CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
| *A | for LHD | *B | for RHD |
Disconnect the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the voltage and resistance according to the value(s) in the table below.
Measure the values on the wire harness side with the connector disconnected.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A-30 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-31 (ALTB) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| A-32 (IG) - Body ground | - | Ignition switch power supply | Ignition switch ON | 11 to 14 V |
| A-32 (IG) - Body ground | - | Ignition switch power supply | Ignition switch off | Below 1 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch ACC | 11 to 14 V |
| A-29 (ACC) - Body ground | - | ACC power supply | Ignition switch off | Below 1 V |
| A-11 (GND1) - Body ground | - | Ground | Always | Below 1 Ω |
| G63-3 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
Install the main body ECU (multiplex network body ECU).
Measure the voltage and waveform according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2I-27 (FLCY) - Body ground*1 | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| 2I-27 (FLCY) - Body ground*1 | R - Body ground | Front door LH courtesy light switch input | Front door LH closed | 11 to 14 V |
| 2D-31 (FLCY) - Body ground*2 | R - Body ground | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| 2D-31 (FLCY) - Body ground*2 | R - Body ground | Front door LH courtesy light switch input | Front door LH closed | 11 to 14 V |
| 2D-15 (FRCY) - Body ground*1 | B - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| 2D-15 (FRCY) - Body ground*1 | B - Body ground | Front door RH courtesy light switch input | Front door RH closed | 11 to 14 V |
| 2H-26 (FRCY) - Body ground*2 | B - Body ground | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| 2H-26 (FRCY) - Body ground*2 | B - Body ground | Front door RH courtesy light switch input | Front door RH closed | 11 to 14 V |
| G65-3 (LCTY) - Body ground*3 | V - Body ground | Rear door LH courtesy light switch input | Rear door LH open | Below 1 V |
| G65-3 (LCTY) - Body ground*3 | V - Body ground | Rear door LH courtesy light switch input | Rear door LH closed | 11 to 14 V |
| G64-6 (RCTY) - Body ground*3 | R - Body ground | Rear door RH courtesy light switch input | Rear door RH open | Below 1 V |
| G64-6 (RCTY) - Body ground*3 | R - Body ground | Rear door RH courtesy light switch input | Rear door RH closed | 11 to 14 V |
| G64-19 (BCTY) - Body ground | G - Body ground | Back door courtesy light switch input | Back door open | Below 1 V |
| G64-19 (BCTY) - Body ground | G - Body ground | Back door courtesy light switch input | Ignition switch off, all doors closed and back door closed | Pulse generation (See waveform 1 or 2) |
| G64-11 (L2) - Body ground | GR - Body ground | Driver side door key-linked lock input | Driver side door key cylinder in lock position | Below 1 V |
| G64-11 (L2) - Body ground | GR - Body ground | Driver side door key-linked lock input | Ignition switch off, all doors closed and driver side door key cylinder in neutral position | Pulse generation (See waveform 3 or 4) |
| G64-24 (UL3) - Body ground | LG - Body ground | Driver side door key-linked unlock input | Driver side door key cylinder in unlock position | Below 1 V |
| G64-24 (UL3) - Body ground | LG - Body ground | Driver side door key-linked unlock input | Ignition switch off, all doors closed and driver side door key cylinder in neutral position | Pulse generation (See waveform 5 or 6) |
| 2D-3 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output (all doors) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2D-3 (ACT+) - Body ground | L - Body ground | Door lock motor lock drive output (all doors) | Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V |
| 2I-8 (ACT+) - Body ground*1, *3 | L - Body ground | Door lock motor lock drive output (all doors) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2I-8 (ACT+) - Body ground*1, *3 | L - Body ground | Door lock motor lock drive output (all doors) | Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V |
| 2H-8 (ACT+) - Body ground*2, *3 | L - Body ground | Door lock motor lock drive output (all doors) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2H-8 (ACT+) - Body ground*2, *3 | L - Body ground | Door lock motor lock drive output (all doors) | Lock side of driver side door control switch pushed, or driver side door key cylinder in lock position | 11 to 14 V |
| 2D-1 (ACTD) - Body ground | G - Body ground | Driver side door lock motor unlock drive output | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2D-1 (ACTD) - Body ground | G - Body ground | Driver side door lock motor unlock drive output | Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V |
| 2D-2 (ACT-) - Body ground | W - Body ground | Door lock motor unlock drive output (except driver side) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2D-2 (ACT-) - Body ground | W - Body ground | Door lock motor unlock drive output (except driver side) | Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V |
| 2I-10 (ACT-) - Body ground*1, *3 | W - Body ground | Door lock motor unlock drive output (except driver side) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2I-10 (ACT-) - Body ground*1, *3 | W - Body ground | Door lock motor unlock drive output (except driver side) | Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V |
| 2H-10 (ACT-) - Body ground*1, *3 | W - Body ground | Door lock motor unlock drive output (except driver side) | Driver side door control switch not pushed and driver side door key cylinder in neutral position | Below 1 V |
| 2H-10 (ACT-) - Body ground*1, *3 | W - Body ground | Door lock motor unlock drive output (except driver side) | Unlock side of driver side door control switch pushed, or driver side door key cylinder in unlock position | 11 to 14 V |
| G64-7 (LSFL) - Body ground | G - Body ground | Front door LH lock position switch input | Front door LH unlocked | Below 1 V |
| G64-7 (LSFL) - Body ground | G - Body ground | Front door LH lock position switch input | Ignition switch off, all doors closed and front door LH locked | Pulse generation (See waveform 7 or 8) |
| G64-18 (LSFR) - Body ground | G - Body ground | Front door RH lock position switch input | Front door RH unlocked | Below 1 V |
| G64-18 (LSFR) - Body ground | G - Body ground | Front door RH lock position switch input | Ignition switch off, all doors closed and front door RH locked | Pulse generation (See waveform 9 or 10) |
| 2H-25 (LSWL) - Body ground*1, *3 | B - Body ground | Rear door LH lock position switch input | Rear door LH unlocked | Below 1 V |
| 2H-25 (LSWL) - Body ground*1, *3 | B - Body ground | Rear door LH lock position switch input | Ignition switch off, all doors closed and rear door LH locked | Pulse generation (See waveform 11 or 12) |
| 2D-16 (LSWL) - Body ground*2, *3 | B - Body ground | Rear door LH lock position switch input | Rear door LH unlocked | Below 1 V |
| 2D-16 (LSWL) - Body ground*2, *3 | B - Body ground | Rear door LH lock position switch input | Ignition switch off, all doors closed and rear door LH locked | Pulse generation (See waveform 13 or 14) |
| G63-2 (LSWR) - Body ground*3 | V - Body ground | Rear door RH lock position switch input | Rear door RH unlocked | Below 1 V |
| G63-2 (LSWR) - Body ground*3 | V - Body ground | Rear door RH lock position switch input | Ignition switch off, all doors closed and rear door RH locked | Pulse generation (See waveform 15 or 16) |
| G65-13 (LSWB) - Body ground | SB - Body ground | Back door lock position switch input | Back door lock unlocked | Below 1 V |
| G65-13 (LSWB) - Body ground | SB - Body ground | Back door lock position switch input | Ignition switch off, all doors closed and back door locked | Pulse generation (See waveform 17 or 18) |
| 2A-25 (GSW) - Body ground*4 | B - Body ground | Center airbag sensor signal | Ignition switch ON with the center airbag sensor assembly connector disconnected | 4.5 to 5.5 V |
*1: for LHD
*2: for RHD
*3: for 5 Door
*4: w/ Speed-sensitive Automatic Door Lock Function
If the result is not as specified, the main body ECU (multiplex network body ECU) or driver side junction block assembly may have a malfunction.
Using an oscilloscope, check waveform 1.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-19 (BCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and back door closed |
Using an oscilloscope, check waveform 2.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-19 (BCTY) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and back door closed |
Using an oscilloscope, check waveform 3.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door key cylinder in neutral position |
Using an oscilloscope, check waveform 4.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-11 (L2) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door key cylinder in neutral position |
Using an oscilloscope, check waveform 5.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-24 (UL3) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
Using an oscilloscope, check waveform 6.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-24 (UL3) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and driver side door key cylinder in neutral position |
Using an oscilloscope, check waveform 7.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door LH locked |
Using an oscilloscope, check waveform 8.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-7 (LSFL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door LH locked |
Using an oscilloscope, check waveform 9.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 10.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G64-18 (LSFR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and front door RH locked |
Using an oscilloscope, check waveform 11.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | 2H-25 (LSWL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door LH locked |
Using an oscilloscope, check waveform 12.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | 2H-25 (LSWL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door LH locked |
Using an oscilloscope, check waveform 13.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | 2D-16 (LSWL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door LH locked |
Using an oscilloscope, check waveform 14.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | 2D-16 (LSWL) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door LH locked |
Using an oscilloscope, check waveform 15.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G63-2 (LSWR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door RH locked |
Using an oscilloscope, check waveform 16.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G63-2 (LSWR) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and rear door RH locked |
Using an oscilloscope, check waveform 17.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G65-13 (LSWB) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and back door locked |
Using an oscilloscope, check waveform 18.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | G65-13 (LSWB) - Body ground |
| Tool Setting | 5 V/DIV., 20 ms/DIV. |
| Condition | Ignition switch off, all doors closed and back door locked |
CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>INSPECTION)