Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and front seat airbag RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1820/55 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the side squib RH circuit during the primary check.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1821/55 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the side squib RH circuit for 2 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1822/55 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly


B1823/55 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.

·

A side squib RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Side squib RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C174615E26
4.847,2.502 5.256,2.667 0.409,0.165 10 SFR- 4.847,1.648 5.302,1.814 0.455,0.166 10 SFR+ 1.928,2.602 2.355,2.766 0.427,0.165 10 SFR- 1.928,1.529 2.355,1.694 0.427,0.165 10 SFR+ 2.472,2.374 2.675,2.555 0.203,0.181 10 2 2.472,1.52 2.675,1.701 0.203,0.181 10 1 0.935,3.292 2.242,3.468 1.307,0.177 10 Side Squib RH 0.935,3.128 1.276,3.266 0.341,0.138 10 Q7 4.931,4.494 6.329,4.671 1.398,0.177 10 Center Airbag Sensor 4.931,4.331 5.272,4.469 0.341,0.138 10 Q1 4.561,1.555 4.783,1.721 0.222,0.166 10 7 4.559,2.369 4.781,2.535 0.222,0.166 10 6

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (SIDE SQUIB RH)
a.
U148745E03
2.042,2.5 2.271,2.594 2.271,2.594 2.5,2.594 false 1.125,1.031 1.125,0.51 1.125,0.51 1.323,0.51 false 1.292,1.281 1.469,1.458 0.177,0.177 10 false C 1.083,1.271 1.219,1.469 0.135,0.198 10 false D 0.594,2.021 0.802,2.177 0.208,0.156 10 false Q7 1.615,1.344 1.792,1.521 0.177,0.177 10 false *2 1.552,1.688 1.74,1.865 0.188,0.177 10 false *a 2.573,2.49 2.75,2.667 0.177,0.177 10 false *4 2.688,1.969 2.865,2.146 0.177,0.177 10 false *3 1.833,1.052 1.958,1.229 0.125,0.177 10 false A 1.375,0.438 1.563,0.615 0.188,0.177 10 false *1

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag RH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Squib RH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Side Squib RH)



OK

NG

2.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
2.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)
a.
U148539E03
1,1.063 1,0.542 1,0.542 1.052,0.542 false 1.521,1.063 1.521,0.542 1.521,0.542 1.563,0.542 false 1.563,2.552 1.146,2.74 false 1.813,2.552 2.188,2.74 false 1.271,1.323 1.448,1.5 0.177,0.177 10 false C 1.688,1.323 1.865,1.5 0.177,0.177 10 false B 1.052,1.323 1.188,1.521 0.135,0.198 10 false D 0.531,2.021 0.823,2.177 0.292,0.156 10 false Q7 1.906,1.354 2.083,1.531 0.177,0.177 10 false *3 1.573,1.771 1.75,1.948 0.177,0.177 10 false *a 2.396,2.177 2.573,2.354 0.177,0.177 10 false *4 2.063,1.052 2.188,1.229 0.125,0.177 10 false A 1.198,0.479 1.385,0.656 0.188,0.177 10 false *1 1.635,0.479 1.823,0.656 0.188,0.177 10 false *2 0.719,2.667 1.115,2.813 0.396,0.146 10 false SFR+ 2.281,2.667 2.646,2.813 0.365,0.146 10 false SFR-

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.

Disconnect the connectors from the center airbag sensor.


e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q7-1 (SFR+) - Body ground Ignition switch ON Below 1 V
Q7-2 (SFR-) - Body ground Ignition switch ON Below 1 V



g.

Turn the ignition switch off.


h.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q7-1 (SFR+) - Q7-2 (SFR-) Always Below 1 Ω



j.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


k.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q7-1 (SFR+) - Q7-2 (SFR-) Always 1 MΩ or higher
Q7-1 (SFR+) - Body ground Always 1 MΩ or higher
Q7-2 (SFR-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Side Squib RH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Side Squib RH)


OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE FLOOR WIRE

3.CHECK CENTER AIRBAG SENSOR
a.
C146261E80
0.823,1.125 0.823,1.51 false 0.708,1.625 0.906,1.823 0.198,0.198 10 false *1 0.958,1.208 1.083,1.406 0.125,0.198 10 false D 1.104,1.208 1.25,1.396 0.146,0.188 10 false C 1.479,1.479 1.677,1.646 0.198,0.167 10 false *2

Connect the connectors to the front seat airbag RH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1820, B1821, B1822 or B1823 is not output.


HINT:

Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Squib RH
*2 Center Airbag Sensor



OK

NG