Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053738 SEAT BELT _0261164 FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door) A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY(for 3 Door)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B239046

Align the claw with the anchor plate positioning hole and install the shoulder anchor adjuster with the 2 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)

HINT:

First install the lower bolt, and then install the upper bolt.



Hide 73220 2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

U115599E06
1.531,1.458 2.604,0.76 2.604,0.76 1.833,1.49 true 2.646,0.635 2.854,0.833 0.208,0.198 10 false a

NOTICE:

When installing the retractor, make sure the claws of the vehicle (labeled "a" in the illustration) only contact the installation areas of the retractor.


a.

Align the seat belt retractor positioning holes with the claws of the vehicle.


b.

Install the seat belt with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


c.
B242876E03
2.323,0.198 2.583,0.458 0.26,0.26 10 false A 0.49,1.125 0.656,1.313 0.167,0.188 10 true B

Connect the pretensioner connector labeled A as shown in the illustration.


d.

w/ Pre-Crash Safety System:

Connect the pre-crash safety connector labeled B.


e.

Install the shoulder anchor to the shoulder belt anchor adjuster with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62520P 3.INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH

Hide 64740C 4.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Connect the connector.


b.

Attach the 9 claws and 11 clips to install the deck trim side panel.


c.

Install the 3 bolts and 2 screws.


d.

Install the rear No. 1 seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


e.

Install the front seat outer belt floor anchor with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 64712F 5.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)

Hide 64937A 6.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/ o Tonneau Cover)

Hide 64725D 7.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK

Hide 58574A 10.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

Hide 64910M 12.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)

Hide 62312B 13.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).