Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The security courtesy switch is built into the hood lock. This switch turns on when the engine hood is opened and turns off when the engine hood is closed.


WIRING DIAGRAM

B240857E01
4.751,1.582 6.435,1.916 1.684,0.334 10 Main Body ECU (Multiplex Network Body ECU) 1.371,1.622 3.014,1.807 1.643,0.185 10 Security Courtesy Switch 1.371,1.451 1.699,1.648 0.328,0.197 10 A27 4.39,0.376 4.582,0.531 0.192,0.155 10 20 4.41,0.546 4.525,0.701 0.115,0.155 10 A 4.656,0.543 5.066,0.698 0.410,0.155 10 HCTY 4.39,1.018 4.582,1.173 0.192,0.155 10 12 4.319,1.183 4.653,1.338 0.334,0.155 10 G64 4.656,1.185 5.066,1.340 0.410,0.155 10 HD2 2.861,1.088 2.981,1.243 0.119,0.155 10 2 2.861,0.446 2.971,0.601 0.110,0.155 10 1 1.419,1.088 1.538,1.243 0.119,0.155 10 3 1.418,0.446 1.529,0.601 0.110,0.155 10 4

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (SECURITY COURTESY SWITCH)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Hood Courtesy SW Security courtesy switch /
ON or OFF
ON: Engine hood open
OFF: Engine hood closed
-

OK:

ON (engine hood open) and OFF (engine hood closed) appear on screen according to condition of engine hood.




OK

2.INSPECT SECURITY COURTESY SWITCH

NG

4.INSPECT SECURITY COURTESY SWITCH
2.INSPECT SECURITY COURTESY SWITCH
a.
B238373

Disconnect the A27 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (SECURITY COURTESY SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (SECURITY COURTESY SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the A27 switch connector.


b.

Disconnect the G64 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-2 - G64-12 (HD2) Always Below 1 Ω
A27-3 - Body ground Always Below 1 Ω
A27-2 or G64-12 (HD2) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE SECURITY COURTESY SWITCH

4.INSPECT SECURITY COURTESY SWITCH
a.
B238373

Disconnect the A27 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 4 Unlock position Below 1 Ω
1 - 4 Lock position 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (SECURITY COURTESY SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SECURITY COURTESY SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the A27 switch connector.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-1 - A-20 (HCTY) Always Below 1 Ω
A27-4 - Body ground Always Below 1 Ω
A27-1 or A-20 (HCTY) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE SECURITY COURTESY SWITCH