| Symptom | Trouble Area |
|---|---|
| All DTCs related to the sub bus are output from the ECM. | ·
Local bus circuit ·
ECM ·
Urea pump control ECU ·
Nitrogen oxides sensor ·
No. 7 junction connector |
Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Measure the resistance according to the value(s) in the table below.
| *a | Component with harness connected
(ECM) |
- | - |
| Tester Connection | Switch Condition | Specified Condition | Resistance: Malfunction |
|---|---|---|---|
| G184-27 (CANU) - G184-35 (CAND) | Engine switch off | 54 to 69 Ω | Below 53 Ω: Short in line |
| G184-27 (CANU) - G184-35 (CAND) | Engine switch off | 54 to 69 Ω | Higher than 70 Ω: Open in CAN main bus line |
| G184-27 (CANU) - G185-1 (BATT) | Engine switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| G184-35 (CAND) - G185-1 (BATT) | Engine switch off | 6 kΩ or higher | Below 6 kΩ: +B short |
| G184-27 (CANU) - C152-1 (E1) | Engine switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| G184-35 (CAND) - C152-1 (E1) | Engine switch off | 200 Ω or higher | Below 200 Ω: Ground short |
| Result | Proceed to |
|---|---|
| NG
·
Open in CAN main bus line |
A |
| NG
·
Short in line ·
+B short ·
Ground short |
B |
| OK | C |
A
B
C
Disconnect the No. 7 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q41-4 (CANH) - Q41-15 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 7 Junction Connector) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q41-5 (CANH) - Q41-16 (CANL) | Engine switch off | 108 to 132 Ω |
| *a | Rear view of wire harness connector
(to No. 7 Junction Connector) |
OK
NG
Reconnect the Q41 No. 7 junction connector.
NEXT
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| s4-27 (CAN+) - s4-26 (CAN-) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to Urea Pump Control ECU) |
OK
NG
Reconnect the Q41 No. 7 junction connector.
NEXT
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G184-27 (CANU) - G184-35 (CAND) | Engine switch off | 108 to 132 Ω |
| *a | Front view of wire harness connector
(to ECM) |
OK
NG
Disconnect the No. 7 junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q41-6 (CANH) - Q41-17 (CANL) | Engine switch off | 200 Ω or higher |
| Q41-6 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-17 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-6 (CANH) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| Q41-17 (CANL) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 7 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q41-4 (CANH) - Q41-15 (CANL) | Engine switch off | 108 to 132 Ω |
| Q41-4 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-15 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-4 (CANH) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| Q41-15 (CANL) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 7 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| Q41-5 (CANH) - Q41-16 (CANL) | Engine switch off | 108 to 132 Ω |
| Q41-5 (CANH) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-16 (CANL) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| Q41-5 (CANH) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| Q41-16 (CANL) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Rear view of wire harness connector
(to No. 7 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the Q41 No. 7 junction connector.
NEXT
Disconnect the nitrogen oxides sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| s6-4 (CAN+) - s6-3 (CAN-) | Engine switch off | 54 to 69 Ω |
| s6-4 (CAN+) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| s6-3 (CAN-) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| s6-4 (CAN+) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| s6-3 (CAN-) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Nitrogen Oxides Sensor) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the Q41 No. 7 junction connector.
NEXT
Disconnect the urea pump control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| s4-27 (CAN+) - s4-26 (CAN-) | Engine switch off | 108 to 132 Ω |
| s4-27 (CAN+) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| s4-26 (CAN-) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| s4-27 (CAN+) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| s4-26 (CAN-) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to Urea Pump Control ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the Q41 No. 7 junction connector.
NEXT
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G184-27 (CANU) - G184-35 (CAND) | Engine switch off | 108 to 132 Ω |
| G184-27 (CANU) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G184-35 (CAND) - G48-4 (CG) | Engine switch off | 200 Ω or higher |
| G184-27 (CANU) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| G184-35 (CAND) - G48-16 (BAT) | Engine switch off | 6 kΩ or higher |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Connect the cable to the negative (-) battery terminal.
| *a | Front view of wire harness connector
(to ECM) |
- | - |
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C152-1 (E1) - Body ground | Always | Below 1 Ω |
| C151-3 (E01) - Body ground | Always | Below 1 Ω |
| C152-4 (E02) - Body ground | Always | Below 1 Ω |
| C152-3 (ME01) - Body ground | Always | Below 1 Ω |
| G185-8 (EC) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G185-1 (BATT) - Body ground | Always | 11 to 14 V |
| G185-2 (+B) - Body ground | Battery positive (+) voltage applied to terminal G184-14 (MREL) | 11 to 14 V |
| G185-3 (+B2) - Body ground | Battery positive (+) voltage applied to terminal G184-14 (MREL) | 11 to 14 V |
| G185-4 (+B3) - Body ground | Battery positive (+) voltage applied to terminal G184-14 (MREL) | 11 to 14 V |
OK
NG