Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  U1002  Lost Communication with Gateway Module (MS Bus)  


DESCRIPTION

·

The main body ECU (multiplex network body ECU) stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.

·

When the main body ECU (multiplex network body ECU) receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU (multiplex network body ECU) recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU (multiplex network body ECU) monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU (multiplex network body ECU) cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU (multiplex network body ECU) determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module.
·

MS bus circuit

·

Main body ECU (multiplex network body ECU) CAN main wire or connector

·

Driving support switch control ECU CAN branch wire or connector

·

Main body ECU (multiplex network body ECU)

·

Driving support switch control ECU

·

No. 3 junction connector

·

No. 8 junction connector



For vehicles with a multi-function switch.


WIRING DIAGRAM

C294453E02
5.354,0.969 5.563,1.156 0.208,0.188 10 false 10 5.438,0.438 5.604,0.635 0.167,0.198 10 false 9 5.438,2.292 5.573,2.479 0.135,0.188 10 false 3 5.438,2.833 5.594,3.031 0.156,0.198 10 false 2 3.99,0.958 4.24,1.156 0.25,0.198 10 false 15 3.99,0.448 4.125,0.625 0.135,0.177 10 false 4 3.156,0.938 3.365,1.115 0.208,0.177 10 false 16 3.219,0.438 3.396,0.646 0.177,0.208 10 false 5 4.021,2.302 4.229,2.521 0.208,0.219 10 false 6 3.99,2.813 4.25,3.031 0.26,0.219 10 false 17 5.635,0.427 6.219,0.604 0.583,0.177 10 false CANP 5.635,1.177 6.208,1.354 0.573,0.177 10 false CANN 5.635,2.313 6.219,2.521 0.583,0.208 10 false CANP 5.635,3.042 6.156,3.219 0.521,0.177 10 false CANN 1.396,0.552 1.854,0.781 0.458,0.229 10 false CANP 1.396,1.063 1.896,1.313 0.5,0.25 10 false CANN 1.927,0.563 2.375,0.76 0.448,0.198 10 false G163 1.979,0.354 2.302,0.563 0.323,0.208 10 false 2*1 1.927,1.083 2.354,1.292 0.427,0.208 10 false G163 1.99,0.854 2.25,1.052 0.26,0.198 10 false 3*1 2.396,1.083 2.729,1.26 0.333,0.177 10 false G76 2.375,0.865 2.75,1.063 0.375,0.198 10 false 10*2 2.396,0.563 2.729,0.771 0.333,0.208 10 false G76 2.417,0.333 2.74,0.542 0.323,0.208 10 false 9*2 0.708,1.469 2.479,2.24 1.771,0.771 10 false Driving Support Switch Control ECU 0.229,2.802 2.604,2.979 2.375,0.177 10 false *1: for Automatic Transmission 0.229,3.125 2.604,3.302 2.375,0.177 10 false *2: for Manual Transmission 5.177,3.198 6.792,3.344 1.615,0.146 10 false G103 5.198,3.354 6.865,3.677 1.667,0.323 10 false No. 8 Junction Connector 2.906,3.146 4.521,3.292 1.615,0.146 10 false G96 2.906,3.302 4.573,3.625 1.667,0.323 10 false No. 3 Junction Connector 5.208,1.292 6.875,2.063 1.667,0.771 10 false G63 5.208,1.438 6.875,2.208 1.667,0.771 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U170148E02
1.729,0.896 1.51,0.26 1.51,0.26 1.323,0.26 false 1.448,0.896 1.26,0.604 1.26,0.604 1.094,0.604 false 2.146,2.781 2.354,3.01 2.354,3.01 2.458,3.01 false 1.688,2.458 1.5,2.177 1.5,2.177 1.396,2.177 false 0.104,1.958 0.323,2.156 0.219,0.198 10 false *b 0.104,0.073 0.323,0.271 0.219,0.198 10 false *a 0.885,0.177 1.354,0.375 0.469,0.198 10 false CANN 0.667,0.531 1.167,0.729 0.5,0.198 10 false CANP 2.521,2.938 2.833,3.135 0.313,0.198 10 false BAT 0.531,2.573 0.875,2.74 0.344,0.167 10 false G48 0.448,0.969 0.844,1.177 0.396,0.208 10 false G103 1.146,2.094 1.396,2.292 0.25,0.198 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G103-3 (CANP) - G103-2 (CANN) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
G103-3 (CANP) - G103-2 (CANN) Ignition switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G103-3 (CANP) - G48-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
G103-2 (CANN) - G48-16 (BAT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
G103-3 (CANP) - G48-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
G103-2 (CANN) - G48-4 (CG) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(No. 8 Junction Connector)
*b Front view of DLC3

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

GND short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

B

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)

C

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.

Disconnect the G96 No. 3 junction connector.


U170380E01
2.482,0.838 2.381,0.838 2.381,0.838 1.976,1.234 false 1.976,1.439 2.285,1.85 2.285,1.85 2.408,1.85 false 2.5,0.761 2.920,0.898 0.421,0.137 10 CANH 2.419,1.768 2.815,1.905 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.413,1.259 0.694,1.396 0.281,0.137 10 G96

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-4 (CANH) - G96-15 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)
a.
U170381E01
1.174,0.551 1.275,0.551 1.275,0.551 1.727,1.234 false 1.727,1.439 1.418,1.902 1.418,1.902 1.296,1.902 false 0.66,0.473 1.081,0.610 0.421,0.137 10 CANH 0.82,1.82 1.217,1.957 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 2.618,1.259 2.898,1.396 0.281,0.137 10 G96

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-6 (CANH) - G96-17 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU)
a.
U170149E02
1.958,0.219 1.813,0.219 1.813,0.219 1.479,1.188 false 2.26,0.479 2.104,0.479 2.104,0.479 1.583,1.188 false 2.01,0.135 2.646,0.385 0.635,0.25 10 false CANP 0.25,1.156 0.552,1.333 0.302,0.177 10 false G63 0.073,0 0.281,0.177 0.208,0.177 10 false *a 2.292,0.406 2.76,0.646 0.469,0.24 10 false CANN

Disconnect the G63 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 3 JUNCTION JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR)
a.
U170276E02
1.313,0.802 1.052,0.552 1.052,0.552 0.927,0.552 false 1.24,0.24 1.365,0.24 1.365,0.24 1.646,0.802 false 0.51,0.479 1.104,0.677 0.594,0.198 10 false CANP 0.813,0.167 1.417,0.365 0.604,0.198 10 false CANN 0.063,0 0.615,0.135 0.552,0.135 10 false *a 0.344,0.896 0.76,1.125 0.417,0.229 10 false G103

Disconnect the G103 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G103-3 (CANP) - G103-2 (CANN) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - DRIVING SUPPORT SWITCH CONTROL ECU)
a.
U170392E01
1.666,2.523 1.387,2.164 1.387,2.164 1.29,2.164 false 2.206,2.959 2.344,3.208 2.344,3.208 2.484,3.208 false 1.829,1.291 2.108,1.649 2.108,1.649 2.205,1.649 false 2.371,0.723 2.257,0.723 2.257,0.723 1.829,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.393,0.645 2.813,0.787 0.420,0.142 10 CANH 2.223,1.564 2.647,1.706 0.424,0.142 10 CANL 2.519,3.123 2.943,3.265 0.424,0.142 10 BAT 0.98,2.074 1.404,2.216 0.424,0.142 10 CG 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.427,1.094 0.708,1.232 0.281,0.138 10 G96

Disconnect the G96 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-5 (CANH) - G96-16 (CANL) Ignition switch off 200 Ω or higher
G96-5 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-16 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-5 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G96-16 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

NG

12.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)
a.
U170393E01
1.666,2.523 1.387,2.164 1.387,2.164 1.29,2.164 false 2.206,2.959 2.344,3.208 2.344,3.208 2.484,3.208 false 1.915,1.291 2.129,1.628 2.129,1.628 2.227,1.628 false 2.371,0.723 2.257,0.723 2.257,0.723 1.915,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.393,0.645 2.813,0.787 0.420,0.142 10 CANH 2.244,1.542 2.668,1.684 0.424,0.142 10 CANL 2.519,3.123 2.943,3.265 0.424,0.142 10 BAT 0.98,2.074 1.404,2.216 0.424,0.142 10 CG 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 0.427,1.094 0.708,1.232 0.281,0.138 10 G96

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-4 (CANH) - G96-15 (CANL) Ignition switch off 108 to 132 Ω
G96-4 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-15 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-4 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G96-15 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)

NG

14.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)
a.
U170394E01
1.666,2.523 1.387,2.164 1.387,2.164 1.29,2.164 false 2.206,2.959 2.344,3.208 2.344,3.208 2.484,3.208 false 1.721,1.291 1.442,1.649 1.442,1.649 1.345,1.649 false 1.087,0.638 1.202,0.638 1.202,0.638 1.721,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.566,0.56 0.986,0.702 0.420,0.142 10 CANH 0.854,1.564 1.277,1.706 0.424,0.142 10 CANL 2.519,3.123 2.943,3.265 0.424,0.142 10 BAT 0.98,2.074 1.404,2.216 0.424,0.142 10 CG 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 2.547,1.094 2.828,1.232 0.281,0.138 10 G96

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G96-6 (CANH) - G96-17 (CANL) Ignition switch off 108 to 132 Ω
G96-6 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-17 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G96-6 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G96-17 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

16.CONNECT CONNECTOR
12.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

13.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)
13.CHECK FOR SHORT IN CAN BUS WIRES (DRIVING SUPPORT SWITCH CONTROL ECU)
a.

for Automatic Transmission:

i.
U148940E03
1.333,2.073 1.438,2.073 1.438,2.073 1.677,2.5 false 2.563,3.156 2.458,3.156 2.458,3.156 2.333,2.927 false 1.427,1.083 1.094,0.802 1.094,0.802 0.979,0.802 false 1.563,1.073 1.271,0.479 1.271,0.479 1.146,0.479 false 0.063,0.01 0.24,0.177 0.177,0.167 10 false *a 0.063,1.719 0.24,1.885 0.177,0.167 10 false *b 1.083,1.99 1.344,2.146 0.26,0.156 10 false CG 2.594,3.073 2.938,3.229 0.344,0.156 10 false BAT 0.729,0.406 1.24,0.604 0.51,0.198 10 false CANN 0.563,0.729 1.073,0.938 0.51,0.208 10 false CANP 2.604,1.146 3.042,1.344 0.438,0.198 10 false G163 0.406,2.625 0.74,2.844 0.333,0.219 10 false G48

Disconnect the G163 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G163-2 (CANP) - G163-3 (CANN) Ignition switch off 54 to 69 Ω
G163-2 (CANP) - G48-4 (CG) Ignition switch off 200 Ω or higher
G163-3 (CANN) - G48-4 (CG) Ignition switch off 200 Ω or higher
G163-2 (CANP) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G163-3 (CANN) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Driving Support Switch Control ECU)
*b Front view of DLC3



b.

for Manual Transmission:

i.
U170151E03
1.385,1.906 1.5,1.906 1.5,1.906 1.844,1.469 false 2.323,1.813 2.208,1.813 2.208,1.813 1.948,1.469 false 2.344,2.927 2.552,3.167 2.552,3.167 2.677,3.167 false 1.688,2.469 1.479,2.146 1.479,2.146 1.354,2.146 false 0.073,0.021 0.271,0.229 0.198,0.208 10 false *a 2.365,1.74 2.792,1.948 0.427,0.208 10 false CANP 0.969,1.823 1.396,2.031 0.427,0.208 10 false CANN 0.448,1.302 0.813,1.521 0.365,0.219 10 false G76 0.083,1.927 0.281,2.094 0.198,0.167 10 false *b 1.125,2.063 1.354,2.24 0.229,0.177 10 false CG 2.719,3.073 3.073,3.25 0.354,0.177 10 false BAT 0.354,2.625 0.719,2.823 0.365,0.198 10 false G48

Disconnect the G76 driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G76-9 (CANP) - G76-10 (CANN) Ignition switch off 54 to 69 Ω
G76-9 (CANP) - G48-4 (CG) Ignition switch off 200 Ω or higher
G76-10 (CANN) - G48-4 (CG) Ignition switch off 200 Ω or higher
G76-9 (CANP) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G76-10 (CANN) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support Switch Control ECU)
*b Front view of DLC3




OK

REPLACE DRIVING SUPPORT SWITCH CONTROL ECU

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DRIVING SUPPORT SWITCH CONTROL ECU (CANP, CANN)

14.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
15.CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)
a.
U170150E02
1.615,1.135 2.052,0.458 2.052,0.458 2.188,0.458 false 1.5,1.135 1.719,0.177 1.719,0.177 1.854,0.177 false 2.344,2.927 2.552,3.094 2.552,3.094 2.708,3.094 false 1.688,2.458 1.354,2.104 1.354,2.104 1.177,2.104 false 2.229,0.385 2.729,0.573 0.5,0.188 10 false CANN 1.885,0.115 2.385,0.313 0.5,0.198 10 false CANP 0.333,1.115 0.708,1.323 0.375,0.208 10 false G63 0.042,2.167 0.25,2.344 0.208,0.177 10 false *b 2.719,3 3.156,3.177 0.438,0.177 10 false BAT 0.042,0.021 0.25,0.198 0.208,0.177 10 false *a 0.927,2.031 1.302,2.26 0.375,0.229 10 false CG 0.385,2.667 0.74,2.875 0.354,0.208 10 false G48

Disconnect the G63 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) Ignition switch off 108 to 132 Ω
G63-9 (CANP) - G48-4 (CG) Ignition switch off 200 Ω or higher
G63-10 (CANN) - G48-4 (CG) Ignition switch off 200 Ω or higher
G63-9 (CANP) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G63-10 (CANN) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of DLC3



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)

16.CONNECT CONNECTOR
a.

Reconnect the G96 No. 3 junction connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR)
17.CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR)
a.
U170305E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.377,0.891 1.161,1.222 1.161,1.222 1.029,1.222 false 1.338,0.314 1.478,0.314 1.478,0.314 1.691,0.708 false 0.08,0.078 0.316,0.314 0.237,0.237 10 *a 0.08,1.909 0.316,2.146 0.237,0.237 10 *b 0.826,0.228 1.247,0.370 0.421,0.142 10 CANN 0.511,1.145 0.934,1.287 0.424,0.142 10 CANP 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.406,2.69 0.692,2.830 0.286,0.140 10 G48 2.538,0.768 2.895,0.908 0.357,0.140 10 G103

Disconnect the G103 No. 8 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G103-3 (CANP) - G103-2 (CANN) Ignition switch off 108 to 132 Ω
G103-3 (CANP) - G48-4 (CG) Ignition switch off 200 Ω or higher
G103-2 (CANN) - G48-4 (CG) Ignition switch off 200 Ω or higher
G103-3 (CANP) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G103-2 (CANN) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 8 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 8 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

18.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


U170059E02
6.25,1.542 6.323,1.542 6.323,1.542 6.51,1.219 false 5.844,0.531 5.906,0.531 5.906,0.531 6.146,1.167 false 3.771,0.531 3.833,0.531 3.833,0.531 4.073,1.167 false 6.417,0.531 6.354,0.531 6.354,0.531 6.26,1.167 false 6.656,0.854 6.583,0.854 6.583,0.854 6.385,1.177 false 0.594,0.563 0.656,0.563 0.656,0.563 0.854,0.927 false 3.365,0.448 3.813,0.615 0.448,0.167 10 false GND1 5.521,0.458 5.875,0.635 0.354,0.177 10 false ACC 6.479,0.448 6.917,0.615 0.438,0.167 10 false BECU 6.073,1.469 6.344,1.667 0.271,0.198 10 false IG 6.708,0.771 7.094,0.938 0.385,0.167 10 false ALTB 2.406,0.021 2.604,0.25 0.198,0.229 10 false *b 0.021,0.021 0.219,0.25 0.198,0.229 10 false *a 0.188,0.5 0.615,0.667 0.427,0.167 10 false GND2 0.177,0.906 0.49,1.073 0.313,0.167 10 false G63 2.427,1.083 2.625,1.271 0.198,0.188 10 false A

Text in Illustration
*a Rear view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])
*b Front view of wire harness connector
(to Main Body ECU [Multiplex Network Body ECU])


b.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-3 (GND2) - Body ground Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A-31 (ALTB) - Body ground Always 11 to 14 V
A-30 (BECU) - Body ground Always 11 to 14 V
A-29 (ACC) - Body ground Ignition switch ACC 11 to 14 V
A-32 (IG) - Body ground Ignition switch ON 11 to 14 V




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR