Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2769  Tilt Sensor Signal Circuit Malfunction  B276A  Short to GND in Tilt Sensor Signal Circuit  


DESCRIPTION

The yaw rate sensor assembly conducts a self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the CSIF-GCS line, the main body ECU stores DTC B2769.

DTC B276A is stored when terminal CSIF of the yaw rate sensor assembly has not received a signal for 5 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2769 After a normal/trouble signal is output from the yaw rate sensor assembly as a result of self-diagnosis, following malfunctions are detected:
·

The CSIF-GCS line circuit is open.

·

Reception of signals other than a normal/trouble signal.


·

Yaw rate sensor assembly

·

Main body ECU

·

Harness or connector


B276A Terminal CSIF of the yaw rate sensor assembly has not received a signal for 5 seconds or more.
·

Yaw rate sensor assembly

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B224123E03
4.919,1.827 6.586,2.187 1.667,0.360 10 Main Body ECU (Multiplex Network Body ECU) 5.111,0.842 5.243,1.011 0.132,0.170 10 6 5.346,0.939 5.836,1.123 0.489,0.184 10 GCS 1.942,0.85 2.141,1.020 0.199,0.170 10 5 1.479,0.969 1.822,1.152 0.343,0.184 10 CSIF 0.961,1.663 1.247,1.816 0.286,0.153 10 G52 0.961,1.827 2.730,2.001 1.769,0.174 10 Yaw Rate Sensor Assembly 4.919,1.663 5.271,1.804 0.353,0.141 10 G63

CAUTION / NOTICE / HINT

NOTICE:

When replacing the yaw rate sensor assembly, perform zero point calibration.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (YAW RATE SENSOR - MAIN BODY ECU)
a.

Disconnect the G52 sensor connector.


b.

Disconnect the G63 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G52-5 (CSIF) - G63-6 (GCS) Always Below 1 Ω
G52-5 (CSIF) or G63-6 (GCS) - Body ground Always 10 kΩ or higher




OK

2.REPLACE YAW RATE SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE YAW RATE SENSOR ASSEMBLY
a.

Temporarily replace the yaw rate sensor assembly with a new or normally functioning one (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>YAW RATE AND ACCELERATION SENSOR>REMOVAL).



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

b.

Turn the ignition switch to ON, and then off.


c.

Set the theft deterrent system to the armed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


d.

Check that the security indicator light changes from illuminated to flashing.


e.

Set the theft deterrent system to the disarmed state (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>SYSTEM DESCRIPTION).


f.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2769 or B276A is not output.




OK

END (YAW RATE SENSOR ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)