Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261039 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) C

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  B1242  Wireless Door Lock Tuner Circuit Malfunction  


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU. This DTC is stored when the applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.

DTC Code DTC Detection Condition Trouble Area
B1242 The applicable RDA signal cannot be received within 1 second of the PRG signal being output from the main body ECU.
·

Harness or connector

·

Door control receiver

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

B242194E02
0.699,2.952 2.132,3.128 1.434,0.177 10 Door Control Receiver 0.699,2.767 1.019,2.943 0.320,0.177 10 R26 2.055,0.712 2.376,0.889 0.320,0.177 10 3 1.601,0.805 1.957,0.982 0.356,0.177 10 PRG 2.055,1.212 2.376,1.388 0.320,0.177 10 2 4.983,2.178 5.303,2.355 0.320,0.177 10 G64 1.605,1.305 1.945,1.481 0.341,0.177 10 RDA 2.055,1.704 2.376,1.880 0.320,0.177 10 5 1.73,1.796 1.946,1.973 0.217,0.177 10 +B 2.055,2.15 2.376,2.326 0.320,0.177 10 1 1.611,2.243 1.945,2.419 0.334,0.177 10 GND 5.22,0.805 5.637,0.982 0.417,0.177 10 PRG 5.22,1.293 5.622,1.470 0.402,0.177 10 RDA 4.967,0.709 5.385,0.885 0.417,0.177 10 25 4.967,1.211 5.385,1.387 0.417,0.177 10 26 4.984,2.362 6.702,2.688 1.718,0.326 10 Main Body ECU (Multiplex Network Body ECU) 3.179,2.281 4.052,2.461 0.872,0.181 10 from Battery 2.464,1.922 2.941,2.103 0.477,0.181 10 ECU-B

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the door control receiver, refer to the registration procedures (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>REGISTRATION).



PROCEDURE

2.CHECK FOR DTC

OK

NG

3.CHECK DOOR CONTROL RECEIVER (DOOR CONTROL RECEIVER - MAIN BODY ECU)
3.CHECK DOOR CONTROL RECEIVER (DOOR CONTROL RECEIVER - MAIN BODY ECU)
a.

Disconnect the R26 receiver connector.


b.

Disconnect the G64 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-2 (RDA) - G64-26 (RDA) Always Below 1 Ω
R26-3 (PRG) - G64-25 (PRG)
R26-2 (RDA) or G64-26 (RDA) - Body ground Always 10 kΩ or higher
R26-3 (PRG) or G64-25 (PRG) - Body ground




OK

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
U169656E01
0.714,1.841 1.062,2.027 0.349,0.186 10 GND 2.311,1.841 2.532,2.027 0.221,0.186 10 +B 0.142,0.062 0.337,0.248 0.195,0.186 10 *a 0.452,1.067 0.801,1.253 0.349,0.186 10 R26 1.224,1.355 1.048,1.845 false 2.207,1.355 2.352,1.841 false

Disconnect the R26 receiver connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-1 (GND) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
R26-5 (+B) - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Door Control Receiver)



OK

5.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new one.





NEXT

6.CLEAR DTC
7.CHECK FOR DTC

OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)