Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Fold Seat Switch Circuit  


DESCRIPTION

When the fold seat switch is operated, a switch operation signal is sent to the fold seat control ECU. The ECU receives switch operation signals from each switch and activates the reclining motor and cushion motor.

WIRING DIAGRAM

B239514E01
5.06,4.445 6.512,4.763 1.452,0.318 10 Fold Seat Control ECU LH*1, RH*2 5.286,3.697 5.668,3.855 0.382,0.159 10 RTN2 5.286,3.027 5.652,3.187 0.365,0.161 10 FLD2 1.3,4.628 3.383,4.804 2.083,0.176 10 No. 1 Fold Seat Switch Assembly 2.763,1.343 3.172,1.491 0.409,0.149 10 RTRN 2.775,0.663 3.172,0.813 0.398,0.150 10 FOLD 4.634,3.516 4.815,3.672 0.181,0.156 10 14 4.959,3.697 5.139,3.852 0.180,0.155 10 d1 4.64,3.697 4.817,3.852 0.177,0.156 10 c1 1.587,1.343 1.753,1.508 0.165,0.165 10 E 1.3,2.143 3.380,2.309 2.080,0.166 10 No. 2 Fold Seat Switch Assembly 5.286,0.558 5.683,0.714 0.396,0.156 10 FOLD 5.286,1.228 5.701,1.384 0.415,0.156 10 RTRN 4.977,3.88 5.132,4.036 0.155,0.156 10 *1 4.96,3.516 5.141,3.672 0.181,0.156 10 14 4.647,3.88 4.802,4.036 0.155,0.156 10 *2 4.635,2.846 4.816,3.002 0.181,0.156 10 10 4.96,3.027 5.139,3.182 0.180,0.155 10 d1 4.64,3.027 4.818,3.183 0.177,0.156 10 c1 4.978,3.21 5.133,3.366 0.155,0.156 10 *1 4.961,2.846 5.142,3.002 0.181,0.156 10 10 4.648,3.21 4.803,3.366 0.155,0.156 10 *2 4.635,1.047 4.817,1.203 0.181,0.156 10 15 4.96,1.228 5.139,1.383 0.180,0.155 10 d1 4.641,1.228 4.818,1.383 0.177,0.156 10 c1 4.978,1.411 5.133,1.567 0.155,0.156 10 *1 4.961,1.047 5.142,1.203 0.181,0.156 10 15 4.648,1.411 4.803,1.567 0.155,0.156 10 *2 4.636,0.377 4.817,0.533 0.181,0.156 10 16 4.96,0.558 5.140,0.713 0.180,0.155 10 d1 4.641,0.558 4.818,0.714 0.177,0.156 10 c1 4.979,0.741 5.134,0.897 0.155,0.156 10 *1 4.962,0.377 5.143,0.533 0.181,0.156 10 16 4.649,0.741 4.804,0.897 0.155,0.156 10 *2 3.271,0.298 3.503,0.451 0.232,0.154 10 8*1 3.271,0.448 3.503,0.602 0.232,0.154 10 6*2 3.271,0.967 3.503,1.121 0.232,0.154 10 3*1 3.271,1.117 3.503,1.271 0.232,0.154 10 1*2 1.389,1.117 1.485,1.274 0.096,0.157 10 7 1.3,1.949 1.593,2.110 0.293,0.161 10 R12 1.3,4.438 2.253,4.599 0.953,0.162 10 Q11*1, R33*2 2.652,3.815 3.167,3.964 0.515,0.149 10 RTNL*1 2.674,3.135 3.165,3.285 0.491,0.150 10 FLDL*1 1.588,3.815 1.753,3.980 0.165,0.165 10 E 3.271,2.77 3.503,2.924 0.232,0.154 10 6*1 3.271,2.92 3.503,3.074 0.232,0.154 10 8*2 3.271,3.439 3.503,3.593 0.232,0.154 10 1*1 3.271,3.59 3.503,3.743 0.232,0.154 10 3*2 1.389,3.59 1.485,3.747 0.096,0.157 10 7 2.647,3.411 3.165,3.561 0.518,0.150 10 FLDR*2 2.629,4.082 3.164,4.231 0.535,0.149 10 RTNR*2 0.19,5.051 1.162,5.218 0.972,0.167 10 *1: for LH Side 0.19,5.407 1.162,5.574 0.972,0.167 10 *2: for RH Side

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU (FOLD SEAT SWITCH SIGNAL)
a.

Check the No. 1 fold seat switch signal.

i.
U115627E01
0.095,0.076 0.273,0.246 0.179,0.170 10 *a 0.959,0.499 1.134,0.655 0.175,0.155 10 d1 1.298,0.404 1.468,0.560 0.169,0.156 10 *A 1.64,0.498 1.813,0.653 0.172,0.155 10 c1 1.971,0.403 2.140,0.559 0.169,0.156 10 *B 1.611,1.828 1.984,1.980 0.373,0.152 10 FLD2 0.412,1.828 0.811,1.980 0.400,0.152 10 RTN2 1.377,1.266 1.812,1.672 1.812,1.672 1.812,1.794 false 1.076,1.266 0.641,1.672 0.641,1.672 0.641,1.794 false

Remove the fold seat control ECU with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection Condition Specified Condition
d1-10 (FLD2) - Body ground No. 1 fold seat switch LH off 11 to 14 V
No. 1 fold seat switch LH fold Below 1 V
d1-14 (RTN2) - Body ground No. 1 fold seat switch LH off 11 to 14 V
No. 1 fold seat switch LH return Below 1 V

for RH Side
Tester Connection Condition Specified Condition
c1-10 (FLD2) - Body ground No. 1 fold seat switch RH off 11 to 14 V
No. 1 fold seat switch RH fold Below 1 V
c1-14 (RTN2) - Body ground No. 1 fold seat switch RH off 11 to 14 V
No. 1 fold seat switch RH return Below 1 V




b.

Check No. 2 fold seat switch signal.

i.
U115628E01
0.089,0.072 0.268,0.242 0.179,0.170 10 *a 0.963,0.492 1.136,0.648 0.172,0.155 10 d1 1.298,0.397 1.468,0.553 0.171,0.156 10 *A 1.645,0.491 1.809,0.646 0.164,0.155 10 c1 1.973,0.396 2.143,0.552 0.171,0.156 10 *B 1.576,1.791 1.997,1.943 0.420,0.152 10 RTRN 0.44,1.791 0.840,1.943 0.400,0.152 10 FOLD 1.003,1.259 1.777,1.635 1.777,1.635 1.777,1.758 false 0.926,1.259 0.67,1.635 0.67,1.635 0.67,1.758 false

Remove the fold seat control ECU with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH Side
Tester Connection Condition Specified Condition
d1-15 (RTRN) - Body ground No. 2 fold seat switch LH off 11 to 14 V
No. 2 fold seat switch LH return Below 1 V
d1-16 (FOLD) - Body ground No. 2 fold seat switch LH off 11 to 14 V
No. 2 fold seat switch LH fold Below 1 V

for RH Side
Tester Connection Condition Specified Condition
c1-15 (RTRN) - Body ground No. 2 fold seat switch RH off 11 to 14 V
No. 2 fold seat switch RH return Below 1 V
c1-16 (FOLD) - Body ground No. 2 fold seat switch RH off 11 to 14 V
No. 2 fold seat switch RH fold Below 1 V


Text in Illustration
*A for LH Side
*B for RH Side
*a Component with harness connected
(Fold Seat Control ECU)

Result
Result Proceed to
OK A
NG (No. 1 fold seat switch signal) B
NG (No. 2 fold seat switch signal) C




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY

C

4.INSPECT NO. 2 FOLD SEAT SWITCH ASSEMBLY
2.INSPECT NO. 1 FOLD SEAT SWITCH ASSEMBLY
a.
B239689E01
2.486,0.999 3.029,1.165 0.543,0.165 10 RTNL*A 2.537,1.762 3.080,1.927 0.543,0.165 10 FLDL*A 0.243,0.424 0.815,0.590 0.571,0.165 10 RTNR*B 0.342,1.2 0.885,1.365 0.543,0.165 10 FLDR*B 1.58,1.74 1.702,1.897 0.121,0.157 10 E 2.038,1.083 2.432,1.083 false 1.025,1.284 1.419,1.284 false 1.588,1.012 1.082,0.505 1.082,0.505 0.961,0.505 false 1.861,1.341 2.368,1.847 2.368,1.847 2.488,1.847 false 1.637,1.351 1.637,1.708 false

Remove the No. 1 fold seat switch (See page Vehicle Interior>SEAT>POWER SEAT SWITCH(for Rear No. 2 Seat)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Switch Condition Specified Condition
6 (FLDL) - 7 (E) No. 1 fold seat switch LH fold Below 1 Ω
No. 1 fold seat switch LH off 10 kΩ or higher
1 (RTNL) - 7 (E) No. 1 fold seat switch LH return Below 1 Ω
No. 1 fold seat switch LH off 10 kΩ or higher

for RH Side
Tester Connection Switch Condition Specified Condition
8 (FLDR) - 7 (E) No. 1 fold seat switch RH fold Below 1 Ω
No. 1 fold seat switch RH off 10 kΩ or higher
3 (RTNR) - 7 (E) No. 1 fold seat switch RH return Below 1 Ω
No. 1 fold seat switch RH off 10 kΩ or higher


Text in Illustration
*A for LH Side
*B for RH Side



OK

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 FOLD SEAT SWITCH)

NG

REPLACE NO. 1 FOLD SEAT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 1 FOLD SEAT SWITCH)

*1: for LH Side

*2: for RH Side


a.

Disconnect the d1*1 or c1*2 ECU connector.


b.

Disconnect the Q11*1 or R33*2 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d1-10 (FLD2) - Q11-6 (FLDL) Always Below 1 Ω
d1-10 (FLD2) - Body ground Always 10 kΩ or higher
d1-14 (RTN2) - Q11-1 (RTNL) Always Below 1 Ω
d1-14 (RTN2) - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
c1-10 (FLD2) - R33-8 (FLDR) Always Below 1 Ω
c1-10 (FLD2) - Body ground Always 10 kΩ or higher
c1-14 (RTN2) - R33-3 (RTNR) Always Below 1 Ω
c1-14 (RTN2) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT NO. 2 FOLD SEAT SWITCH ASSEMBLY
a.
B239689E02
2.486,0.999 3.074,1.165 0.587,0.165 10 RTRN*B 2.537,1.762 3.080,1.927 0.543,0.165 10 FOLD*B 0.243,0.424 0.815,0.590 0.571,0.165 10 RTRN*A 0.342,1.2 0.885,1.365 0.543,0.165 10 FOLD*A 1.575,1.749 1.696,1.907 0.121,0.157 10 E 2.038,1.083 2.432,1.083 false 1.025,1.284 1.419,1.284 false 1.588,1.012 1.082,0.505 1.082,0.505 0.961,0.505 false 1.861,1.341 2.368,1.847 2.368,1.847 2.488,1.847 false 1.636,1.358 1.636,1.721 false

Remove the No. 2 fold seat switch (See page Vehicle Interior>SEAT>POWER SEAT SWITCH(for Rear LH)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Switch Condition Specified Condition
8 (FOLD) - 7 (E) No. 2 fold seat switch LH fold Below 1 Ω
No. 2 fold seat switch LH off 10 kΩ or higher
3 (RTRN) - 7 (E) No. 2 fold seat switch LH return Below 1 Ω
No. 2 fold seat switch LH off 10 kΩ or higher

for RH Side
Tester Connection Switch Condition Specified Condition
6 (FOLD) - 7 (E) No. 2 fold seat switch RH fold Below 1 Ω
No. 2 fold seat switch RH off 10 kΩ or higher
1 (RTRN) - 7 (E) No. 2 fold seat switch RH return Below 1 Ω
No. 2 fold seat switch RH off 10 kΩ or higher


Text in Illustration
*A for LH Side
*B for RH Side



OK

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 FOLD SEAT SWITCH)

NG

REPLACE NO. 2 FOLD SEAT SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 FOLD SEAT SWITCH)
a.

Disconnect the d1*1 or c1*2 ECU connector.

*1: for LH Side

*2: for RH Side



b.

Disconnect the R12 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d1-15 (RTRN) - R12-3 (RTRN) Always Below 1 Ω
d1-15 (RTRN) - Body ground Always 10 kΩ or higher
d1-16 (FOLD) - R12-8 (FOLD) Always Below 1 Ω
d1-16 (FOLD) - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
c1-15 (RTRN) - R12-1 (RTRN) Always Below 1 Ω
c1-15 (RTRN) - Body ground Always 10 kΩ or higher
c1-16 (FOLD) - R12-6 (FOLD) Always Below 1 Ω
c1-16 (FOLD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR