Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM › 2015.06–2020.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Park / Neutral Position Switch Circuit  


DESCRIPTION

The fold seat control ECU receives signals from the park/neutral position switch and controls the seat folding and return operations. If the shift lever is in any position other than P when the ignition switch is ON, the seat cannot be operated.

WIRING DIAGRAM

B239510E01
5.829,1.266 5.993,1.468 0.163,0.202 10 P 5.191,1.468 5.347,1.624 0.156,0.156 10 *2 5.531,1.468 5.684,1.627 0.153,0.159 10 *1 0.201,3.344 1.163,3.499 0.962,0.155 10 *2: for RH Side 0.201,2.962 1.144,3.116 0.943,0.153 10 *1: for LH Side 5.561,1.103 5.658,1.265 0.097,0.162 10 6 5.23,1.103 5.327,1.265 0.097,0.162 10 6 5.557,2.88 7.010,3.215 1.453,0.335 10 Fold Seat Control ECU LH*1, RH*2 4.369,1.175 4.467,1.337 0.097,0.162 10 6 3.188,1.175 3.286,1.337 0.097,0.162 10 2 4.091,1.386 4.291,1.536 0.200,0.149 10 PL 3.374,1.386 3.607,1.536 0.232,0.149 10 RB 2.989,1.941 4.776,2.294 1.787,0.353 10 Park/Neutral Position Switch Assembly 2.989,1.774 3.265,1.932 0.276,0.159 10 C33 5.189,1.286 5.355,1.440 0.166,0.154 10 c1 5.519,1.286 5.691,1.440 0.172,0.154 10 d1 0.052,1.276 1.644,1.446 1.592,0.170 10 from ECU-IG NO. 1 Fuse 0.621,1.983 1.649,2.162 1.028,0.178 10 from ACC Fuse

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (PARK/NEUTRAL POSITION SWITCH SIGNAL)
a.
U115626E01
0.093,0.053 0.271,0.235 0.179,0.182 10 *a 1.583,0.51 1.748,0.664 0.165,0.154 10 c1 0.859,0.51 1.035,0.664 0.175,0.154 10 d1 1.629,1.75 1.840,1.925 0.210,0.175 10 P 1.676,1.228 1.676,1.721 false 1.185,0.425 1.352,0.578 0.168,0.153 10 *A 1.898,0.425 2.066,0.579 0.168,0.153 10 *B

Remove the fold seat control ECU with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection Condition Specified Condition
d1-6 (P) - Body ground Ignition switch ACC or ON
Shift lever in P
11 to 14 V
Ignition switch ACC or ON
Shift lever not in P
Below 1 V

for RH Side
Tester Connection Condition Specified Condition
c1-6 (P) - Body ground Ignition switch ACC or ON
Shift lever in P
11 to 14 V
Ignition switch ACC or ON
Shift lever not in P
Below 1 V


Text in Illustration
*A for LH Side
*B for RH Side
*a Component with harness connected
(Fold Seat Control ECU)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
2.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)
a.
U169916E02
2.083,0.385 1.958,0.385 1.958,0.385 1.802,1.01 false 0.094,0.052 0.281,0.219 0.188,0.167 10 false *a 2.125,0.302 2.344,0.448 0.219,0.146 10 false RB 0.396,0.99 0.667,1.146 0.271,0.156 10 false C40

Disconnect the C40 switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C40-2 (RB) - Body ground Ignition switch ACC or ON 11 to 14 V
Ignition switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C208647E05
1.638,1.028 1.507,0.406 1.507,0.406 1.355,0.406 false 1.901,1.312 2.01,1.831 2.01,1.831 2.189,1.831 false 1.081,0.317 1.300,0.469 0.219,0.152 10 RB 2.23,1.743 2.428,1.897 0.198,0.154 10 PL

Disconnect the C40 switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (RB) - 6 (PL) Shift lever in P Below 1 Ω
2 (RB) - 6 (PL) Shift lever not in P 10 kΩ or higher


Result
Result Proceed to
OK A
NG (for AC60F Automatic Transmission) B
NG (for A750F Automatic Transmission) C



A

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - PARK/NEUTRAL POSITION SWITCH)

B

C

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - PARK/NEUTRAL POSITION SWITCH)
a.

Disconnect the d1*1 or c1*2 ECU connector.

*1: for LH Side

*2: for RH Side



b.

Disconnect the C40 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d1-6 (P) - C40-6 (PL) Always Below 1 Ω
d1-6 (P) - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
c1-6 (P) - C40-6 (PL) Always Below 1 Ω
c1-6 (P) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR