Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Rear Power Seat Switch Circuit  


DESCRIPTION

When the rear power seat switch is operated, a recline signal is sent to the fold seat control ECU. The ECU activates the power seat motor based on the signal from the rear power seat switch.

WIRING DIAGRAM

B239516E01
5.038,2.014 6.504,2.360 1.466,0.346 10 Fold Seat Control ECU LH*1, RH*2 5.282,0.625 5.729,0.829 0.447,0.204 10 RCLF 5.282,1.377 5.751,1.557 0.469,0.180 10 RCLR 2.622,0.739 2.969,0.901 0.346,0.162 10 FWD 2.56,1.483 2.968,1.632 0.408,0.149 10 BACK 1.688,1.107 1.804,1.264 0.116,0.158 10 E 4.953,1.377 5.126,1.533 0.174,0.156 10 d1 4.621,1.377 4.789,1.533 0.168,0.156 10 c1 4.624,1.55 4.775,1.709 0.151,0.159 10 *2 4.612,1.198 4.792,1.355 0.179,0.157 10 13 3.05,0.51 3.149,0.664 0.098,0.154 10 4 0.113,2.146 1.053,2.304 0.940,0.158 10 *1: for LH Side 0.113,2.456 1.073,2.612 0.960,0.155 10 *2: for RH Side 1.521,2.032 3.105,2.193 1.584,0.162 10 Rear Power Seat Switch 4.944,1.198 5.123,1.355 0.179,0.157 10 13 4.965,1.55 5.116,1.709 0.151,0.159 10 *1 4.953,0.625 5.127,0.781 0.174,0.156 10 d1 4.621,0.625 4.789,0.781 0.168,0.156 10 c1 4.624,0.797 4.775,0.957 0.151,0.159 10 *2 4.613,0.445 4.792,0.602 0.179,0.157 10 12 4.944,0.445 5.124,0.602 0.179,0.157 10 12 4.965,0.797 5.116,0.957 0.151,0.159 10 *1 3.05,1.257 3.149,1.412 0.098,0.154 10 5 1.512,0.882 1.610,1.036 0.098,0.154 10 6 1.521,1.871 2.399,2.039 0.878,0.168 10 R11*1, Q10*2

PROCEDURE

1.CHECK FOLD SEAT CONTROL ECU
a.
U115629E01
0.08,0.053 0.259,0.235 0.179,0.182 10 *a 1.595,0.522 1.763,0.676 0.168,0.154 10 c1 0.862,0.522 1.036,0.676 0.174,0.154 10 d1 1.557,1.799 1.975,1.956 0.418,0.157 10 RCLF 1.189,0.438 1.357,0.591 0.168,0.153 10 *A 1.903,0.438 2.071,0.591 0.168,0.153 10 *B 0.597,1.799 1.015,1.956 0.418,0.157 10 RCLR 1.224,1.258 1.801,1.61 1.801,1.61 1.801,1.755 false 1.152,1.258 0.856,1.61 0.856,1.61 0.856,1.755 false

Remove the fold seat control ECU with its connectors still connected (See page Vehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>DISASSEMBLY).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LH side
Tester Connection Condition Specified Condition
d1-12 (RCLF) - Body ground Always 11 to 14 V
Rear power seat switch LH forward Below 1 V
d1-13 (RCLR) - Body ground Always 11 to 14 V
Rear power seat switch LH backward Below 1 V

RH side
Tester Connection Condition Specified Condition
c1-12 (RCLF) - Body ground Always 11 to 14 V
Rear power seat switch RH forward Below 1 V
c1-13 (RCLR) - Body ground Always 11 to 14 V
Rear power seat switch RH backward Below 1 V


Text in Illustration
*A for LH Side
*B for RH Side
*a Component with harness connected
(Fold Seat Control ECU)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT REAR POWER SEAT SWITCH
2.INSPECT REAR POWER SEAT SWITCH
a.
B239690E01
1.407,1.706 1.829,1.860 0.421,0.154 10 BACK 2.127,1.706 2.477,1.860 0.349,0.154 10 FWD 1.037,1.706 1.161,1.860 0.123,0.154 10 E 1.646,1.193 1.646,1.68 false 1.486,1.191 1.111,1.535 1.111,1.535 1.111,1.68 false 1.821,1.191 2.303,1.535 2.303,1.535 2.303,1.68 false

Remove the rear power seat switch (See page Vehicle Interior>SEAT>POWER SEAT SWITCH(for Rear No. 2 Seat)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (FWD) - 6 (E) Always 10 kΩ or higher
Rear power seat switch forward Below 1 Ω
5 (BACK) - 6 (E) Always 10 kΩ or higher
Rear power seat switch backward Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH)

NG

3.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - REAR POWER SEAT SWITCH)

*1: for LH Side

*2: for RH Side


a.

Disconnect the d1*1 or c1*2 ECU connector.


b.

Disconnect the R11*1 or Q10*2 switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d1-12 (RCLF) - R11-4 (FWD) Always Below 1 Ω
d1-12 (RCLF) - Body ground Always 10 kΩ or higher
d1-13 (RCLR) - R11-5 (BACK) Always Below 1 Ω
d1-13 (RCLR) - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
c1-12 (RCLF) - Q10-4 (FWD) Always Below 1 Ω
c1-12 (RCLF) - Body ground Always 10 kΩ or higher
c1-13 (RCLR) - Q10-5 (BACK) Always Below 1 Ω
c1-13 (RCLR) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR