Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) › 2015.06–2018.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261105 REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:
·

Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is replaced with a new one.

-

Initialization (initial position reset) of the fold seat control ECU is performed.



·

Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is exchanged with one from another vehicle.

-

The seatback frame and seat leg are inspected.

-

The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

-

The seatback frame or seat leg is replaced.

-

The cable is disconnected from the battery while the seatback or seat cushion is operating.




HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 79040 1.INSTALL NO. 3 SEAT LEG ASSEMBLY LH

a.

Attach the 4 clips to install the seat cushion under carpet LH to the No. 3 seat leg.


Hide 79020B 2.INSTALL NO. 2 SEAT LEG ASSEMBLY (for RH Side)

a.

Attach the 4 clips to install the seat cushion under carpet RH to the No. 2 seat leg.


Hide 82196 3.INSTALL REAR NO. 2 SEAT WIRE LH

a.

Attach the wire harness clamps to install the seat wire.


b.

Connect the connector.


Hide 79304A 4.INSTALL NO. 3 SEATBACK FRAME SUB-ASSEMBLY LH

a.

Using a T45 "TORX" socket wrench, install the seatback frame with the 4 "TORX" bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72695C 5.INSTALL REAR SEAT LOCK CONTROL CABLE LH

a.
B238712E01
0.457,1.918 0.617,2.065 0.161,0.147 10 *2 1.76,2.004 0.652,2.004 false 0.924,1.082 0.924,1.998 false 2.863,1.517 2.465,1.517 false 2.282,1.44 2.459,1.6 0.178,0.16 2.282,1.44 2.442,1.586 0.161,0.147 10 *1 1.121,0.5 1.282,0.647 0.161,0.147 10 *1 0.62,0.967 1.015,0.578 1.015,0.578 1.11,0.578 false

Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration
*1 Cable End
*2 Clamp


b.

Attach the 2 clamps to install the cable.

HINT:
B505967

Install at the middle level of the cable clamp (triple level) side.



Hide 72695B 6.INSTALL REAR SEAT LOCK CONTROL CABLE RH (for RH Side)

a.
B238711E03
2.74,0.896 0.979,0.896 true 1.281,0.74 1.281,0.896 false 2.042,1.219 0.333,1.219 true 1.615,0.469 0.458,0.469 0.458,0.469 0.458,1.208 true 0.521,2.292 0.521,1.208 true 1.854,2.896 1.667,2.625 1.667,2.625 1.552,2.625 true 1.792,1.313 1.438,1.313 true 1.198,0.573 1.344,0.729 0.146,0.156 10 false *1 0.146,1.135 0.292,1.292 0.146,0.156 10 false *2 1.375,2.542 1.542,2.719 0.167,0.177 10 true *3 1.26,1.24 1.417,1.427 0.156,0.188 10 false *3

Twist the 2 cable ends in the direction indicated by the arrow to connect them.

Text in Illustration
*1 Cable Tie
*2 Clamp
*3 Cable End


b.

Attach the 3 clamps to install the cable.

HINT:
B505967

Install at the middle level of the cable clamp (triple level) side.



c.

Install 2 new cable ties.


Hide 72690A 7.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY LH

a.
B238710E01
2.539,2.43 2.692,2.572 0.152,0.142 10 *2 1.242,2.511 2.526,2.511 false 2.161,1.944 2.161,2.507 false 1.444,2.008 1.596,2.150 0.152,0.142 10 *1 0.902,2.408 1.336,2.082 1.336,2.082 1.422,2.082 false

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Cable End
*2 Clamp


b.

Attach the 2 clamps to install the cable.


Hide 72690A 8.INSTALL REAR SEAT LOCK RELEASE STRAP ASSEMBLY RH (for RH Side)

a.
B238709E02
1.5,2.104 2.615,1.958 true 2.25,2.01 2.25,2.125 false 1.896,2.333 0.323,2.333 true 1.823,1.385 0.344,1.385 0.344,1.385 0.344,2.323 true 0.49,1.885 0.333,1.885 true 1.646,2.438 1.219,2.438 true 2.156,2.125 2.313,2.26 0.156,0.135 10 false *1 0.125,2.26 0.292,2.438 0.167,0.177 10 false *2 1.052,2.365 1.219,2.531 0.167,0.167 10 false *3

Twist the cable end in the direction indicated by the arrow to connect it.

Text in Illustration
*1 Cable Tie
*2 Clamp
*3 Cable End


b.

Attach the 3 clamps to install the cable.


c.

Install the 2 new cable ties.


Hide 71844A 9.INSTALL REAR NO. 2 SEAT OUTER RECLINING COVER LH

a.

Attach the 2 claws and guide to install the cover.


b.

Install the screw.


Hide 71844C 10.INSTALL REAR NO. 2 SEAT INNER RECLINING COVER LH

a.

Attach the 5 claws to install the cover.


Hide 72906 11.INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH

a.

Attach the 4 guides and 2 claws to install the seat leg link.


b.

Install the 3 clips.


Hide 79384 12.INSTALL REAR SEAT LEG COVER LH

a.

Attach the 5 clips and 3 hooks, to install the cover.


b.

Install the clip.


Hide 79202 13.INSTALL NO. 2 SEAT CUSHION FRAME SUB-ASSEMBLY LH

a.

Using a T40 "TORX" socket wrench, install the seat cushion frame with the 4 "TORX" bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Pull out the seat cushion frame.


c.

Connect the wire harness with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 71834C 14.INSTALL REAR NO. 3 SEAT OUTER RECLINING COVER LH

a.

Attach the 2 claws and guide to install the cover.


b.

Install the screw.


Hide 71834C 15.INSTALL REAR NO. 3 SEAT INNER RECLINING COVER LH

a.

Attach the 4 claws to install the cover.


Hide 71587C 16.INSTALL REAR SEATBACK EDGE PROTECTOR

a.

Attach the 4 claws to install the 2 protectors.


Hide 71970 17.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the headrest with the 3 nuts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 71987A 18.INSTALL REAR SEAT HEADREST CABLE

a.
B238713E01
1.285,1.543 1.450,1.694 0.165,0.151 10 *2 1.256,1.615 1.153,1.615 1.153,1.615 0.649,1.448 false 1.153,1.615 0.649,1.706 false 2.872,1.125 3.037,1.276 0.165,0.151 10 *1 2.853,1.218 2.741,1.218 2.741,1.218 2.66,0.99 false 0.054,1.809 0.219,1.951 0.165,0.142 10 *1 0.534,1.95 0.336,1.892 0.336,1.892 0.236,1.892 false

Twist the 2 cable ends in the direction indicated by the arrow to install them.

Text in Illustration
*1 Cable End
*2 Clamp


b.

Attach the 2 clamps to install the cable.


Hide 71970A 19.INSTALL REAR SEAT HEADREST COVER

a.

Attach the 2 claws and guide, to install the cover.


b.

Install the 2 screws.


Hide 79962 20.INSTALL NO. 2 SEATBACK COVER

a.

Attach the 2 claws to install the cover.


Hide 71587C 21.INSTALL REAR NO. 2 SEATBACK EDGE PROTECTOR

a.

Install the protector to the seatback pad with new tack pins.


Hide 79034 22.INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

a.

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

B449836E01
1.948,1.698 2.333,0.698 2.333,0.698 2.49,0.698 false 2.563,0.573 2.875,0.771 0.313,0.198 10 false *1

Text in Illustration
*1 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 23.INSTALL SEATBACK COVER WITH PAD

a.

Attach the 8 clips.


b.

Attach the hooks to install the seatback cover with pad.


Hide 71865 24.INSTALL REAR SEAT NO. 1 COVER BEZEL

a.

Pass the strap through the bezel hole.


b.

Attach the guide to install the bezel.


c.

Install the 2 screws.


Hide 72635B 25.INSTALL REAR SEATBACK LOCK HOOK

a.

Install the lock hook.


Hide 71702C 26.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY LH

a.

Attach the 7 clips to install the board.


Hide 72152 27.INSTALL LOWER SEAT TRACK RAIL LH

a.

Install the track rail with the 2 bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 71694E 28.INSTALL REAR SEAT CUSHION INNER HINGE COVER RH

a.

Attach the guide to install the cover.


b.

Install the clip and screw.


Hide 71694E 29.INSTALL REAR SEAT CUSHION INNER HINGE COVER LH

a.

Attach the guide to install the cover.


b.

Install the clip and screw.


Hide 79384A 30.INSTALL REAR NO. 3 SEAT LEG COVER LH

a.

Attach the 2 claws to install the cover.


Hide 71827B 31.INSTALL REAR SEAT NO. 2 CUSHION MOULDING

a.

Attach the 2 claws to install the moulding.


b.

Install the 2 screws.


Hide 71647F 32.INSTALL REAR SEAT CUSHION INNER EDGE PROTECTOR LH

a.

Install the protector to the seat cushion pad with new tack pins.


Hide 79032 33.INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

a.
B238853E01
2.629,2.017 2.794,2.164 0.165,0.147 10 *1 2.021,2.872 1.754,2.872 1.754,2.872 1.858,3.695 false 2.119,1.299 2.119,2.099 2.119,2.099 2.61,2.099 false 2.042,2.791 2.207,2.937 0.165,0.147 10 *2

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

Text in Illustration
*1 Fastener
*2 Hog Ring Pliers

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.

Attach the fastener.


Hide 34.INSTALL SEAT CUSHION COVER WITH PAD

a.

Attach the 2 hooks to install the seat cushion cover with pad.


b.

Attach the 2 hooks.


c.

Attach the 2 hooks to close the cover.


d.

Close the 2 fasteners.


e.

Attach the 2 fasteners.


Hide 71827B 35.INSTALL REAR SEAT NO. 1 CUSHION MOULDING

a.

Attach the 4 guides and 2 claws to install the moulding.


b.

Install the 2 clips.


Hide 73590 37.INSTALL REAR NO. 2 SEAT INNER BELT ASSEMBLY LH

Hide 71693 38.INSTALL REAR SEAT CUSHION LOWER HINGE COVER RH

a.

Attach the 2 claws to install the cover.


b.

Install the 2 screws.


Hide 71693 39.INSTALL REAR SEAT CUSHION LOWER HINGE COVER LH

a.

Attach the guide and 2 claws to install the cover.


b.

Install the 2 screws.


Hide 73949 40.INSTALL CAP

a.

Install the 2 caps.