Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Folding Motor Circuit  


DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switches and activates the power seat motors. At this time, the Hall IC detects the actuation of the seat cushion and sends a seat cushion actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

B246557E01
1.856,0.396 2.228,0.551 0.371,0.155 10 FLD+ 1.889,0.917 2.228,1.072 0.339,0.155 10 FLD- 1.947,1.589 2.229,1.744 0.282,0.155 10 SV1 1.849,2.217 2.228,2.372 0.378,0.155 10 SFLD 1.928,2.851 2.228,3.006 0.300,0.155 10 SG1 2.359,0.396 2.536,0.550 0.178,0.154 10 d2 2.358,0.917 2.535,1.071 0.178,0.154 10 d2 2.358,1.589 2.536,1.743 0.178,0.154 10 d1 2.358,2.217 2.535,2.371 0.178,0.154 10 d1 2.358,2.851 2.536,3.005 0.178,0.154 10 d1 2.699,0.396 2.866,0.550 0.167,0.154 10 c2 2.699,0.917 2.866,1.071 0.167,0.154 10 c2 2.699,1.589 2.866,1.743 0.167,0.154 10 c1 2.699,2.217 2.866,2.371 0.167,0.154 10 c1 2.699,2.851 2.866,3.005 0.167,0.154 10 c1 2.402,0.219 2.497,0.377 0.094,0.158 10 8 2.731,0.219 2.825,0.377 0.094,0.158 10 8 2.364,0.573 2.517,0.726 0.153,0.153 10 *1 2.702,0.573 2.855,0.726 0.153,0.153 10 *2 2.403,0.741 2.498,0.899 0.094,0.158 10 7 2.732,0.741 2.826,0.899 0.094,0.158 10 7 2.365,1.095 2.518,1.248 0.153,0.153 10 *1 2.703,1.095 2.856,1.248 0.153,0.153 10 *2 2.361,1.413 2.543,1.570 0.182,0.158 10 17 2.689,1.413 2.870,1.570 0.180,0.158 10 17 2.365,1.766 2.518,1.919 0.153,0.153 10 *1 2.703,1.766 2.856,1.919 0.153,0.153 10 *2 2.361,2.04 2.543,2.198 0.182,0.158 10 18 2.689,2.04 2.870,2.198 0.180,0.158 10 18 2.365,2.394 2.518,2.547 0.153,0.153 10 *1 2.703,2.394 2.856,2.547 0.153,0.153 10 *2 2.361,2.673 2.543,2.831 0.182,0.158 10 25 2.689,2.673 2.870,2.831 0.180,0.158 10 25 2.365,3.027 2.518,3.180 0.153,0.153 10 *1 2.703,3.027 2.856,3.180 0.153,0.153 10 *2 1.001,3.549 2.443,3.876 1.441,0.327 10 Fold Seat Control ECU LH*1, RH*2 4.521,0.288 4.615,0.446 0.094,0.158 10 3 4.522,0.81 4.616,0.968 0.094,0.158 10 4 4.522,1.482 4.619,1.640 0.097,0.158 10 5 4.522,2.109 4.619,2.267 0.097,0.158 10 2 4.522,2.743 4.619,2.900 0.097,0.158 10 6 5.589,2.144 6.027,2.298 0.438,0.154 10 Hall IC 4.536,3.542 4.813,3.696 0.276,0.154 10 d4 4.536,3.685 6.487,3.858 1.951,0.173 10 No. 3 Seat Leg Assembly LH*1 4.536,4.137 4.816,4.292 0.280,0.155 10 c4 4.536,4.288 6.266,4.461 1.729,0.173 10 No. 2 Seat Leg Assembly*2 0.12,4.155 1.049,4.310 0.929,0.154 10 *1: for LH Side 0.12,4.471 1.081,4.626 0.961,0.154 10 *2: for RH Side 3.709,0.116 3.862,0.269 0.153,0.153 10 *1 4.727,0.496 5.099,0.651 0.371,0.155 10 FWD 4.727,1.017 5.153,1.172 0.426,0.155 10 BACK 4.727,1.689 5.029,1.844 0.302,0.155 10 HLV 4.727,2.317 5.028,2.472 0.300,0.155 10 HLS 4.727,2.951 5.062,3.106 0.335,0.155 10 HLG

PROCEDURE

1.INSPECT SEAT LEG ASSEMBLY
a.
B239766E01
2.139,1.761 2.495,1.923 0.356,0.162 10 FWD 1.281,1.761 1.705,1.918 0.423,0.157 10 BACK 2.035,1.241 2.308,1.738 false 1.825,1.238 1.556,1.726 false

for LH Side:


ii.

Check if the No. 3 seat leg moves smoothly when the battery is connected to the cushion motor connector terminals.



b.

for RH Side:


ii.

Check if the No. 2 seat leg moves smoothly when the battery is connected to the cushion motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (FWD)
Battery negative (-) → 4 (BACK)
Forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 3 (FWD)
Backward


Result
Result Proceed to
OK (for LH Side) A
OK (for RH Side) B
NG (for LH Side) C
NG (for RH Side) D




A

2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEAT LEG)

B

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 SEAT LEG)

C

D

2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEAT LEG)
a.

Disconnect the d2 and d1 ECU connectors.


b.

Disconnect the d4 No. 3 seat leg connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-17 (SV1) - d4-5 (HLV) Always Below 1 Ω
d1-17 (SV1) - Body ground Always 10 kΩ or higher
d1-18 (SFLD) - d4-2 (HLS) Always Below 1 Ω
d1-18 (SFLD) - Body ground Always 10 kΩ or higher
d1-25 (SG1) - d4-6 (HLG) Always Below 1 Ω
d1-25 (SG1) - Body ground Always 10 kΩ or higher
d2-8 (FLD+) - d4-3 (FWD) Always Below 1 Ω
d2-8 (FLD+) - Body ground Always 10 kΩ or higher
d2-7 (FLD-) - d4-4 (BACK) Always Below 1 Ω
d2-7 (FLD-) - Body ground Always 10 kΩ or higher




OK

3.CHECK FOLD SEAT CONTROL ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOLD SEAT CONTROL ECU LH
a.

Remove the fold seat control ECU LH with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


b.
U115532E01
0.092,0.087 0.271,0.269 0.179,0.182 10 *a 1.302,0.965 1.482,1.119 0.180,0.154 10 d1 0.149,2.77 0.525,2.928 0.376,0.158 10 SFLD 2.445,0.965 2.620,1.119 0.175,0.154 10 d2 0.836,2.77 1.121,2.928 0.285,0.158 10 SV1 1.353,2.77 1.658,2.928 0.304,0.158 10 SG1 1.967,2.77 2.342,2.928 0.376,0.158 10 FLD+ 2.753,2.77 3.093,2.928 0.340,0.158 10 FLD- 0.773,1.693 0.36,2.6 0.36,2.6 0.36,2.732 false 0.849,1.693 1.013,2.6 1.013,2.6 1.013,2.732 false 1.759,1.794 1.527,2.606 1.527,2.606 1.527,2.738 false 2.485,1.794 2.164,2.606 2.164,2.606 2.164,2.738 false 2.602,1.794 2.922,2.606 2.922,2.606 2.922,2.738 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
d1-17 (SV1) - d1-25 (SG1) Ignition switch off Below 1 V
Ignition switch ON 5.5 to 8 V
d1-18 (SFLD) - d1-25 (SG1) Motor is operating Pulse generation
d2-8 (FLD+) - Body ground No. 1 or No. 2 fold seat switch LH fold 11 to 14 V
d2-7 (FLD-) - Body ground No. 1 or No. 2 fold seat switch LH return 11 to 14 V


Text in Illustration
*a Component with harness connected
(Fold Seat Control ECU LH)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 2 SEAT LEG)
a.

Disconnect the c2 and c1 ECU connectors.


b.

Disconnect the c4 No. 2 seat leg connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-17 (SV1) - c4-5 (HLV) Always Below 1 Ω
c1-17 (SV1) - Body ground Always 10 kΩ or higher
c1-18 (SFLD) - c4-2 (HLS) Always Below 1 Ω
c1-18 (SFLD) - Body ground Always 10 kΩ or higher
c1-25 (SG1) - c4-6 (HLG) Always Below 1 Ω
c1-25 (SG1) - Body ground Always 10 kΩ or higher
c2-8 (FLD+) - c4-3 (FWD) Always Below 1 Ω
c2-8 (FLD+) - Body ground Always 10 kΩ or higher
c2-7 (FLD-) - c4-4 (BACK) Always Below 1 Ω
c2-7 (FLD-) - Body ground Always 10 kΩ or higher




OK

5.CHECK FOLD SEAT CONTROL ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOLD SEAT CONTROL ECU RH
a.

Remove the fold seat control ECU RH with its connectors still connected (See page Vehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Rear No. 2 Seat)>REMOVAL).


b.
U115534E01
0.092,0.087 0.271,0.269 0.179,0.182 10 *a 1.331,0.965 1.497,1.119 0.166,0.154 10 c1 0.149,2.77 0.525,2.928 0.376,0.158 10 SFLD 2.4,0.965 2.564,1.119 0.164,0.154 10 c2 0.836,2.77 1.121,2.928 0.285,0.158 10 SV1 1.353,2.77 1.658,2.928 0.304,0.158 10 SG1 1.967,2.77 2.342,2.928 0.376,0.158 10 FLD+ 2.753,2.77 3.093,2.928 0.340,0.158 10 FLD- 0.773,1.693 0.36,2.6 0.36,2.6 0.36,2.732 false 0.849,1.693 1.013,2.6 1.013,2.6 1.013,2.732 false 1.759,1.794 1.527,2.606 1.527,2.606 1.527,2.738 false 2.485,1.794 2.164,2.606 2.164,2.606 2.164,2.738 false 2.602,1.794 2.922,2.606 2.922,2.606 2.922,2.738 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
c1-17 (SV1) - c1-25 (SG1) Ignition switch off Below 1 V
Ignition switch ON 5.5 to 8 V
c1-18 (SFLD) - c1-25 (SG1) Motor is operating Pulse generation
c2-8 (FLD+) - Body ground No. 1 or No. 2 fold seat switch RH fold 11 to 14 V
c2-7 (FLD-) - Body ground No. 1 or No. 2 fold seat switch RH return 11 to 14 V


Text in Illustration
*a Component with harness connected
(Fold Seat Control ECU RH)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG