Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U1002  Lost Communication with Gateway Module (Power Management2)  


DESCRIPTION

·

The power management control ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the power management bus.

·

When the power management control ECU receives a response signal from the ECUs connected to the power management bus, the power management control ECU recognizes and memorizes that the ECU is connected to the power management bus. Based on this memorized data, the power management control ECU monitors for malfunctions in the ECUs connected to the power management bus when communicating with those ECUs. If the power management control ECU cannot receive response signals from the ECUs that have been memorized as those connected to the power management bus, the power management control ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module (Power Management2).
·

Power management bus circuit

·

Air conditioning amplifier assembly CAN branch wire or connector

·

Power management control ECU CAN main wire or connector

·

ECM CAN main wire or connector

·

Air conditioning amplifier assembly

·

Power management control ECU

·

ECM

·

No. 3 junction connector



WIRING DIAGRAM

C215389E17
1.813,2.521 1.99,2.688 0.177,0.167 10 false 21 1.813,2.115 1.99,2.271 0.177,0.156 10 false 20 5.396,2.844 5.719,3.021 0.323,0.177 10 false G51 3,2.813 3.323,2.99 0.323,0.177 10 false G98 3.021,2.979 4.635,3.156 1.615,0.177 10 false No. 3 Junction Connector 1.24,3.167 1.594,3.344 0.354,0.177 10 false ECM 1.344,1.24 1.74,1.417 0.396,0.177 10 false CANL 1.323,0.833 1.75,1.01 0.427,0.177 10 false CANH 1.802,1.073 2.115,1.25 0.313,0.177 10 false 12 1.802,0.656 2.115,0.833 0.313,0.177 10 false 11 0.594,1.604 2.844,1.781 2.25,0.177 10 false Air Conditioning Amplifier Assembly 1.292,2.115 1.729,2.292 0.438,0.177 10 false CANP 5.5,0.677 5.938,0.854 0.438,0.177 10 false CA3P 3.365,2.125 3.469,2.302 0.104,0.177 10 false 9 3.302,2.521 3.479,2.698 0.177,0.177 10 false 20 3.271,0.719 3.458,0.896 0.188,0.177 10 false 10 3.281,1.125 3.458,1.302 0.177,0.177 10 false 21 4.125,0.719 4.323,0.896 0.198,0.177 10 false 11 4.125,1.125 4.302,1.302 0.177,0.177 10 false 22 5.25,0.719 5.427,0.896 0.177,0.177 10 false 12 5.25,1.125 5.427,1.302 0.177,0.177 10 false 11 1.292,2.719 1.729,2.896 0.438,0.177 10 false CANN 5.5,1.354 5.938,1.531 0.438,0.177 10 false CA3N 5.396,3.01 6.688,3.354 1.292,0.344 10 false Power Management Control ECU 1.229,3.01 1.552,3.188 0.323,0.177 10 false G57 0.594,1.458 0.917,1.635 0.323,0.177 10 false G25

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U148248E03
2.208,1.052 2.552,0.583 2.552,0.583 2.698,0.583 false 1.635,1 1.448,0.552 1.448,0.552 1.354,0.552 true 2.135,1.104 2.344,0.427 2.344,0.427 2.479,0.427 true 2.521,1.01 2.833,1.167 2.833,1.167 2.865,1.167 true 0.042,0 0.219,0.167 0.177,0.167 10 false *a 1.917,0.083 2.208,0.25 0.292,0.167 10 false G51 2.906,1.094 3.302,1.26 0.396,0.167 10 false AM22 1.042,0.469 1.385,0.635 0.344,0.167 10 false GND 2.74,0.5 3.198,0.677 0.458,0.177 10 false CA3N 2.521,0.344 3.031,0.521 0.51,0.177 10 false CA3P

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Below 53 Ω: Short in line
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G51-12 (CA3P) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-11 (CA3N) - G51-1 (AM22) Engine switch off 6 kΩ or higher Below 6 kΩ: +B short
G51-12 (CA3P) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short
G51-11 (CA3N) - G51-6 (GND) Engine switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

Ground short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)

B

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

C

18.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND GROUND)
3.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - ECM)
a.

Disconnect the G98 No. 3 junction connector.


U170105E02
1.385,0.99 0.979,0.594 0.979,0.594 0.896,0.594 true 1.396,1.208 0.99,1.594 0.99,1.594 0.906,1.594 true 0.49,0.521 0.927,0.698 0.438,0.177 10 false CANH 0.49,0.865 0.813,1.042 0.323,0.177 10 false G98 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a 0.531,1.51 0.969,1.688 0.438,0.177 10 false CANL

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-9 (CANH) - G98-20 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U170106E02
1.156,0.969 0.958,0.573 0.958,0.573 0.875,0.573 true 1.156,1.177 0.958,1.563 0.958,1.563 0.875,1.563 true 0.49,0.49 0.927,0.667 0.438,0.177 10 false CANH 0.479,0.813 0.802,0.99 0.323,0.177 10 false G98 0.458,1.469 0.896,1.646 0.438,0.177 10 false CANL 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-11 (CANH) - G98-22 (CANL) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

7.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 3 JUNCTION CONNECTOR)
a.
U170480E01
0.535,1.681 0.828,1.845 0.293,0.164 10 G57 0.209,0.143 0.406,0.324 0.197,0.180 10 *a 0.529,2.784 1.134,2.943 0.605,0.159 10 CANP 1.945,2.846 2.547,3.004 0.602,0.158 10 CANN 1.418,2.285 1.165,2.866 1.165,2.866 1.066,2.866 false 1.542,2.274 1.818,2.933 1.818,2.933 1.917,2.933 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-20 (CANP) - G57-21 (CANN) Engine switch off 108 to 132 Ω


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (ECM - NO. 3 JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS MAIN WIRE (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)
a.
U148237E03
1.969,1.302 2.417,0.385 2.417,0.385 2.542,0.385 true 2.042,1.292 2.583,0.917 2.583,0.917 2.75,0.917 true 0.021,0 0.26,0.188 0.24,0.188 10 true *a 2.792,0.854 3.25,1.01 0.458,0.156 10 false CA3N 2.573,0.292 3,0.448 0.427,0.156 10 false CA3P 0.583,1.188 0.917,1.344 0.333,0.156 10 false G51

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (POWER MANAGEMENT CONTROL ECU - NO. 3 JUNCTION CONNECTOR)

9.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U170000E02
1.625,2.51 0.969,2.375 0.969,2.375 0.885,2.375 true 2.427,3.094 2.365,3.094 2.365,3.094 2.198,2.938 true 1.375,1.156 1.094,0.771 1.094,0.771 1.01,0.771 true 1.385,1.354 1.104,1.75 1.104,1.75 1.021,1.75 true 0.448,2.656 0.771,2.833 0.323,0.177 10 false G48 0.177,2.24 0.385,2.417 0.208,0.177 10 false *b 0.177,0 0.385,0.177 0.208,0.177 10 false *a 0.635,2.292 0.865,2.469 0.229,0.177 10 false CG 2.469,3.021 2.865,3.198 0.396,0.177 10 false BAT 0.604,0.708 1.042,0.885 0.438,0.177 10 false CANH 0.521,1.115 0.844,1.292 0.323,0.177 10 false G98 0.625,1.667 1.063,1.844 0.438,0.177 10 false CANL

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-10 (CANH) - G98-21 (CANL) Engine switch off 200 Ω or higher
G98-10 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-21 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-10 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-21 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - ECM)

NG

12.CONNECT CONNECTOR
10.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - ECM)
a.
U170001E02
1.635,2.51 0.979,2.375 0.979,2.375 0.896,2.375 true 2.458,3.094 2.385,3.094 2.385,3.094 2.229,2.938 true 1.385,1.156 0.979,0.771 0.979,0.771 0.896,0.771 true 1.385,1.375 0.979,1.76 0.979,1.76 0.896,1.76 true 0.448,2.625 0.771,2.802 0.323,0.177 10 false G48 0.135,2.26 0.344,2.438 0.208,0.177 10 false *b 0.135,0.021 0.344,0.198 0.208,0.177 10 false *a 0.646,2.292 0.875,2.469 0.229,0.177 10 false CG 2.49,3.021 2.885,3.198 0.396,0.177 10 false BAT 0.479,0.688 0.917,0.865 0.438,0.177 10 false CANH 0.5,1.115 0.823,1.292 0.323,0.177 10 false G98 0.469,1.677 0.906,1.854 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-9 (CANH) - G98-20 (CANL) Engine switch off 108 to 132 Ω
G98-9 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-20 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-9 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-20 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)

NG

14.CONNECT CONNECTOR
11.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - POWER MANAGEMENT CONTROL ECU)
a.
U170002E02
1.635,2.521 0.979,2.385 0.979,2.385 0.896,2.385 true 2.458,3.073 2.385,3.073 2.385,3.073 2.229,2.917 true 1.156,1.146 0.75,0.76 0.75,0.76 0.667,0.76 true 1.156,1.365 0.75,1.75 0.75,1.75 0.667,1.75 true 0.448,2.625 0.76,2.802 0.313,0.177 10 false G48 0.135,2.26 0.344,2.438 0.208,0.177 10 false *b 0.135,0.021 0.344,0.198 0.208,0.177 10 false *a 0.646,2.302 0.875,2.479 0.229,0.177 10 false CG 2.49,2.99 2.885,3.167 0.396,0.177 10 false BAT 0.24,0.698 0.677,0.875 0.438,0.177 10 false CANH 0.479,1.073 0.802,1.25 0.323,0.177 10 false G98 0.25,1.656 0.688,1.833 0.438,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-11 (CANH) - G98-22 (CANL) Engine switch off 108 to 132 Ω
G98-11 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-22 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G98-11 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G98-22 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

16.CONNECT CONNECTOR
12.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

13.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
13.CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.
U148534E04
2.302,2.813 2.51,3.052 2.51,3.052 2.563,3.052 true 1.698,2.406 1.5,2 1.5,2 1.333,2 true 1.833,1.146 2.052,0.281 2.052,0.281 2.188,0.281 true 1.969,1.146 2.344,0.573 2.344,0.573 2.469,0.573 true 0.104,1.906 0.302,2.073 0.198,0.167 10 false *b 0.365,2.51 0.677,2.688 0.313,0.177 10 false G48 1.104,1.917 1.333,2.094 0.229,0.177 10 false CG 2.604,2.958 2.958,3.135 0.354,0.177 10 false BAT 0.115,0.052 0.292,0.26 0.177,0.208 10 false *a 0.771,0.302 1.083,0.479 0.313,0.177 10 false G25 2.219,0.188 2.656,0.396 0.438,0.208 10 false CANH 2.5,0.5 2.938,0.708 0.438,0.208 10 false CANL

Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) Engine switch off 54 to 69 Ω
G25-11 (CANH) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-12 (CANL) - G48-4 (CG) Engine switch off 200 Ω or higher
G25-11 (CANH) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G25-12 (CANL) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of DLC3



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)

14.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

15.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
15.CHECK FOR SHORT IN CAN BUS WIRES (ECM)
a.
U170213E01
0.637,0.82 0.930,0.984 0.293,0.164 10 G57 0.651,1.679 1.072,1.838 0.421,0.159 10 CANP 2.029,1.741 2.631,1.899 0.602,0.158 10 CANN 1.503,1.442 1.249,1.76 1.249,1.76 1.15,1.76 false 1.626,1.431 1.902,1.828 1.902,1.828 2.001,1.828 false 0.449,2.651 0.772,2.829 0.324,0.178 10 G48 0.062,0.016 0.275,0.194 0.213,0.178 10 *a 0.062,1.997 0.275,2.175 0.213,0.178 10 *b 1.136,2.103 1.371,2.281 0.235,0.178 10 CG 2.525,2.987 2.958,3.165 0.434,0.178 10 BAT 1.667,2.494 1.513,2.192 1.513,2.192 1.425,2.192 false 2.229,2.918 2.434,3.082 2.434,3.082 2.521,3.082 false

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G57-20 (CANP) - G57-21 (CANN) Engine switch off 108 to 132 Ω
G57-20 (CANP) - G48-4 (CG) Engine switch off 200 Ω or higher
G57-21 (CANN) - G48-4 (CG) Engine switch off 200 Ω or higher
G57-20 (CANP) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G57-21 (CANN) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE ECM MAIN WIRE OR CONNECTOR (CANP, CANN)

16.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

17.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
17.CHECK FOR SHORT IN CAN BUS WIRES (POWER MANAGEMENT CONTROL ECU)
a.
U148284E03
1.01,1.583 1.167,1.583 1.167,1.583 1.802,1.104 true 2.333,1.75 2.167,1.75 2.167,1.75 1.885,1.083 true 2.302,2.896 2.51,3.125 2.51,3.125 2.563,3.125 true 1.688,2.448 1.5,2.083 1.5,2.083 1.333,2.083 true 0.094,0.042 0.292,0.25 0.198,0.208 10 false *a 0.635,1.521 1.063,1.729 0.427,0.208 10 false CA3P 2.375,1.677 2.802,1.885 0.427,0.208 10 false CA3N 0.458,0.844 0.792,1.052 0.333,0.208 10 false G51 0.063,1.969 0.26,2.135 0.198,0.167 10 false *b 0.375,2.594 0.688,2.771 0.313,0.177 10 false G48 1.094,2 1.323,2.177 0.229,0.177 10 false CG 2.604,3.042 2.958,3.219 0.354,0.177 10 false BAT

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-11 (CA3N) - G48-4 (CG) Engine switch off 200 Ω or higher
G51-12 (CA3P) - G48-16 (BAT) Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G48-16 (BAT) Engine switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO POWER MANAGEMENT CONTROL ECU (CA3P, CA3N)

18.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND GROUND)
a.
U148238E03
2.594,0.625 2.521,0.625 2.521,0.625 2.344,1.167 true 2.438,1.188 2.656,0.875 2.656,0.875 2.75,0.875 true 1.021,1.688 1.094,1.688 1.094,1.688 1.427,1.198 true 1.354,1.208 0.979,1.458 0.979,1.458 0.885,1.458 true 0.042,0.031 0.281,0.219 0.24,0.188 10 true *a 2.781,0.813 3.208,0.969 0.427,0.156 10 false AM22 0.542,1.375 0.885,1.531 0.344,0.156 10 false GND 0.583,1.604 1.01,1.76 0.427,0.156 10 false GND2 2.625,0.552 3.031,0.708 0.406,0.156 10 false AM21 2.823,1.281 3.156,1.438 0.333,0.156 10 false G51

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the power management control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-5 (GND2) - Body ground Always Below 1 Ω
G51-6 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-1 (AM22) - Body ground Always 11 to 14 V
G51-2 (AM21) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR