Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Reclining Motor Circuit  


DESCRIPTION

The fold seat control ECU receives switch operation signals from the No. 1 and No. 2 fold seat switches and rear power seat switch and activates the power seat motors. At this time, the Hall IC detects the actuation of the seatback and sends a seatback actuation signal to the fold seat control ECU. The fold seat control ECU uses signals from the Hall IC to detect if an object is caught or if any other abnormal condition has occurred.

WIRING DIAGRAM

B239515E02
1.857,0.396 2.241,0.551 0.384,0.155 10 RCL+ 1.889,0.917 2.235,1.071 0.347,0.155 10 RCL- 1.947,1.589 2.229,1.744 0.282,0.155 10 SV2 1.85,2.217 2.245,2.371 0.395,0.155 10 SRCL 1.928,2.851 2.229,3.006 0.300,0.155 10 SG2 2.361,0.396 2.537,0.550 0.177,0.154 10 d2 2.36,0.917 2.537,1.070 0.177,0.154 10 d2 2.361,1.589 2.537,1.743 0.177,0.154 10 d1 2.36,2.217 2.537,2.370 0.177,0.154 10 d1 2.361,2.851 2.537,3.005 0.177,0.154 10 d1 2.695,0.396 2.864,0.550 0.169,0.154 10 c2 2.695,0.917 2.864,1.070 0.169,0.154 10 c2 2.695,1.589 2.864,1.743 0.169,0.154 10 c1 2.695,2.217 2.864,2.370 0.169,0.154 10 c1 2.695,2.851 2.864,3.005 0.169,0.154 10 c1 2.403,0.219 2.497,0.376 0.094,0.158 10 1 2.731,0.219 2.825,0.376 0.094,0.158 10 1 2.364,0.572 2.517,0.725 0.153,0.153 10 *1 2.703,0.572 2.856,0.725 0.153,0.153 10 *2 2.403,0.741 2.498,0.898 0.094,0.158 10 5 2.732,0.741 2.826,0.898 0.094,0.158 10 5 2.365,1.095 2.518,1.247 0.153,0.153 10 *1 2.703,1.095 2.856,1.247 0.153,0.153 10 *2 2.361,1.412 2.543,1.570 0.182,0.158 10 37 2.69,1.412 2.870,1.570 0.180,0.158 10 37 2.365,1.766 2.518,1.919 0.153,0.153 10 *1 2.703,1.766 2.856,1.919 0.153,0.153 10 *2 2.361,2.04 2.544,2.197 0.182,0.158 10 19 2.69,2.04 2.870,2.197 0.180,0.158 10 19 2.365,2.393 2.518,2.546 0.153,0.153 10 *1 2.703,2.393 2.856,2.546 0.153,0.153 10 *2 2.361,2.673 2.543,2.831 0.182,0.158 10 24 2.69,2.673 2.870,2.831 0.180,0.158 10 24 2.365,3.027 2.518,3.180 0.153,0.153 10 *1 2.703,3.027 2.856,3.180 0.153,0.153 10 *2 1.002,3.549 2.443,3.889 1.441,0.341 10 Fold Seat Control ECU LH*1, RH*2 4.521,0.288 4.615,0.446 0.094,0.158 10 3 4.522,0.81 4.616,0.968 0.094,0.158 10 4 4.522,1.482 4.619,1.639 0.097,0.158 10 5 4.522,2.109 4.619,2.267 0.097,0.158 10 2 4.522,2.742 4.619,2.900 0.097,0.158 10 6 5.589,2.143 6.027,2.298 0.438,0.154 10 Hall IC 4.229,3.541 4.533,3.695 0.304,0.154 10 d3 4.229,3.685 6.921,3.861 2.691,0.176 10 No. 3 Seatback Frame Sub-assembly LH*1 0.12,4.129 1.050,4.283 0.929,0.154 10 *1: for LH Side 0.12,4.445 1.081,4.599 0.961,0.154 10 *2: for RH Side 4.229,4.15 4.533,4.304 0.304,0.154 10 c3 4.229,4.294 6.950,4.470 2.720,0.176 10 No. 3 Seatback Frame Sub-assembly RH*2 4.715,0.496 5.100,0.651 0.384,0.155 10 FWD 4.715,1.017 5.143,1.171 0.428,0.155 10 BACK 4.715,1.689 5.025,1.844 0.309,0.155 10 HLV 4.715,2.317 5.111,2.472 0.395,0.155 10 HLS 4.715,2.951 5.043,3.106 0.327,0.155 10 HLG

PROCEDURE

1.INSPECT NO. 3 SEATBACK FRAME SUB-ASSEMBLY (RECLINING MOTOR)
a.
B239766E01
2.139,1.761 2.495,1.923 0.356,0.162 10 FWD 1.281,1.761 1.705,1.918 0.423,0.157 10 BACK 2.035,1.241 2.308,1.738 false 1.825,1.238 1.556,1.726 false

for LH Side:

i.

Remove the No. 3 seatback frame sub-assembly LH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


ii.

Check if the No. 3 seatback frame moves smoothly when the battery is connected to the reclining motor connector terminals.



b.

for RH Side:

i.

Remove the No. 3 seatback frame sub-assembly RH (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


ii.

Check if the No. 3 seatback frame moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 3 (FWD)
Battery negative (-) → 4 (BACK)
Forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 3 (FWD)
Backward


Result
Result Proceed to
OK (for LH Side) A
OK (for RH Side) B
NG (for LH Side) C
NG (for RH Side) D




A

2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME LH)

B

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME RH)

C

D

2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME LH)
a.

Disconnect the d2 and d1 ECU connectors.


b.

Disconnect the d3 No. 3 seatback frame connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d1-37 (SV2) - d3-5 (HLV) Always Below 1 Ω
d1-37 (SV2) - Body ground Always 10 kΩ or higher
d1-19 (SRCL) - d3-2 (HLS) Always Below 1 Ω
d1-19 (SRCL) - Body ground Always 10 kΩ or higher
d1-24 (SG2) - d3-6 (HLG) Always Below 1 Ω
d1-24 (SG2) - Body ground Always 10 kΩ or higher
d2-1 (RCL+) - d3-3 (FWD) Always Below 1 Ω
d2-1 (RCL+) - Body ground Always 10 kΩ or higher
d2-5 (RCL-) - d3-4 (BACK) Always Below 1 Ω
d2-5 (RCL-) - Body ground Always 10 kΩ or higher




OK

3.CHECK FOLD SEAT CONTROL ECU LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FOLD SEAT CONTROL ECU LH
a.

Remove the fold seat control ECU LH with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


b.

Measure the voltage according to the value(s) in the table below.


U115533E01
0.092,0.087 0.271,0.269 0.179,0.182 10 *a 1.292,0.965 1.467,1.119 0.174,0.154 10 d1 0.102,2.77 0.506,2.928 0.403,0.158 10 SRCL 2.415,0.965 2.590,1.119 0.174,0.154 10 d2 0.836,2.77 1.121,2.928 0.285,0.158 10 SV2 1.424,2.77 1.729,2.928 0.304,0.158 10 SG2 2.288,2.77 2.681,2.928 0.393,0.158 10 RCL- 2.889,2.77 3.271,2.928 0.383,0.158 10 RCL+ 0.705,1.693 0.36,2.6 0.36,2.6 0.36,2.732 false 0.849,1.789 1.013,2.6 1.013,2.6 1.013,2.732 false 1.83,1.794 1.598,2.606 1.598,2.606 1.598,2.738 false 2.806,1.794 2.486,2.606 2.486,2.606 2.486,2.738 false 2.846,1.689 3.095,2.606 3.095,2.606 3.095,2.738 false

Standard Voltage:
Tester Connection Condition Specified Condition
d1-37 (SV2) - d1-24 (SG2) Ignition switch off Below 1 V
Ignition switch ON 5.5 to 8 V
d1-19 (SRCL) - d1-24 (SG2) Motor is operating Pulse generation
d2-1 (RCL+) - Body ground Rear power seat switch LH forward 11 to 14 V
d2-5 (RCL-) - Body ground Rear power seat switch LH backward 11 to 14 V


Text in Illustration
*a Component with harness connected
(Fold Seat Control ECU LH)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

4.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - NO. 3 SEATBACK FRAME RH)
a.

Disconnect the c2 and c1 ECU connectors.


b.

Disconnect the c3 No. 3 seatback frame connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
c1-37 (SV2) - c3-5 (HLV) Always Below 1 Ω
c1-37 (SV2) - Body ground Always 10 kΩ or higher
c1-19 (SRCL) - c3-2 (HLS) Always Below 1 Ω
c1-19 (SRCL) - Body ground Always 10 kΩ or higher
c1-24 (SG2) - c3-6 (HLG) Always Below 1 Ω
c1-24 (SG2) - Body ground Always 10 kΩ or higher
c2-1 (RCL+) - c3-3 (FWD) Always Below 1 Ω
c2-1 (RCL+) - Body ground Always 10 kΩ or higher
c2-5 (RCL-) - c3-4 (BACK) Always Below 1 Ω
c2-5 (RCL-) - Body ground Always 10 kΩ or higher




OK

5.CHECK FOLD SEAT CONTROL ECU RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOLD SEAT CONTROL ECU RH
a.

Remove the fold seat control ECU RH with its connectors still connected (See page Vehicle Interior>SEAT>POWER SEAT CONTROL ECU (for Rear No. 2 Seat)>REMOVAL).


b.

Measure the voltage according to the value(s) in the table below.


U115535E01
0.092,0.087 0.271,0.269 0.179,0.182 10 *a 1.286,0.965 1.450,1.119 0.164,0.154 10 c1 0.102,2.77 0.506,2.928 0.403,0.158 10 SRCL 2.425,0.965 2.595,1.119 0.170,0.154 10 c2 0.836,2.77 1.121,2.928 0.285,0.158 10 SV2 1.424,2.77 1.729,2.928 0.304,0.158 10 SG2 2.288,2.77 2.681,2.928 0.393,0.158 10 RCL- 2.889,2.77 3.271,2.928 0.383,0.158 10 RCL+ 0.705,1.693 0.36,2.6 0.36,2.6 0.36,2.732 false 0.849,1.789 1.013,2.6 1.013,2.6 1.013,2.732 false 1.83,1.794 1.598,2.606 1.598,2.606 1.598,2.738 false 2.806,1.794 2.486,2.606 2.486,2.606 2.486,2.738 false 2.846,1.689 3.095,2.606 3.095,2.606 3.095,2.738 false

Standard Voltage:
Tester Connection Condition Specified Condition
c1-37 (SV2) - c1-24 (SG2) Ignition switch off Below 1 V
Ignition switch ON 5.5 to 8 V
c1-19 (SRCL) - c1-24 (SG2) Motor is operating Pulse generation
c2-1 (RCL+) - Body ground Rear power seat switch RH forward 11 to 14 V
c2-5 (RCL-) - Body ground Rear power seat switch RH backward 11 to 14 V


Text in Illustration
*a Component with harness connected
(Fold Seat Control ECU RH)


OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG