ME01) - Body ground Always Below 1 Ω
G185-8 (EC) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G185-1 (BATT) - Body ground Always 11 to 14 V
G185-2 (+B) - Body ground Battery positive (+) voltage applied to terminal G184-14 (MREL) 11 to 14 V
G185-3 (+B2) - Body ground Battery positive (+) voltage applied to terminal G184-14 (MREL) 11 to 14 V
G185-4 (+B3) - Body ground Battery positive (+) voltage applied to terminal G184-14 (MREL) 11 to 14 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR