Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2768  Tilt Sensor Internal Circuit Malfunction  


DESCRIPTION

This DTC is stored when one of the following occurs: 1) a yaw rate sensor assembly power supply malfunction; 2) a yaw rate sensor assembly open malfunction; or 3) an EEPROM malfunction.

DTC Code DTC Detection Condition Trouble Area
B2768 One of the following conditions is met:
·

A yaw rate sensor assembly power supply malfunction.

·

A yaw rate sensor assembly open malfunction.

·

An EEPROM malfunction.


·

Yaw rate sensor assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B240858E01
4.93,0.425 5.165,0.598 0.235,0.174 10 +B 3.556,0.559 4.028,0.732 0.473,0.174 10 ECU-B 3.333,1.084 4.243,1.258 0.910,0.174 10 ECU-IG NO. 1 1.058,0.935 2.455,1.109 1.397,0.174 10 from IG1 NO. 1 Relay 1.674,0.43 2.460,0.604 0.786,0.174 10 from Battery 4.726,0.339 4.861,0.512 0.136,0.174 10 6 4.93,0.946 5.165,1.119 0.235,0.174 10 IG 4.726,0.859 4.861,1.033 0.136,0.174 10 4 4.93,1.476 5.298,1.650 0.368,0.174 10 GND 4.327,1.854 4.695,2.028 0.368,0.174 10 G52 4.327,2.005 6.093,2.178 1.766,0.174 10 Yaw Rate Sensor Assembly 4.726,1.39 4.820,1.563 0.094,0.174 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When replacing the yaw rate sensor assembly, perform zero point calibration.

Vehicle stability control system (for Hydraulic Brake Booster) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

Vehicle stability control system (for Vacuum Brake Booster) (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR - BATTERY AND BODY GROUND)
a.
U169782E01
1.541,0.47 1.867,0.634 0.326,0.164 10 G52 0.388,1.059 0.715,1.224 0.326,0.164 10 GND 2.472,0.674 2.798,0.838 0.326,0.164 10 IG 2.77,1.044 3.096,1.209 0.326,0.164 10 +B 0.086,0.072 0.412,0.236 0.326,0.164 10 *a 0.813,1.179 1.253,1.355 false 2.158,1.341 2.724,1.148 false 1.977,1.352 2.435,0.847 false

Disconnect the G52 sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-1 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G52-6 (+B) - Body ground Always 11 to 14 V
G52-4 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Yaw Rate Sensor Assembly)


OK

2.CHECK FOR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FOR DTC

b.

Turn the ignition switch to ON, and then off.


c.

Set the theft deterrent system to the armed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


d.

Check that the security indicator light changes from illuminated to flashing.


e.

Set the theft deterrent system to the disarmed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


f.


OK

NG

3.REPLACE YAW RATE SENSOR ASSEMBLY
3.REPLACE YAW RATE SENSOR ASSEMBLY
a.

Temporarily replace the yaw rate sensor assembly with a new or normally functioning one (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>REMOVAL).



NEXT

4.CHECK FOR DTC
4.CHECK FOR DTC

b.

Turn the ignition switch to ON, and then off.


c.

Set the theft deterrent system to the armed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


d.

Check that the security indicator light changes from illuminated to flashing.


e.

Set the theft deterrent system to the disarmed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


f.


OK

END (YAW RATE SENSOR ASSEMBLY IS DEFECTIVE)

NG