Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) U

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  TERMINALS OF ECU  


CHECK FRONT POWER SEAT SWITCH (for LHD)


U115555E04
4.167,0.333 4.344,0.49 0.177,0.156 10 false b5 3.167,0.333 3.344,0.49 0.177,0.156 10 false b4

a.

Disconnect the b4 and b5 connectors from the front power seat switch LH.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b4-1 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
b4-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
b4-6 (+B2) - b4-1 (GND2) SB - W-B Power source Always 11 to 14 V
b4-7 (+B) - b4-2 (GND) W - W-B Power source Always 11 to 14 V
b5-12 (SYSB) - b4-2 (GND) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the b4 and b5 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
b4-3 (SLD+) - b4-2 (GND) L - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
b4-4 (SLD-) - b4-2 (GND) GR - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
b4-5 (FRV-) - b4-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
b4-8 (FRV+) - b4-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
b4-9 (RCL+) - b4-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
b4-11 (RCL-) - b4-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
b4-10 (LFT+) - b4-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
b4-12 (LFT-) - b4-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
b5-1 (SGND) - b4-2 (GND) BR - W-B Ground Always Below 1 Ω
b5-3 (SSFV) - b5-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
b5-4 (SSRL) - b5-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
b5-5 (SSRS) - b5-1 (SGND) G- BR Slide position signal Slide function operating 4.5 to 4.8 V
b5-11 (SSRR) - b5-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the front power seat switch may have a malfunction.



CHECK FRONT POWER SEAT SWITCH (for RHD)


U169654E02
2.854,0.333 3.031,0.479 0.177,0.146 10 false a5 3.844,0.333 4.021,0.479 0.177,0.146 10 false a4

a.

Disconnect the a4 and a5 connectors from the front power seat switch RH.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a4-1 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω
a4-2 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
a4-6 (+B2) - a4-1 (GND2) SB - W-B Power source Always 11 to 14 V
a4-7 (+B) - a4-2 (GND) W - W-B Power source Always 11 to 14 V
a5-12 (SYSB) - a4-2 (GND) P - W-B System power source Always 11 to 14 V

If the result is not as specified, there may be a malfunction on the wire harness side.


c.

Reconnect the a4 and a5 switch connectors.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
a4-3 (SLD+) - a4-2 (GND) L - W-B Sliding motor signal (forward) Slide switch off Below 1 V
Slide switch on (Forward) 11 to 14 V
a4-4 (SLD-) - a4-2 (GND) GR - W-B Sliding motor signal (rearward) Slide switch off Below 1 V
Slide switch on (Rearward) 11 to 14 V
a4-5 (FRV-) - a4-2 (GND) R - W-B Front vertical motor signal (downward) Front vertical switch off Below 1 V
Front vertical switch on (Downward) 11 to 14 V
a4-8 (FRV+) - a4-2 (GND) B - W-B Front vertical motor signal (upward) Front vertical switch off Below 1 V
Front vertical switch on (Upward) 11 to 14 V
a4-9 (RCL+) - a4-2 (GND) P - W-B Reclining motor signal (forward) Reclining switch off Below 1 V
Reclining switch on (Forward) 11 to 14 V
a4-11 (RCL-) - a4-2 (GND) LG - W-B Reclining motor signal (rearward) Reclining switch off Below 1 V
Reclining switch on (Rearward) 11 to 14 V
a4-10 (LFT+) - a4-2 (GND) V - W-B Lifter motor signal (upward) Lifter switch off Below 1 V
Lifter switch on (Upward) 11 to 14 V
a4-12 (LFT-) - a4-2 (GND) G - W-B Lifter motor signal (downward) Lifter switch off Below 1 V
Lifter switch on (Downward) 11 to 14 V
a5-1 (SGND) - a4-2 (GND) BR - W-B Ground Always Below 1 Ω
a5-3 (SSFV) - a5-1 (SGND) R - BR Front vertical position signal Front vertical function operating 4.5 to 4.8 V
a5-4 (SSRL) - a5-1 (SGND) P - BR Lifter position signal Lifter function operating 4.5 to 4.8 V
a5-5 (SSRS) - a5-1 (SGND) G - BR Slide position signal Slide function operating 4.5 to 4.8 V
a5-11 (SSRR) - a5-1 (SGND) V - BR Reclining position signal Reclining function operating 4.5 to 4.8 V

If the result is not as specified, the front power seat switch may have a malfunction.



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169674E03
1.625,1.469 1.865,1.219 1.865,1.219 1.948,1.219 false 1.625,1.823 1.865,1.583 1.865,1.583 1.948,1.583 false 1.625,2.135 1.865,1.896 1.865,1.896 1.948,1.896 false 1,1.542 0.656,1.104 0.656,1.104 0.521,1.104 false 0.25,1.031 0.552,1.188 0.302,0.156 10 false 2I*A 0.198,1.188 0.552,1.344 0.354,0.156 10 false 2H*B 1.083,3.865 1.365,4.021 0.281,0.156 10 false G63 0.896,2.167 1.104,2.323 0.208,0.156 10 false 2F 5.865,1.49 6.073,1.646 0.208,0.156 10 false 2D 5.865,2.188 6.073,2.344 0.208,0.156 10 false 2A 1.073,2.708 1.281,2.865 0.208,0.156 10 false 2K 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.958,1.156 2.292,1.302 0.333,0.146 10 false G65 1.958,1.51 2.271,1.656 0.313,0.146 10 false G64 1.958,1.833 2.271,1.979 0.313,0.146 10 false G63 3.583,3.875 3.875,4.031 0.292,0.156 10 false G64 0.594,5.198 0.75,5.354 0.156,0.156 10 false 2I 1.5,5.198 1.708,5.354 0.208,0.156 10 false 2H 1.875,6.417 2.094,6.573 0.219,0.156 10 false 2D 4.927,6.406 5.146,6.563 0.219,0.156 10 false 2A 3.5,7.677 3.635,7.833 0.135,0.156 10 false A 3.948,5.188 4.146,5.344 0.198,0.156 10 false 2F 5.885,5.188 6.083,5.344 0.198,0.156 10 false 2K 5.896,3.885 6.198,4.042 0.302,0.156 10 false G65 0.875,5.198 1.104,5.375 0.229,0.177 10 false *A 1.854,5.198 2.083,5.375 0.229,0.177 10 false *B

Text in Illustration
*A for LHD *B for RHD

a.

b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Power source Always 11 to 14 V
A-32 (IG) - Body ground - Power source (IG) Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A-11 (GND) - Body ground - Body ground Always Below 1 Ω
G63-3 (GND2) - Body ground W-B - Body ground Body ground Always Below 1 Ω

If the result is not as specified, there may be a malfunction on the wire harness side.



d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G63-25 (M1) - Body ground SB - Body ground Memory switch M1 signal Memory switch M1 off Pulse generation (See waveform 1 or 2)
Memory switch M1 on Below 1 V
G63-26 (MM) - Body ground LG - Body ground Memory switch SET signal Memory switch SET off Pulse generation (See waveform 1 or 2)
Memory switch SET on Below 1 V
G63-27 (M2) - Body ground V - Body ground Memory switch M2 signal Memory switch M2 off Pulse generation (See waveform 1 or 2)
Memory switch M2 on Below 1 V
2I-27 (FLCY) - Body ground*1 R - Body ground Front door courtesy light switch LH signal Front door LH closed 11 to 14 V
Front door LH open Below 1 V
2H-26 (FRCY) - Body ground*2 B - Body ground Front door courtesy light switch RH signal Front door RH closed 11 to 14 V
Front door RH open Below 1 V

*1: for LHD

*2: for RHD



e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G63-25 (M1) - Body ground
G63-26 (MM) - Body ground
G63-27 (M2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Memory switch M1 off
Memory switch SET off
Memory switch M2 off


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) G63-25 (M1) - Body ground
G63-26 (MM) - Body ground
G63-27 (M2) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Memory switch M1 off
Memory switch SET off
Memory switch M2 off