Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2274  ACC Monitor Malfunction  


DESCRIPTION

This DTC is stored when there is a problem in the ACC output circuit, which is from the ACC output terminal of the power management control ECU to the ACC relay.

HINT:

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code DTC Detection Condition Trouble Area
B2274 The ACC relay actuation circuit inside the power management control ECU or other related circuit is malfunctioning.
·

AM2 fuse

·

Main body ECU (Driver side junction block assembly) (ACC relay)

·

Power management control ECU

·

Harness or connector



WIRING DIAGRAM

C217203E01
0.36,0.389 1.238,0.693 0.878,0.304 10 from Battery 1.51,0.538 1.813,0.675 0.303,0.137 10 AM2 2.908,0.42 3.297,0.557 0.389,0.137 10 AM21 2.908,0.814 3.290,0.951 0.382,0.137 10 AM22 3.379,0.813 3.790,0.950 0.412,0.137 10 ACCD 2.719,1.91 2.816,2.047 0.097,0.137 10 5 2.719,2.315 2.816,2.452 0.097,0.137 10 6 2.908,2.005 3.314,2.142 0.406,0.137 10 GND2 2.908,2.401 3.237,2.538 0.329,0.137 10 GND 2.663,2.746 2.992,2.883 0.329,0.137 10 G51 2.663,2.888 3.939,3.202 1.276,0.315 10 Power Management Control ECU 4.869,1.676 6.210,1.991 1.341,0.315 10 Driver Side Junction Block Assembly 2.714,0.315 2.811,0.452 0.097,0.137 10 2 2.716,0.71 2.810,0.847 0.094,0.137 10 1 3.861,0.708 4.037,0.846 0.175,0.137 10 19 4.504,0.807 4.761,0.944 0.257,0.137 10 2A 5.4,1.063 5.789,1.200 0.389,0.137 10 ACC 4.512,0.612 4.685,0.749 0.173,0.137 10 48 6.449,0.796 6.738,0.934 0.289,0.137 10 2D 6.497,0.612 6.594,0.749 0.096,0.137 10 4

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (ACC RELAY)
a.
U169670E02
1.771,3.021 2.24,3.021 false 1.073,1.542 1.635,1.542 false 2.302,1.51 2.51,1.677 0.208,0.167 10 false 2D 2.302,2.656 2.51,2.823 0.208,0.167 10 false 2A 0.26,0.135 0.469,0.302 0.208,0.167 10 false *a 0.667,1.438 1.031,1.604 0.365,0.167 10 false 2D-4 2.292,2.906 2.719,3.073 0.427,0.167 10 false 2A-48

Remove the driver side junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-48 - 2D-4 20°C (68°F) 101.25 to 123.75 Ω


Text in Illustration
*a Component without harness connected
(Driver Side Junction Block Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

4.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G51 power management control ECU connector.


b.

Disconnect the 2A driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-19 (ACCD) - 2A-48 Always Below 1 Ω
G51-19 (ACCD) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)

OK

6.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER MANAGEMENT CONTROL ECU
a.

Connect the power management control ECU connector.

U169907E01
0.135,0.091 0.337,0.251 0.202,0.160 10 *a 5.826,0.615 6.263,0.787 0.437,0.172 10 ACCD 5.424,1.637 5.684,0.677 5.684,0.677 5.795,0.677 false 4.502,0.684 4.797,0.847 0.296,0.163 10 G51

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
- -


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G51-19 (ACCD) - Body ground Engine switch off Below 1 V
Engine switch on (ACC) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher




OK

NG