Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835/58  Short in Curtain Shield Squib LH Circuit  B1836/58  Open in Curtain Shield Squib LH Circuit  B1837/58  Short to GND in Curtain Shield Squib LH Circuit  B1838/58  Short to B+ in Curtain Shield Squib LH Circuit  


DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor and curtain shield airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1835/58 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor assembly


B1836/58 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the curtain shield squib LH circuit for 2 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor assembly


B1837/58 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor assembly


B1838/58 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor assembly



WIRING DIAGRAM

U169903E02
0.74,3.24 3.135,3.406 2.396,0.167 10 false Curtain Shield Squib RH 2.052,1.521 2.427,1.708 0.375,0.188 10 false ICL+ 0.188,0.031 1.25,0.344 1.063,0.313 12 false for 5 Door: 4.771,1.625 5.167,1.813 0.396,0.188 10 false ICL+ 2.073,2.344 2.427,2.531 0.354,0.188 10 false ICL- 4.781,2.469 5.177,2.656 0.396,0.188 10 false ICL- 2.458,1.5 2.604,1.667 0.146,0.167 10 false 1 2.479,2.344 2.635,2.5 0.156,0.156 10 false 2 4.583,1.531 4.698,1.698 0.115,0.167 10 false 7 4.583,2.375 4.698,2.542 0.115,0.167 10 false 6 4.76,4.167 5.083,4.354 0.323,0.188 10 false R1 4.75,4.302 6.198,4.51 1.448,0.208 10 false Center Airbag Sensor 0.74,3.042 1.094,3.198 0.354,0.156 10 false R5

U169904E02
0.719,3.188 3.115,3.354 2.396,0.167 10 false Curtain Shield Squib RH 2.052,1.563 2.427,1.75 0.375,0.188 10 false ICL+ 0.188,0.031 1.25,0.344 1.063,0.313 12 false for 3 Door: 4.771,1.656 5.167,1.844 0.396,0.188 10 false ICL+ 2.073,2.385 2.427,2.573 0.354,0.188 10 false ICL- 4.781,2.51 5.177,2.698 0.396,0.188 10 false ICL- 2.458,1.552 2.604,1.719 0.146,0.167 10 false 1 2.479,2.385 2.635,2.542 0.156,0.156 10 false 2 4.583,1.563 4.698,1.729 0.115,0.167 10 false 7 4.583,2.396 4.781,2.563 0.198,0.167 10 false 6 4.76,4.146 5.083,4.333 0.323,0.188 10 false R1 4.75,4.354 6.198,4.563 1.448,0.208 10 false Center Airbag Sensor 0.75,3.01 1.104,3.167 0.354,0.156 10 false R35

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result
Result Proceed to
for 3 Door A
for 5 Door B



B

2.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)

A

6.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
2.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
a.
U148746E03
2.073,2.656 2.344,2.792 false 1.833,0.781 1.958,0.927 0.125,0.146 10 false A 1.302,0.99 1.427,1.135 0.125,0.146 10 false C 1.073,0.99 1.198,1.135 0.125,0.146 10 false D 0.885,0.542 1.042,0.719 0.156,0.177 10 false *1 1.646,1.344 1.802,1.521 0.156,0.177 10 false *2 2.396,1.865 2.552,2.042 0.156,0.177 10 false *3 2.385,2.729 2.542,2.906 0.156,0.177 10 false *4 1.604,1.688 1.781,1.833 0.177,0.146 10 false *a 0.729,1.875 0.938,2.031 0.208,0.156 10 false R5

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the curtain shield airbag LH.


d.

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib LH)



OK

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C208251E02
0.602,0.763 0.772,0.932 0.170,0.170 10 *1 1.72,1.622 1.889,1.792 0.170,0.170 10 *2 1.892,0.986 2.020,1.156 0.128,0.170 10 A 1.496,1.278 1.624,1.448 0.128,0.170 10 B 1.101,1.278 1.229,1.448 0.128,0.170 10 C 0.86,1.278 0.988,1.448 0.128,0.170 10 D

Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor



OK

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)
a.
U148540E03
0.969,0.781 0.969,0.51 0.969,0.51 1.021,0.51 false 1.542,0.781 1.542,0.51 1.542,0.51 1.594,0.51 false 1.542,2.542 1.125,2.729 false 1.823,2.552 2.208,2.74 false 1.281,1.021 1.458,1.198 0.177,0.177 10 false C 1.688,1.021 1.865,1.198 0.177,0.177 10 false B 1.073,1.021 1.208,1.219 0.135,0.198 10 false D 0.531,2.021 0.823,2.177 0.292,0.156 10 false R5 1.906,1.354 2.083,1.531 0.177,0.177 10 false *3 1.677,1.771 1.854,1.948 0.177,0.177 10 false *a 2.313,2.167 2.49,2.344 0.177,0.177 10 false *4 2.063,0.75 2.188,0.927 0.125,0.177 10 false A 1.042,0.427 1.229,0.604 0.188,0.177 10 false *1 1.656,0.427 1.844,0.604 0.188,0.177 10 false *2 0.771,2.667 1.156,2.813 0.385,0.146 10 false ICR+ 2.25,2.667 2.552,2.813 0.302,0.146 10 false ICR-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R5-1 (ICL+) - Body ground Ignition switch ON Below 1 V
R5-2 (ICL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-1 (ICL+) - R5-2 (ICL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-1 (ICL+) - R5-2 (ICL-) Always 1 MΩ or higher
R5-1 (ICL+) - Body ground Always 1 MΩ or higher
R5-2 (ICL-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Curtain Shield Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C207519E03
1.562,1.619 1.746,1.775 0.184,0.156 10 *2 0.817,0.828 1.001,0.984 0.184,0.156 10 *1 1.024,1.252 1.161,1.417 0.137,0.165 10 D 1.172,1.252 1.310,1.417 0.137,0.165 10 C

Connect the connectors to the curtain shield airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor



OK

NG

6.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
a.
U170236E02
2.063,2.583 2.333,2.719 false 1.854,0.74 1.979,0.885 0.125,0.146 10 false A 1.302,0.969 1.427,1.115 0.125,0.146 10 false C 1.063,0.969 1.188,1.115 0.125,0.146 10 false D 0.896,0.531 1.052,0.708 0.156,0.177 10 false *1 1.688,1.313 1.844,1.49 0.156,0.177 10 false *2 2.385,1.865 2.542,2.042 0.156,0.177 10 false *3 2.375,2.677 2.531,2.854 0.156,0.177 10 false *4 1.625,1.615 1.802,1.76 0.177,0.146 10 false *a 0.635,1.896 0.906,2.052 0.271,0.156 10 false R35

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the curtain shield airbag LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib LH)



OK

NG

7.CHECK CONNECTOR
7.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C208251E02
0.602,0.763 0.772,0.932 0.170,0.170 10 *1 1.72,1.622 1.889,1.792 0.170,0.170 10 *2 1.892,0.986 2.020,1.156 0.128,0.170 10 A 1.496,1.278 1.624,1.448 0.128,0.170 10 B 1.101,1.278 1.229,1.448 0.128,0.170 10 C 0.86,1.278 0.988,1.448 0.128,0.170 10 D

Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor



OK

8.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)
a.
U170237E02
0.969,0.771 0.969,0.5 0.969,0.5 1.021,0.5 false 1.5,0.771 1.5,0.5 1.5,0.5 1.542,0.5 false 1.542,2.375 1.125,2.573 false 1.771,2.365 2.167,2.563 false 1.302,1.021 1.479,1.198 0.177,0.177 10 false C 1.677,1.021 1.854,1.198 0.177,0.177 10 false B 1.083,1.021 1.219,1.219 0.135,0.198 10 false D 0.51,2.021 0.802,2.177 0.292,0.156 10 false R35 1.917,1.354 2.094,1.531 0.177,0.177 10 false *3 1.563,1.771 1.74,1.948 0.177,0.177 10 false *a 2.281,2.167 2.458,2.344 0.177,0.177 10 false *4 2.052,0.76 2.177,0.938 0.125,0.177 10 false A 1.073,0.427 1.26,0.604 0.188,0.177 10 false *1 1.615,0.427 1.802,0.604 0.188,0.177 10 false *2 0.688,2.49 1.073,2.635 0.385,0.146 10 false ICR+ 2.24,2.5 2.542,2.646 0.302,0.146 10 false ICR-

Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R35-1 (ICL+) - Body ground Ignition switch ON Below 1 V
R35-2 (ICL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R35-1 (ICL+) - R35-2 (ICL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R35-1 (ICL+) - R35-2 (ICL-) Always 1 MΩ or higher
R35-1 (ICL+) - Body ground Always 1 MΩ or higher
R35-2 (ICL-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Curtain Shield Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


OK

9.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK CENTER AIRBAG SENSOR
a.
C207519E03
1.562,1.619 1.746,1.775 0.184,0.156 10 *2 0.817,0.828 1.001,0.984 0.184,0.156 10 *1 1.024,1.252 1.161,1.417 0.137,0.165 10 D 1.172,1.252 1.310,1.417 0.137,0.165 10 C

Connect the connectors to the curtain shield airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor



OK

NG