Wear protective gloves. Sharp areas on the parts may injure your hands.
Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is replaced with a new one.
Initialization (initial position reset) of the fold seat control ECU is performed.
Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).
The fold seat control ECU is exchanged with one from another vehicle.
The seatback frame and seat leg are inspected.
The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.
The seatback frame or seat leg is replaced.
The cable is disconnected from the battery while the seatback or seat cushion is operating.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
73949
1.REMOVE CAP
Remove the 2 caps.
71693
2.REMOVE REAR SEAT CUSHION LOWER HINGE COVER LH
Remove the 2 screws.
Detach the 3 claws and remove the cover.
71693
3.REMOVE REAR SEAT CUSHION LOWER HINGE COVER RH
Remove the 2 screws.
| *1 | Guide |
Detach the 2 claws and guide and remove the cover.
73590
4.REMOVE REAR NO. 2 SEAT INNER BELT ASSEMBLY LH
89715
5.REMOVE FOLD SEAT CONTROL ECU
71827B
6.REMOVE REAR SEAT NO. 1 CUSHION MOULDING
Using a clip remover, remove the 2 clips.
Detach the 2 claws and 4 guides and remove the moulding.
| *1 | Guide |
7.REMOVE SEAT CUSHION COVER WITH PAD
Open the 2 fasteners.
| *1 | Fastener |
Remove the 2 clips and open the under part of the seat cushion cover.
Detach the 2 hooks and remove the seat cushion cover with pad.
| *1 | Hook |
79032
8.REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH
Detach the fastener.
| *1 | Fastener |
Remove the hog rings and seat cushion cover.
71647F
9.REMOVE REAR SEAT CUSHION INNER EDGE PROTECTOR LH
Cut off the tack pins and remove the protector from the cushion pad.
| *1 | Tack Pin |
71827B
10.REMOVE REAR SEAT NO. 2 CUSHION MOULDING
Remove the 2 screws.
Detach the 2 claws and remove the moulding.
79384A
11.REMOVE REAR SEAT NO. 3 LEG COVER LH
Detach the 2 claws and remove the cover.
71694E
12.REMOVE REAR SEAT CUSHION INNER HINGE COVER LH
Remove the screw and clip.
| *1 | Guide |
Detach the guide and remove the cover.
71694E
13.REMOVE REAR SEAT CUSHION INNER HINGE COVER RH
Remove the screw and clip.
| *1 | Guide |
Detach the guide and remove the cover.
72152
14.REMOVE LOWER SEAT TRACK RAIL LH
Remove the 2 bolts and seat track rail.
71702C
15.REMOVE REAR SEATBACK BOARD SUB-ASSEMBLY LH
Detach the 7 clips and remove the board.
72635B
16.REMOVE REAR SEATBACK LOCK HOOK
Remove the lock hook.
71865
17.REMOVE REAR SEAT NO. 1 COVER BEZEL
Remove the 2 screws, detach the guide and remove the bezel.
| *1 | Guide |
18.REMOVE SEATBACK COVER WITH PAD
Detach the hooks.
| *1 | Hook |
Detach the 8 clips and remove the seatback cover with pad.
79034
19.REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH
Remove the hog rings and seatback cover.
71587C
20.REMOVE REAR NO. 2 SEATBACK EDGE PROTECTOR
Cut off the tack pins and remove the protector from the seatback pad.
| *1 | Tack Pin |
79962
21.REMOVE NO. 2 SEATBACK COVER
Detach the 2 claws and remove the cover.
71970A
22.REMOVE REAR SEAT HEADREST COVER
Remove the 2 screws.
| *1 | Guide |
Detach the 2 claws and guide and remove the cover.
71987A
23.REMOVE REAR SEAT HEADREST CABLE
Detach the 2 clamps.
| *1 | Cable End |
| *2 | Clamp |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
71970
24.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the 3 nuts and headrest.
71587C
25.REMOVE REAR SEATBACK EDGE PROTECTOR
Detach the 4 claws and remove the 2 protectors.
71834C
26.REMOVE REAR NO. 3 SEAT INNER RECLINING COVER LH
Detach the 4 claws and remove the cover.
71834C
27.REMOVE REAR NO. 3 SEAT OUTER RECLINING COVER LH
Remove the screw.
| *1 | Guide |
Detach the guide and 2 claws and remove the cover.
79202
28.REMOVE NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH
Remove the bolt and disconnect the wire harness.
Using a screwdriver, release the lock lever as shown in the illustration.
Retract the seat cushion frame.
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts and seat cushion frame.
79384
29.REMOVE REAR SEAT LEG COVER LH
Remove the clip.
| *1 | Hook |
Detach the 3 hooks and 5 clips and remove the cover.
72906
30.REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH
Remove the 3 clips.
| *1 | Guide |
Detach the 2 claws and 4 guides and remove the 3rd seat link.
71844C
31.REMOVE REAR NO. 2 SEAT INNER RECLINING COVER LH
Detach the 5 claws and remove the cover.
71844A
32.REMOVE REAR NO. 2 SEAT OUTER RECLINING COVER LH
Remove the screw.
| *1 | Guide |
Detach the guide and 2 claws and remove the cover.
72690A
33.REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH
Detach the 2 clamps.
| *1 | Clamp |
| *2 | Cable End |
Twist the cable end in the direction indicated by the arrow and remove the cable.
72690A
34.REMOVE REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)
Cut off the 2 cable ties and detach the 3 clamps.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Twist the cable end in the direction indicated by the arrow and remove the cable.
72695C
35.REMOVE REAR SEAT LOCK CONTROL CABLE LH
Detach the 2 clamps.
| *1 | Cable End |
| *2 | Clamp |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
72695B
36.REMOVE REAR SEAT LOCK CONTROL CABLE RH (for RH Side)
Cut off the 2 cable ties and detach the 3 clamps.
| *1 | Cable Tie |
| *2 | Clamp |
| *3 | Cable End |
Twist the 2 cable ends in the direction indicated by the arrow and remove the cable.
79304A
37.REMOVE NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH
Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and frame.
82196
38.REMOVE REAR NO. 2 SEAT WIRE LH
Disconnect the connector.
Detach the wire harness clamps and remove the seat wire.
79040
39.REMOVE NO. 3 SEAT LEG ASSEMBLY LH
Remove the 4 clips and seat cushion under carpet LH from the No. 3 seat leg.
79020B
40.REMOVE NO. 2 SEAT LEG ASSEMBLY (for RH Side)
Remove the 4 clips and seat cushion under carpet RH from the No. 2 seat leg.