Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2286  Runnable Signal Malfunction  P0335  Crankshaft Position Sensor Circuit Malfunction (NE Signal)  


DESCRIPTION

The power management control ECU and ECM are connected by a cable and the CAN communication lines. These DTCs are stored when the crankshaft position sensor signal information from the cable and the crankshaft position sensor signal information from the CAN communication line are inconsistent.

HINT:

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code DTC Detection Condition Trouble Area
B2286
P0335
The crankshaft position sensor signal information from the cable and the crankshaft position sensor signal information from the CAN communication line are inconsistent.
·

AM2 fuse

·

Engine control system

·

Power management control ECU

·

Harness or connector



WIRING DIAGRAM

C332683E02
0.948,1.313 1.302,1.458 0.354,0.146 10 false NEO 2.948,0.667 3.354,0.813 0.406,0.146 10 false AM2 0.385,2.49 2.24,2.635 1.854,0.146 10 false G56*1, C35*2 4.938,1.313 5.24,1.458 0.302,0.146 10 false G50 4.938,0.927 5.24,1.073 0.302,0.146 10 false G51 5.333,1.313 5.76,1.458 0.427,0.146 10 false NE 5.333,0.927 5.76,1.073 0.427,0.146 10 false AM22 5.333,0.531 5.76,0.677 0.427,0.146 10 false AM21 4.938,0.531 5.24,0.677 0.302,0.146 10 false G51 0.385,2.625 0.74,2.833 0.354,0.208 10 false ECM 5.063,2.49 6.313,2.865 1.25,0.375 10 false Power Management Control ECU 6.271,2.063 6.573,2.208 0.302,0.146 10 false G51 6.271,1.667 6.573,1.813 0.302,0.146 10 false G51 5.021,0.323 5.167,0.469 0.146,0.146 10 false 2 5.021,1.125 5.167,1.271 0.146,0.146 10 false 4 5.031,0.729 5.177,0.875 0.146,0.146 10 false 1 6.375,1.875 6.521,2.021 0.146,0.146 10 false 5 6.375,1.479 6.521,1.625 0.146,0.146 10 false 6 5.74,2.073 6.156,2.219 0.417,0.146 10 false GND2 5.854,1.667 6.219,1.813 0.365,0.146 10 false GND 0.198,0.469 0.99,0.646 0.792,0.177 10 false from Battery 1.354,1.208 3.031,1.354 1.677,0.146 10 false 13*1, 29*2 0.708,3.333 2.438,3.521 1.729,0.188 10 false : CAN Communication Line 1.917,2.635 4.5,2.823 2.583,0.188 10 false *1: for Automatic Transmission 1.917,2.927 4.188,3.115 2.271,0.188 10 false *2: for Manual Transmission 0.073,0.021 1.156,0.219 1.083,0.198 12 false for 1GR-FE:

E350146E01
0.094,0.063 2.115,0.302 2.021,0.24 12 false for 2TR-FE: 0.729,3.333 4.396,3.531 3.667,0.198 10 false : CAN Communication Line 0.667,0.667 2.5,0.865 1.833,0.198 10 false from Battery 3.01,0.844 3.469,1.042 0.458,0.198 10 false AM2 1.302,1.49 1.917,1.688 0.615,0.198 10 false G180 1.406,1.271 1.719,1.469 0.313,0.198 10 false 16 0.938,1.479 1.396,1.677 0.458,0.198 10 false NEO 4.948,0.698 5.406,0.896 0.458,0.198 10 false G51 4.948,1.094 5.406,1.292 0.458,0.198 10 false G51 4.948,1.49 5.406,1.688 0.458,0.198 10 false G50 6.271,1.844 6.729,2.042 0.458,0.198 10 false G51 6.26,2.229 6.719,2.427 0.458,0.198 10 false G51 5.188,2.667 6.448,3.01 1.26,0.344 10 false Power Management Control ECU 0.635,2.698 1.094,2.896 0.458,0.198 10 false ECM 5.333,0.677 5.948,0.875 0.615,0.198 10 false AM21 5.333,1.094 5.948,1.292 0.615,0.198 10 false AM22 5.333,1.49 5.948,1.688 0.615,0.198 10 false NE 5.813,1.833 6.427,2.031 0.615,0.198 10 false GND 5.76,2.229 6.375,2.427 0.615,0.198 10 false GND2 5.021,0.49 5.177,0.688 0.156,0.198 10 false 2 5.031,0.906 5.188,1.104 0.156,0.198 10 false 1 5.031,1.302 5.188,1.5 0.156,0.198 10 false 4 6.344,1.635 6.5,1.833 0.156,0.198 10 false 6 6.365,2.052 6.521,2.25 0.156,0.198 10 false 5

E350146E02
0.094,0.063 2.115,0.302 2.021,0.24 12 false for 1KD-FTV: 0.729,3.333 4.396,3.531 3.667,0.198 10 false : CAN Communication Line 0.667,0.667 2.5,0.865 1.833,0.198 10 false from Battery 3.01,0.844 3.469,1.042 0.458,0.198 10 false AM2 0.938,1.479 1.396,1.677 0.458,0.198 10 false NEO 4.948,0.698 5.406,0.896 0.458,0.198 10 false G51 4.948,1.094 5.406,1.292 0.458,0.198 10 false G51 4.948,1.49 5.406,1.688 0.458,0.198 10 false G50 6.271,1.844 6.729,2.042 0.458,0.198 10 false G51 6.26,2.229 6.719,2.427 0.458,0.198 10 false G51 5.188,2.667 6.448,3.01 1.26,0.344 10 false Power Management Control ECU 0.635,2.698 1.094,2.896 0.458,0.198 10 false ECM 5.333,0.677 5.948,0.875 0.615,0.198 10 false AM21 5.333,1.094 5.948,1.292 0.615,0.198 10 false AM22 5.333,1.49 5.948,1.688 0.615,0.198 10 false NE 5.813,1.833 6.427,2.031 0.615,0.198 10 false GND 5.76,2.229 6.375,2.427 0.615,0.198 10 false GND2 5.021,0.49 5.177,0.688 0.156,0.198 10 false 2 5.031,0.906 5.188,1.104 0.156,0.198 10 false 1 5.031,1.302 5.188,1.5 0.156,0.198 10 false 4 6.344,1.635 6.5,1.833 0.156,0.198 10 false 6 6.365,2.052 6.521,2.25 0.156,0.198 10 false 5 1.354,1.49 1.813,1.688 0.458,0.198 10 false G58 1.438,1.271 1.594,1.469 0.156,0.198 10 false 1

E350146E03
0.094,0.063 2.115,0.302 2.021,0.24 12 false for 1GD-FTV: 0.729,3.333 4.396,3.531 3.667,0.198 10 false : CAN Communication Line 0.667,0.667 2.5,0.865 1.833,0.198 10 false from Battery 3.01,0.844 3.469,1.042 0.458,0.198 10 false AM2 0.938,1.479 1.396,1.677 0.458,0.198 10 false NEO 4.948,0.698 5.406,0.896 0.458,0.198 10 false G51 4.948,1.094 5.406,1.292 0.458,0.198 10 false G51 4.948,1.49 5.406,1.688 0.458,0.198 10 false G50 6.271,1.844 6.729,2.042 0.458,0.198 10 false G51 6.26,2.229 6.719,2.427 0.458,0.198 10 false G51 5.188,2.667 6.448,3.01 1.26,0.344 10 false Power Management Control ECU 0.635,2.698 1.094,2.896 0.458,0.198 10 false ECM 5.333,0.677 5.948,0.875 0.615,0.198 10 false AM21 5.333,1.094 5.948,1.292 0.615,0.198 10 false AM22 5.333,1.49 5.948,1.688 0.615,0.198 10 false NE 5.813,1.833 6.427,2.031 0.615,0.198 10 false GND 5.76,2.229 6.375,2.427 0.615,0.198 10 false GND2 5.021,0.49 5.177,0.688 0.156,0.198 10 false 2 5.031,0.906 5.188,1.104 0.156,0.198 10 false 1 5.031,1.302 5.188,1.5 0.156,0.198 10 false 4 6.344,1.635 6.5,1.833 0.156,0.198 10 false 6 6.365,2.052 6.521,2.25 0.156,0.198 10 false 5 1.302,1.5 1.917,1.698 0.615,0.198 10 false G184 1.396,1.292 1.708,1.49 0.313,0.198 10 false 23

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)

OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ECM)
a.

Disconnect the G50 power management control ECU connector.


b.

Disconnect the G56*1, C35*2, G180*3, G58*4 or G184*5 ECM connector.

*1: for 1GR-FE (for Automatic Transmission)

*2: for 1GR-FE (for Manual Transmission)

*3: for 2TR-FE

*4: for 1KD-FTV

*5: for 1GD-FTV



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE (for Automatic Transmission):
Tester Connection Condition Specified Condition
G50-4 (NE) - G56-13 (NEO) Always Below 1 Ω
G50-4 (NE) - Body ground Always 10 kΩ or higher

for 1GR-FE (for Manual Transmission):
Tester Connection Condition Specified Condition
G50-4 (NE) - C35-29 (NEO) Always Below 1 Ω
G50-4 (NE) - Body ground Always 10 kΩ or higher

for 2TR-FE:
Tester Connection Condition Specified Condition
G50-4 (NE) - G180-16 (NEO) Always Below 1 Ω
G50-4 (NE) - Body ground Always 10 kΩ or higher

for 1KD-FTV:
Tester Connection Condition Specified Condition
G50-4 (NE) - G58-1 (NEO) Always Below 1 Ω
G50-4 (NE) - Body ground Always 10 kΩ or higher

for 1GD-FTV:
Tester Connection Condition Specified Condition
G50-4 (NE) - G184-23 (NEO) Always Below 1 Ω
G50-4 (NE) - Body ground Always 10 kΩ or higher




OK

4.READ VALUE USING INTELLIGENT TESTER (ENGINE CONDITION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING INTELLIGENT TESTER (ENGINE CONDITION)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Power Source Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Engine Condition Engine condition / Stop or Run Stop: Engine stopped
Run: Engine running
-

OK:

Stop (engine stopped) or Run (engine running) appears on the screen according to the engine condition.


Result
Result Proceed to
OK (for 1GR-FE and 2TR-FE) A
OK (for 1KD-FTV and 1GD-FTV) B
NG C

HINT:
·

for 1GR-FE:

If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 2TR-FE:

If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1KD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV (w/ Urea SCR System):

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).





A

GO TO SFI SYSTEM

B

GO TO ECD SYSTEM

C

5.CHECK POWER MANAGEMENT CONTROL ECU
5.CHECK POWER MANAGEMENT CONTROL ECU
a.

Reconnect the power management control ECU connectors.

U169909E01
0.135,0.091 0.337,0.251 0.202,0.160 10 *a 2.333,0.255 2.574,0.427 0.240,0.172 10 NE 1.931,1.277 2.191,0.317 2.191,0.317 2.302,0.317 false 2.45,0.761 2.753,0.932 0.303,0.172 10 G50

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
- -


b.

Using an oscilloscope, check the engine speed input signal waveform at the terminal of the power management control ECU.

Standard Frequency:
Tester Connection Condition Specified Condition
G50-4 (NE) - Body ground Engine stopped No pulse generated
Engine running Pulse generated
(1000 rpm: 200 Hz)


Result
Result Proceed to
OK A
NG (for 1GR-FE and 2TR-FE) B
NG (for 1KD-FTV and 1GD-FTV) C

HINT:
·

for 1GR-FE:

If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 2TR-FE:

If it is necessary to refer to the SFI system, refer to the following procedure (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1KD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV:

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

for 1GD-FTV (w/ Urea SCR System):

If it is necessary to refer to the ECD system, refer to the following procedure (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>HOW TO PROCEED WITH TROUBLESHOOTING).





A

B

GO TO SFI SYSTEM

C

GO TO ECD SYSTEM