Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


U149186E04
5.865,0.188 6.073,0.385 0.208,0.198 10 false z1 3.99,0.198 4.365,0.396 0.375,0.198 10 false G25 1.656,0.188 2.031,0.385 0.375,0.198 10 false G24

a.

Disconnect the G24 and G25 amplifier connectors.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G25-21 (B) - G25-14 (GND) V - W-B Battery power source Always 11 to 14 V
G25-1 (IG+) - G25-14 (GND) L - W-B Ignition power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G25-14 (GND) - Body ground W-B - Body ground Ground for main power supply Always Below 1 Ω
G24-20 (RGND) - Body ground W-B - Body ground Ground for main power supply Always Below 1 Ω
G24-24 (+B2) - G24-20 (RGND) GR - W-B Battery power source Always 11 to 14 V


c.

Reconnect the G24 and G25 amplifier connectors.


d.

Measure the voltage and waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G25-3 (PTC1) - Body ground*2 V - Body ground PTC NO.1 relay operation signal*10
PTC HTR NO.1 relay operation signal*11
·

Engine running (1250 rpm or more)

·

Temperature setting MAX HOT

·

Outside temperature 10°C (50°F) or less

·

Engine coolant temperature 79°C (175°F) or less

·

Headlight dimmer switch off

·

Blower switch off → on


11 to 14 V → Below 1 V
G25-4 (PTC3) - Body ground*2 P - Body ground PTC NO.3 relay operation signal*10
PTC HTR NO.3 relay operation signal*11
·

Engine running (1250 rpm or more)

·

Temperature setting MAX HOT

·

Outside temperature 10°C (50°F) or less

·

Engine coolant temperature 73°C (163°F) or less

·

Headlight dimmer switch off

·

Blower switch off → on


11 to 14 V → Below 1 V
G25-5 (TAM) - G25-13 (SG-2) V - G Cooler thermistor (ambient temperature sensor) signal
·

Ignition switch ON

·

Ambient temperature 25°C (77°F)


1.35 to 1.75 V
G25-5 (TAM) - G25-13 (SG-2) V - G Cooler thermistor (ambient temperature sensor) signal
·

Ignition switch ON

·

Ambient temperature 40°C (104°F)


0.9 to 1.2 V
G25-8 (LOCK) - G25-13 (SG-2) R - G A/C compressor lock sensor signal
·

Engine running

·

Blower switch LO

·

A/C switch on (magnet clutch on)


Pulse generation
(See waveform 1)
G25-9 (PRE) - G25-13 (SG-2)*3 G - G Air conditioner pressure sensor signal
·

Ignition switch ON

·

Refrigerant pressure normal (below 3.025 MPa [30.9 kgf/cm2, 438.6 psi] and higher than 0.176 MPa [1.8 kgf/cm2, 25.5 psi])


0.63 to 4.72 V
G25-9 (PRE) - G25-13 (SG-2)*3 G - G Air conditioner pressure sensor signal
·

Ignition switch ON

·

Refrigerant pressure abnormal (below 0.176 MPa [1.8 kgf/cm2, 25.5 psi])


Below 0.63 V
G25-9 (PRE) - G25-13 (SG-2)*3 G - G Air conditioner pressure sensor signal
·

Ignition switch ON

·

Refrigerant pressure abnormal (higher than 3.025 MPa [30.9 kgf/cm2, 438.6 psi])


4.72 V or higher
G25-9 (PRE) - Body ground*4 G - Body ground No. 1 pressure switch signal
·

Ignition switch ON

·

Refrigerant pressure normal (below 3.14 MPa [32.0 kgf/cm2, 455 psi] and higher than 0.196 MPa [2.0 kgf/cm2, 28 psi])


Below 1 V
G25-9 (PRE) - Body ground*4 G - Body ground No. 1 pressure switch signal
·

Ignition switch ON

·

Refrigerant pressure abnormal (below 0.196 MPa [2.0 kgf/cm2, 28 psi] or higher than 3.14 MPa [32.0 kgf/cm2, 455 psi])


4.69 V or higher
G25-10 (S5-3) - G25-13 (SG-2) B - G Power supply for air conditioner pressure sensor Ignition switch ON 4.75 to 5.25 V
G25-15 (COOL) - G25-14 (GND)*5 V - W-B Cooling box assembly operation signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
G25-16 (MG+) - G25-14 (GND)*6 V - W-B Viscous with magnetic clutch heater assembly operation signal
·

Engine running

·

Power heater switch on


Below 1 V
G25-17 (AC1) - G25-14 (GND) LG - W-B Compressor operation signal
·

Engine running

·

Blower switch LO

·

A/C switch off


11 to 14 V
·

Engine running

·

Blower switch LO

·

A/C switch on


Below 1 V
G25-18 (HTR1) - G25-14 (GND)*12 G - W-B Engine operating signal Engine idling 11 to 14 V
G25-20 (MGC) - G25-14 (GND) R - W-B Magnet clutch assembly operation signal
·

Engine running

·

A/C switch off → on

·

Blower switch LO

·

Magnet clutch assembly off → on


11 to 14 V → Below 1 V
G25-22 (PTC2) - Body ground*2 LG - Body ground PTC NO.2 relay operation signal*10
PTC HTR NO.2 relay operation signal*11
·

Engine running (1250 rpm or more)

·

Temperature setting MAX HOT

·

Outside temperature 10°C (50°F) or less

·

Engine coolant temperature 76°C (169°F) or less

·

Headlight dimmer switch off

·

Blower switch off → on


11 to 14 V → Below 1 V
G25-23 (BLW) - G25-14 (GND) L - W-B Blower with fan motor sub-assembly control signal
·

Ignition switch ON

·

Blower switch LO


Pulse generation
(See waveform 2)
G25-25 (ALT) - G25-14 (GND)*13 L - W-B Generator signal (PTC heater control) Engine started Pulse generation
G25-27 (ACT) - G25-14 (GND) R - W-B Compressor operation signal
·

Engine running

·

Blower switch LO

·

A/C switch off (magnet clutch off)


Below 1 V
·

Engine running

·

Blower switch LO

·

A/C switch on (magnet clutch on)


4.75 to 5.25 V
G25-29 (TR) - G25-34 (SG-1) GR - P Cooler thermistor (room temperature sensor) signal
·

Ignition switch ON

·

Cabin temperature at 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature at 40°C (104°F)


1.2 to 1.6 V
G25-32 (TSP) - G25-14 (GND) V - W-B*8
G - W-B*9
Automatic light control sensor (solar sensor) power signal (for front passenger side)
·

Ignition switch ON

·

Solar sensor subjected to electric light

·

Vehicle indoors


0.8 to 4.3 V
·

Ignition switch ON

·

Automatic light control sensor (solar sensor) covered with cloth

·

Vehicle indoors


Below 0.8 V
G25-33 (TSD) - G25-14 (GND) G - W-B*8
V - W-B*9
Automatic light control sensor (solar sensor) power signal (for driver side)
·

Ignition switch ON

·

Solar sensor subjected to electric light

·

Vehicle indoors


0.8 to 4.3 V
·

Ignition switch ON

·

Automatic light control sensor (solar sensor) covered with cloth

·

Vehicle indoors


Below 0.8 V
G25-36 (SWVC) - G25-14 (GND)*6, *7 W - W-B
·

Heater switch assembly operation signal*6

·

Idle up switch operation signal*7


·

Engine running

·

A/C switch on

·

Heater switch assembly on*5

·

Idle up switch on*6


Below 1 V
G25-37 (LIN1) - Body ground P - Body ground LIN communication signal Ignition switch ON Pulse generation
G24-1 (RBUS) - G24-21 (RBUG)*1 LG - L BUS IC control signal (for Rear) Ignition switch ON Pulse generation
G24-4 (TEC) - G24-19 (SGND)*1 SB - V Rear evaporator temperature sensor signal
·

Ignition switch ON

·

Rear evaporator temperature 0°C (32°F)


2.0 to 2.4 V
·

Ignition switch ON

·

Rear evaporator temperature 15°C (59°F)


1.4 to 1.8 V
G24-7 (SG-6) - Body ground*1 R - Body ground Ground for cooler thermistor (rear room temperature sensor) Always Below 1 V
G24-12 (SWCB) - G25-14 (GND)*5 LG - W-B Cooling box assembly operation signal
·

Engine running

·

A/C switch on

·

Cooler control switch sub-assembly on


Below 1 V
G24-13 (RLIN) - Body ground*1 L - Body ground LIN communication signal Ignition switch ON Pulse generation
G24-17 (TR) - G24-7 (SG-6)*1 B - R Cooler thermistor (rear room temperature sensor) signal
·

Ignition switch ON

·

Cabin temperature 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature 40°C (104°F)


1.2 to 1.6 V
G24-19 (SGND) - Body ground*1 V - Body ground Ground for rear evaporator temperature sensor Always Below 1 V
G24-22 (BLWH) - G24-20 (RGND)*1 W - W-B Rear blower with fan motor sub-assembly control signal
·

Ignition switch ON

·

Rear blower switch on


Pulse generation
(See waveform 3)
G24-23 (RBBU) - G24-21 (RBUG)*1 P - L Power supply for BUS IC (for Rear) Always 11 to 14 V
z1-2 (BUS G) - Body ground - Ground for BUS IC Always Below 1 V
z1-3 (BUS) - z1-2 (BUS G) - BUS IC control signal Ignition switch ON Pulse generation
z1-4 (B BUS) - z1-2 (BUS G) - Power supply for BUS IC Always 11 to 14 V
z1-6 (TEA) - z1-5 (SGA) - No. 1 cooler thermistor signal
·

Ignition switch ON

·

Evaporator temperature 0°C (32°F)


1.7 to 2.1 V
·

Ignition switch ON

·

Evaporator temperature 15°C (59°F)


0.9 to 1.3 V

*1: w/ Rear Air Conditioning System

*2: w/ PTC Heater

*3: for Sensor Type

*4: for Switch Type

*5: w/ Refrigerated Cool Box

*6: w/ Viscous Heater

*7: w/ Idle Up Switch

*8: for LHD

*9: for RHD

*10: w/o Urea SCR System

*11: w/ Urea SCR System

*12: w/ Combustion Type Power Heater System

*13: w/ PTC Heater (for 1GR-FE or 1KD-FTV)



e.
E116941E16
0.208,0.969 0.573,1.167 0.365,0.198 10 false GND

Using an oscilloscope, check waveform 1.

A/C Compressor Lock Sensor Signal
Item Content
Terminal No. (Symbol) G25-8 (LOCK) - G25-13 (SG-2)
Tool Setting 200 mV/DIV., 10 ms./DIV.
Condition
·

Engine running

·

Blower switch LO

·

A/C switch on (magnet clutch on)




f.
E103396E56
2.927,1.656 3.302,1.833 0.375,0.177 10 false GND

Using an oscilloscope, check waveform 2.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) G25-23 (BLW) - G25-14 (GND)
Tool Setting 1 V/DIV., 500 μs/DIV.
Condition
·

Ignition switch ON

·

Blower switch LO



HINT:

When the blower level is increased, the duty ratio changes accordingly.



g.
E326700E02
2.792,1.448 3.271,1.656 0.479,0.208 10 false GND

Using an oscilloscope, check waveform 3.

Blower Motor Control Signal
Item Content
Terminal No. (Symbol) G24-22 (BLWH) - G24-20 (RGND)
Tool Setting 2 V/DIV., 500 μs/DIV.
Condition
·

Ignition switch ON

·

Blower switch LO



HINT:

When the blower level is increased, the duty ratio changes accordingly.




CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (FOR COOLING BOX) (w/ Refrigerated Cool Box)


E197829

a.

Disconnect the air conditioning amplifier (for cooling box) connector.


b.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
1 (+B) - 4 (GND) W-R - W-B Battery power source Always 11 to 14 V
2 (IG+) - 4 (GND) GR - W-B IG power supply Ignition switch ON 11 to 14 V


c.

Reconnect the air conditioning amplifier (for cooling box) connector.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
5 (SW) - 4 (GND) LG-R - W-B Cooler control switch sub-assembly operation signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
6 (CBI) - 4 (GND) L-G - W-B Cooler compressor permission signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
7 (LED) - 4 (GND) L-B - W-B Cooling box indicator signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
8 (CBT) - 4 (GND) BR-Y - W-B Air conditioning amplifier assembly request signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
9 (BLW) - 4 (GND) W - W-B No. 1 cooler blower motor sub-assembly operation signal
·

Engine running

·

Cooler control switch sub-assembly on


Below 1 V
10 (SG) - 4 (GND) W-L - W-B Ground Always Below 1 Ω



CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY


U149297E03
3.438,0.26 3.792,0.438 0.354,0.177 10 false G23

a.

Disconnect the G23 panel connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G23-1 (+B) - G23-4 (GND) L - W-B Battery power source Always 11 to 14 V
G23-5 (IG) - G23-4 (GND) L - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G23-6 (ACC) - G23-4 (GND) P - W-B ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
G23-4 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G23 panel connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
G23-3 (LIN1) - Body ground P - Body ground LIN communication signal Ignition switch ON Pulse generation



CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Air Conditioning System, w/o Rear Seat Heater)


U149298E03
3.49,0.271 3.76,0.448 0.271,0.177 10 false T3

a.

Disconnect the T3 control connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T3-5 (IG) - T3-8 (E) L - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
T3-8 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the T3 control connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
T3-3 (RLIN) - Body ground L - Body ground LIN communication signal Ignition switch ON Pulse generation



CHECK AIR CONDITIONING CONTROL ASSEMBLY (w/ Rear Air Conditioning System, w/ Rear Seat Heater)


U170567E02
3.542,0.271 3.833,0.427 0.292,0.156 10 false T7

a.

Disconnect the T7 control connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
T7-1 (IG) - T7-8 (E) L - W-B IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
T7-8 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the T7 control connector.


d.

Measure the waveform according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Switch Condition Specified Condition
T7-6 (RLIN) - Body ground L - Body ground LIN communication signal Ignition switch ON Pulse generation



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169677E01
0.028,1.291 0.716,1.447 0.688,0.156 10 2I*1, 2H*2 1.086,3.877 1.367,4.033 0.280,0.156 10 G63 0.901,2.214 1.109,2.370 0.208,0.156 10 2F 5.866,1.535 6.074,1.691 0.208,0.156 10 2D 5.866,2.238 6.074,2.394 0.208,0.156 10 2A 1.076,2.754 1.284,2.910 0.208,0.156 10 2K 3.75,1.339 3.869,1.481 0.119,0.142 10 A 1.961,1.203 2.272,1.345 0.311,0.142 10 G65 1.623,1.511 1.866,1.268 1.866,1.268 1.944,1.268 false 1.961,1.561 2.263,1.703 0.302,0.142 10 G64 1.623,1.868 1.866,1.626 1.866,1.626 1.944,1.626 false 1.961,1.878 2.305,2.020 0.343,0.142 10 G63 1.623,2.186 1.866,1.944 1.866,1.944 1.944,1.944 false 3.588,3.877 3.868,4.033 0.280,0.156 10 G64 1.42,5.184 1.635,5.339 0.214,0.156 10 2H 0.848,5.184 1.021,5.339 0.173,0.156 10 2I 1.881,6.415 2.095,6.571 0.214,0.156 10 2D 4.939,6.415 5.153,6.571 0.214,0.156 10 2A 3.509,7.686 3.640,7.842 0.131,0.156 10 A 3.95,5.188 4.150,5.343 0.200,0.156 10 2F 5.896,5.188 6.096,5.343 0.200,0.156 10 2K 5.892,3.877 6.172,4.033 0.280,0.156 10 G65 0.719,1.363 0.814,1.363 0.814,1.363 0.982,1.531 false 1.716,5.114 1.889,5.270 0.173,0.156 10 *2 1.081,5.114 1.253,5.270 0.173,0.156 10 *1 0.25,8.497 0.989,8.652 0.739,0.156 10 *2: for RHD 0.25,8.262 0.989,8.418 0.739,0.156 10 *1: for LHD

a.

b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G64-20 (CLTB) - Body ground P - Body ground Automatic light control sensor power supply output Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G64-22 (CLTE) - Body ground L - Body ground Automatic light control sensor ground Always Below 1 Ω