Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1449/49  Rear Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The rear mode damper servo sub-assembly sends pulse signals to indicate the damper position to the air conditioning amplifier assembly. The air conditioning amplifier assembly activates the motor (normal or reverse) based on these signals to move the rear air outlet damper to any position, which controls the air outlet modes.

The air conditioning amplifier assembly communicates with the servo through the No. 2 air conditioning harness.

HINT:

Confirm that there are no mechanical problems because this DTC may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1449/49 Rear air outlet damper position does not change when the air conditioning amplifier assembly operates the rear mode damper servo sub-assembly.
·

Rear mode damper servo sub-assembly

·

No. 2 air conditioning harness assembly

·

Harness or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E193116E07
5.527,2.122 7.119,2.504 1.592,0.382 10 Air Conditioning Amplifier Assembly 2.367,2.314 5.066,2.482 2.698,0.168 10 No. 2 Air Conditioning Harness Assembly 0.601,2.02 2.317,2.389 1.716,0.369 10 Rear Mode Damper Servo Sub-assembly 5.578,0.479 5.981,0.660 0.403,0.181 10 RBUS 3.401,0.468 3.804,0.649 0.403,0.181 10 RBUS 5.32,0.377 5.476,0.559 0.156,0.181 10 1 3.932,0.386 4.088,0.568 0.156,0.181 10 3 5.586,1.033 5.989,1.215 0.403,0.181 10 RBBU 3.401,1.034 3.804,1.215 0.403,0.181 10 RBBU 5.289,0.948 5.461,1.129 0.171,0.181 10 23 3.932,0.933 4.088,1.114 0.156,0.181 10 4 5.574,1.592 5.993,1.774 0.418,0.181 10 RBUG 3.401,1.573 3.820,1.755 0.418,0.181 10 RBUG 5.317,1.487 5.489,1.668 0.171,0.181 10 21 3.932,1.464 4.088,1.645 0.156,0.181 10 2 2.361,2.151 2.700,2.321 0.339,0.170 10 Q13 5.521,1.967 5.837,2.123 0.316,0.156 10 G24 3.101,1.036 3.306,1.206 0.205,0.170 10 IC

PROCEDURE

1.CHECK FOR DTC


Result
Result Proceed to
DTC B1449/49 is not output A
DTC B1449/49 is output B
DTC B1449/49 and B1497/97 are output C


A

B

2.READ VALUE USING INTELLIGENT TESTER (REAR MODE DAMPER SERVO)

C

2.READ VALUE USING INTELLIGENT TESTER (REAR MODE DAMPER SERVO)
a.

Use the Data List to check if the rear mode damper servo sub-assembly is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (R) Rear mode damper servo sub-assembly target pulse / Min.: 0, Max.: 255 82 (pulse): FACE
41 (pulse): B/L
7 (pulse): FOOT
-
Air Mix Servo Actual Pulse (R) Rear mode damper servo sub-assembly actual pulse / Min.: 0, Max.: 255 82 (pulse): FACE
41 (pulse): B/L
7 (pulse): FOOT
-

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
Both target pulse and actual pulse do not display C
Target pulse displays normally, but actual pulse does not display D


A

3.CHECK FOR DTC

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

D

4.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
4.CHECK HARNESS AND CONNECTOR (NO. 2 AIR CONDITIONING HARNESS - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the Q13 harness connector.


b.

Disconnect the G24 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q13-3 (RBUS) - G24-1 (RBUS) Always Below 1 Ω
Q13-4 (RBBU) - G24-23 (RBBU) Always Below 1 Ω
Q13-2 (RBUG) - G24-21 (RBUG) Always Below 1 Ω
G24-1 (RBUS) - Body ground Always 10 kΩ or higher
G24-23 (RBBU) - Body ground Always 10 kΩ or higher
G24-21 (RBUG) - Body ground Always 10 kΩ or higher




OK

5.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK REAR MODE DAMPER SERVO SUB-ASSEMBLY
a.

Replace the rear mode damper servo sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>REAR AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the rear mode damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the rear mode damper servo sub-assembly with a new or normally functioning one.






OK

END (REAR MODE DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

NG

6.CHECK AIR CONDITIONING HARNESS ASSEMBLY
6.CHECK AIR CONDITIONING HARNESS ASSEMBLY

OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY