Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1633/81  Rear Airbag Sensor Assembly RH Initialization Incomplete  B1638/82  Rear Airbag Sensor Assembly LH Initialization Incomplete  


DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat side airbag LH or RH and curtain shield airbag LH or RH) is composed of the center airbag sensor, side airbag sensor LH or RH and rear airbag sensor LH or RH.

The rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1633 or B1638 is stored when a malfunction is detected in the circuit for the rear collision sensor LH or RH (to determine deployment of the curtain shield airbag LH or RH).

DTC Code DTC Detection Condition Trouble Area
B1633/81 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the rear collision sensor RH (to determine deployment of the curtain shield airbag RH) for 2 seconds.

·

A rear airbag sensor RH malfunction.

·

A side airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Rear airbag sensor RH

·

Side airbag sensor assembly RH

·

Center airbag sensor assembly


B1638/82 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the rear collision sensor LH (to determine deployment of the curtain shield airbag LH) for 2 seconds.

·

A rear airbag sensor LH malfunction.

·

A side airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Rear airbag sensor LH

·

Side airbag sensor assembly LH

·

Center airbag sensor assembly



WIRING DIAGRAM

C175145E11
1.183,0.99 1.610,1.159 0.427,0.170 10 BBR+ 0.084,0.029 1.094,0.199 1.010,0.170 12 for RH Side: 1.695,0.899 1.858,1.069 0.163,0.170 10 4 5.473,0.899 5.622,1.069 0.149,0.170 10 8 5.417,1.707 5.622,1.877 0.204,0.170 10 11 1.695,1.698 1.858,1.868 0.163,0.170 10 3 1.695,3.085 1.858,3.255 0.163,0.170 10 1 3.657,3.085 3.820,3.255 0.163,0.170 10 2 1.695,3.869 1.858,4.039 0.163,0.170 10 2 3.663,3.869 3.826,4.039 0.163,0.170 10 1 2.697,2.945 2.860,3.115 0.163,0.170 10 1 2.703,3.729 2.866,3.899 0.163,0.170 10 2 1.183,1.788 1.610,1.958 0.427,0.170 10 BBR- 5.685,0.99 6.112,1.159 0.427,0.170 10 BBR+ 5.685,1.788 6.112,1.958 0.427,0.170 10 BBR- 1.183,3.193 1.610,3.363 0.427,0.170 10 BCR+ 0.536,4.681 0.783,4.850 0.246,0.170 10 Q4 0.529,4.849 2.058,5.019 1.529,0.170 10 Rear Airbag Sensor RH 3.627,4.681 3.935,4.850 0.309,0.170 10 J8 3.606,4.849 5.412,5.019 1.806,0.170 10 Side Airbag Sensor RH 5.636,4.681 5.945,4.850 0.309,0.170 10 Q1 5.629,4.849 7.026,5.019 1.397,0.170 10 Center Airbag Sensor 3.887,3.193 4.314,3.363 0.427,0.170 10 BCR+ 2.606,3.193 2.901,3.363 0.295,0.170 10 JQ1 2.606,3.971 2.901,4.141 0.295,0.170 10 JQ1 1.183,3.964 1.610,4.134 0.427,0.170 10 BCR- 3.901,3.964 4.328,4.134 0.427,0.170 10 BCR-

C175145E12
1.183,0.99 1.610,1.159 0.427,0.170 10 BBL+ 0.084,0.029 1.094,0.199 1.010,0.170 12 for LH Side: 1.695,0.899 1.858,1.069 0.163,0.170 10 4 5.492,0.899 5.623,1.069 0.130,0.170 10 8 5.417,1.707 5.622,1.877 0.204,0.170 10 15 1.695,1.698 1.858,1.868 0.163,0.170 10 3 1.695,3.085 1.858,3.255 0.163,0.170 10 1 3.657,3.085 3.820,3.255 0.163,0.170 10 2 1.695,3.869 1.858,4.039 0.163,0.170 10 2 3.663,3.869 3.826,4.039 0.163,0.170 10 1 2.697,2.945 2.860,3.115 0.163,0.170 10 2 2.703,3.729 2.866,3.899 0.163,0.170 10 1 1.183,1.788 1.610,1.958 0.427,0.170 10 BBL- 5.685,0.99 6.112,1.159 0.427,0.170 10 BBL+ 5.685,1.788 6.112,1.958 0.427,0.170 10 BBL- 1.183,3.193 1.610,3.363 0.427,0.170 10 BCL+ 0.536,4.681 0.783,4.850 0.246,0.170 10 R4 0.529,4.849 2.058,5.019 1.529,0.170 10 Rear Airbag Sensor LH 3.616,4.681 3.925,4.850 0.309,0.170 10 K8 3.595,4.849 5.386,5.019 1.791,0.170 10 Side Airbag Sensor LH 5.641,4.681 5.949,4.850 0.309,0.170 10 R1 5.634,4.849 7.030,5.019 1.397,0.170 10 Center Airbag Sensor 3.887,3.193 4.314,3.363 0.427,0.170 10 BCL+ 2.594,3.181 2.926,3.351 0.332,0.170 10 KR1 2.594,3.961 2.926,4.131 0.332,0.170 10 KR1 1.183,3.964 1.610,4.134 0.427,0.170 10 BCL- 3.901,3.964 4.328,4.134 0.427,0.170 10 BCL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. The malfunctioning area can be identified by turning the ignition switch off and then to ON again.



b.

Turn the ignition switch to ON, and wait for at least 60 seconds.


c.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633 and B1638 are not output A
DTC B1638 is output B
DTC B1633 is output C

HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.




C

2.CHECK CONNECTION OF CONNECTORS

A

B

7.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor RH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and rear airbag sensor RH.


b.
C208245E01
0.329,1.707 0.522,1.875 0.193,0.167 10 *1 2.111,1.707 2.304,1.875 0.193,0.167 10 *2

Check that the connectors (on the center airbag sensor side and rear airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Center Airbag Sensor



OK

4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR RH)

NG

REPLACE FLOOR WIRE

4.CHECK FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U148407E01
0.512,0.839 0.668,1.005 0.156,0.165 10 D 0.847,1.022 0.998,1.173 0.151,0.151 10 C 1.356,1.019 1.494,1.170 0.137,0.151 10 B 1.713,0.835 1.845,1.009 0.133,0.174 10 A 2.74,0.706 2.966,0.875 0.227,0.170 10 Q4 5.163,0.706 5.392,0.875 0.230,0.170 10 Q1 2.989,1.353 3.402,1.502 0.413,0.149 10 BBR+ 3.881,1.349 4.294,1.498 0.413,0.149 10 BBR- 5.026,1.166 5.438,1.315 0.413,0.149 10 BBR+ 6.705,0.934 7.118,1.083 0.413,0.149 10 BBR- 3.515,0.854 3.179,1.325 false 3.585,0.854 3.949,1.325 false 6.092,0.91 5.45,1.21 false 6.403,1.091 6.681,0.987 false 6.588,1.172 6.588,1.3 false 0.279,1.277 0.463,1.451 0.184,0.174 10 *1 1.341,0.37 1.524,0.544 0.184,0.174 10 *3 1.698,1.274 1.873,1.453 0.175,0.179 10 *2 3.502,0.102 3.686,0.277 0.184,0.174 10 *a 4.364,0.615 4.538,0.794 0.175,0.179 10 *4 6.505,1.324 6.679,1.503 0.175,0.179 10 *6 5.956,0.102 6.140,0.277 0.184,0.174 10 *b 6.862,0.615 7.036,0.794 0.175,0.179 10 *5 1.155,0.853 1.155,0.427 1.155,0.427 1.313,0.427 false

Text in Illustration
*1 Rear Airbag Sensor RH *2 Center Airbag Sensor
*3 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Rear view of wire harness connector
(to Rear Airbag Sensor RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q4-4 (BBR+) - Body ground Ignition switch ON Below 1 V
Q4-3 (BBR-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 8 (BBR+) and 11 (BBR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-4 (BBR+) - Q4-3 (BBR-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q4-4 (BBR+) - Q4-3 (BBR-) Always 1 MΩ or higher
Q4-4 (BBR+) - Body ground Always 1 MΩ or higher
Q4-3 (BBR-) - Body ground Always 1 MΩ or higher




OK

5.CHECK REAR AIRBAG SENSOR RH

NG

REPLACE FLOOR WIRE

5.CHECK REAR AIRBAG SENSOR RH
a.
C171812E03
0.666,1.37 0.817,1.539 0.151,0.170 10 *1 1.801,1.37 1.993,1.539 0.192,0.170 10 *2

Connect the connector to the center airbag sensor.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633 and B1638 are not output A
DTC B1638 is output (for 3 Door) B
DTC B1638 is output (for 5 Door) C
DTC B1633 is output D

HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Center Airbag Sensor


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.



D

6.CHECK SIDE AIRBAG SENSOR RH

A

B

C

6.CHECK SIDE AIRBAG SENSOR RH
a.
C171828E15
0.469,1.49 0.635,1.649 0.165,0.158 10 *1 2.141,1.49 2.304,1.656 0.163,0.165 10 *2

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633 and B1638 are not output A
DTC B1638 is output B
DTC B1633 is output C

HINT:

Codes other than DTC B1643, B1693 and B1698 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Airbag Sensor LH
*2 Rear Airbag Sensor RH


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the side airbag sensor LH and RH to their original positions and connect the connectors to them.



C

A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH

7.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and rear airbag sensor LH.

OK:

The connectors are properly connected.




OK

8.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

8.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and rear airbag sensor LH.


b.
C215710E01
0.354,1.359 0.524,1.536 0.170,0.177 10 *1 2.133,1.497 2.303,1.673 0.170,0.177 10 *2

Check that the connectors (on the center airbag sensor side and rear airbag sensor LH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Rear Airbag Sensor LH
*2 Center Airbag Sensor



OK

9.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - REAR AIRBAG SENSOR LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U148408E01
0.512,0.609 0.668,0.775 0.156,0.165 10 D 0.847,0.792 0.998,0.943 0.151,0.151 10 C 1.356,0.789 1.494,0.940 0.137,0.151 10 B 1.713,0.611 1.845,0.786 0.133,0.174 10 A 5.167,0.59 5.396,0.760 0.230,0.170 10 R1 2.989,1.354 3.402,1.503 0.413,0.149 10 BBL+ 3.881,1.349 4.294,1.498 0.413,0.149 10 BBL- 4.803,1.281 5.216,1.430 0.413,0.149 10 BBL- 6.581,1.281 6.994,1.430 0.413,0.149 10 BBL+ 3.515,0.854 3.179,1.326 false 3.585,0.854 3.949,1.326 false 5.755,1.112 5.139,1.36 false 6.107,0.885 6.546,1.315 false 5.576,1.154 5.576,1.282 false 0.204,1.062 0.388,1.236 0.184,0.174 10 *1 1.346,1.077 1.530,1.251 0.184,0.174 10 *3 1.642,1.156 1.817,1.335 0.175,0.179 10 *2 3.502,0.103 3.686,0.277 0.184,0.174 10 *a 4.364,0.616 4.538,0.795 0.175,0.179 10 *4 5.493,1.305 5.667,1.485 0.175,0.179 10 *6 5.956,0 6.140,0.174 0.184,0.174 10 *b 6.862,0.504 7.036,0.683 0.175,0.179 10 *5 1.155,0.734 1.155,1.159 1.155,1.159 1.313,1.159 false 2.743,0.709 2.962,0.857 0.218,0.149 10 R4

Text in Illustration
*1 Rear Airbag Sensor LH *2 Center Airbag Sensor
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Rear view of wire harness connector
(to Rear Airbag Sensor LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R4-4 (BBL+) - Body ground Ignition switch ON Below 1 V
R4-3 (BBL-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 8 (BBL+) and 15 (BBL-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-4 (BBL+) - R4-3 (BBL-) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R4-4 (BBL+) - R4-3 (BBL-) Always 1 MΩ or higher
R4-4 (BBL+) - Body ground Always 1 MΩ or higher
R4-3 (BBL-) - Body ground Always 1 MΩ or higher




OK

10.CHECK REAR AIRBAG SENSOR LH

NG

REPLACE NO. 2 FLOOR WIRE

10.CHECK REAR AIRBAG SENSOR LH
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the connector to the center airbag sensor.


b.

Interchange the rear airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 90 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633 and B1638 are not output A
DTC B1633 is output (for 3 Door) B
DTC B1633 is output (for 5 Door) C
DTC B1638 is output D

HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Rear Airbag Sensor RH
*2 Center Airbag Sensor


i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.



D

11.CHECK SIDE AIRBAG SENSOR LH

A

B

C

11.CHECK SIDE AIRBAG SENSOR LH
a.
C171828E15
0.469,1.49 0.635,1.649 0.165,0.158 10 *1 2.141,1.49 2.304,1.656 0.163,0.165 10 *2

Interchange the side airbag sensor LH with RH and connect the connectors to them.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 90 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1633 and B1638 are not output A
DTC B1633 is output B
DTC B1638 is output C

HINT:

Codes other than DTC B1633 and B1638 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Side Airbag Sensor RH
*2 Rear Airbag Sensor LH


h.

Turn the ignition switch off.


i.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


j.

Return the side airbag sensor RH and LH to their original positions and connect the connectors to them.



C

A

B

REPLACE SIDE AIRBAG SENSOR ASSEMBLY LH