Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655/37  Seat Belt Buckle Switch RH Circuit Malfunction  


DESCRIPTION

The seat belt buckle switch RH circuit consists of the center airbag sensor and front seat inner belt RH.

DTC B1655/37 is stored when a malfunction is detected in the seat belt buckle switch RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1655/37 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch RH circuit for 2 seconds.

·

A front seat inner belt RH malfunction.

·

A center airbag sensor malfunction.


·

Harness and connector

·

Front seat inner belt assembly RH (Seat belt buckle switch RH)

·

Center airbag sensor assembly



WIRING DIAGRAM

C217039E04
5.471,1.038 5.775,1.191 0.304,0.152 10 15*2 5.471,2.614 5.778,2.767 0.307,0.152 10 14*2 5.123,2.614 5.444,2.767 0.321,0.152 10 12*1 5.123,1.038 5.432,1.191 0.309,0.152 10 11*1 2.437,1.137 2.558,1.307 0.121,0.170 10 2 2.437,2.706 2.558,2.876 0.121,0.170 10 1 1.964,1.12 2.384,1.276 0.420,0.156 10 RBE+ 1.964,2.942 2.363,3.091 0.399,0.149 10 RBE- 5.873,2.823 6.272,2.972 0.399,0.149 10 RBE- 5.506,2.816 5.787,2.965 0.281,0.149 10 Q1 5.506,1.251 5.787,1.400 0.281,0.149 10 Q1 5.154,1.251 5.435,1.400 0.281,0.149 10 R1 5.154,2.822 5.435,2.971 0.281,0.149 10 R1 0.411,3.802 0.720,3.951 0.308,0.149 10 Q34 5.873,1.233 6.279,1.402 0.406,0.170 10 RBE+ 0.409,3.95 1.974,4.099 1.566,0.149 10 Front Seat Inner Belt RH 0.409,4.276 1.974,4.425 1.566,0.149 10 *1: for 5 Door 0.409,4.514 1.974,4.663 1.566,0.149 10 *2: for 3 Door 5.606,3.827 6.992,4.004 1.385,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

OK:

The connectors are properly connected.


Result
Result Proceed to
NG A
OK (for 3 Door) B
OK (for 5 Door) C



C

3.CHECK CONNECTORS

A

CONNECT CONNECTORS PROPERLY

B

8.CHECK CONNECTORS
3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt RH.


b.
C215710E01
0.354,1.359 0.524,1.536 0.170,0.177 10 *1 2.133,1.497 2.303,1.673 0.170,0.177 10 *2

Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

NG

REPLACE HARNESS AND CONNECTOR

4.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U170171E02
6.208,1.156 6.583,1.458 false 6.073,1.156 5.406,1.458 false 3.427,1.042 3.146,1.198 false 3.771,1.042 4.052,1.208 false 0.188,1.333 0.354,1.5 0.167,0.167 10 false *1 1.427,1.396 1.594,1.563 0.167,0.167 10 false *2 1.573,0.906 1.698,1.052 0.125,0.146 10 false A 1.25,1.115 1.375,1.26 0.125,0.146 10 false B 0.927,1.115 1.052,1.26 0.125,0.146 10 false C 0.583,0.906 0.708,1.052 0.125,0.146 10 false D 4.063,1.156 4.448,1.323 0.385,0.167 10 false RBE+ 2.792,1.146 3.177,1.313 0.385,0.167 10 false RBE- 3.5,0.188 3.677,0.344 0.177,0.156 10 false *a 4.021,0.5 4.198,0.667 0.177,0.167 10 false *3 2.75,0.479 3.052,0.635 0.302,0.156 10 false Q34 6.604,1.385 6.99,1.552 0.385,0.167 10 false RBE+ 5.042,1.385 5.427,1.552 0.385,0.167 10 false RBE- 5.865,0.188 6.042,0.344 0.177,0.156 10 false *b 6.5,0.5 6.677,0.667 0.177,0.167 10 false *4 5.135,0.49 5.365,0.646 0.229,0.156 10 false R1

Text in Illustration
*1 Front Seat Inner Belt RH *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Front Seat Inner Belt RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q34-2 (RBE+) - Body ground Ignition switch ON Below 1 V
Q34-1 (RBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q34-2 (RBE+) - R1-11 (RBE+) Always Below 1 Ω
Q34-1 (RBE-) - R1-12 (RBE-) Always Below 1 Ω
Q34-2 (RBE+) - Body ground Always 1 MΩ or higher
Q34-1 (RBE-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE HARNESS AND CONNECTOR

5.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the connectors to the center airbag sensor and front seat inner belt RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

7.CHECK CENTER AIRBAG SENSOR
7.CHECK CENTER AIRBAG SENSOR
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt RH.


b.
C208245E01
0.329,1.707 0.522,1.875 0.193,0.167 10 *1 2.111,1.707 2.304,1.875 0.193,0.167 10 *2

Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

9.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

NG

REPLACE HARNESS AND CONNECTOR

9.CHECK HARNESS AND CONNECTOR (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U170173E01
0.368,1.317 0.531,1.480 0.163,0.163 10 *1 1.608,1.163 1.771,1.325 0.163,0.163 10 *2 1.748,0.875 1.876,1.024 0.128,0.149 10 A 1.426,1.1 1.554,1.249 0.128,0.149 10 B 1.104,1.1 1.232,1.249 0.128,0.149 10 C 0.768,0.889 0.896,1.038 0.128,0.149 10 D 4.252,1.146 4.637,1.309 0.385,0.163 10 RBE+ 2.949,1.128 3.334,1.290 0.385,0.163 10 RBE- 3.682,0.168 3.859,0.324 0.177,0.156 10 *a 4.207,0.483 4.384,0.646 0.177,0.163 10 *3 2.933,0.448 3.216,0.604 0.283,0.156 10 Q34 5.194,1.37 5.579,1.533 0.385,0.163 10 RBE+ 6.776,1.374 7.161,1.537 0.385,0.163 10 RBE- 6.05,0.168 6.226,0.324 0.177,0.156 10 *b 6.68,0.483 6.857,0.646 0.177,0.163 10 *4 5.31,0.452 5.532,0.608 0.222,0.156 10 Q1 5.979,1.187 6.76,1.439 false 5.841,1.187 5.585,1.441 false 3.613,1.023 3.323,1.181 false 3.949,1.023 4.229,1.191 false

Text in Illustration
*1 Front Seat Inner Belt RH *2 Center Airbag Sensor
*3 Connector C *4 Connector B
*a Front view of wire harness connector
(to Front Seat Inner Belt RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q34-2 (RBE+) - Body ground Ignition switch ON Below 1 V
Q34-1 (RBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q34-2 (RBE+) - Q1-15 (RBE+) Always Below 1 Ω
Q34-1 (RBE-) - Q1-14 (RBE-) Always Below 1 Ω
Q34-2 (RBE+) - Body ground Always 1 MΩ or higher
Q34-1 (RBE-) - Body ground Always 1 MΩ or higher




OK

10.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE HARNESS AND CONNECTOR

10.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)
a.
C171812E03
0.666,1.37 0.817,1.539 0.151,0.170 10 *1 1.801,1.37 1.993,1.539 0.192,0.170 10 *2

Connect the connectors to the center airbag sensor and the front seat inner belt RH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

NG

11.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
11.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt RH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

12.CHECK CENTER AIRBAG SENSOR
12.CHECK CENTER AIRBAG SENSOR
a.
C171812E03
0.666,1.37 0.817,1.539 0.151,0.170 10 *1 1.801,1.37 1.993,1.539 0.192,0.170 10 *2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG