Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  Idle Up Switch Circuit  


DESCRIPTION

When the idle up switch is pushed, the air conditioning amplifier assembly outputs the engine idle up signal. If engine idle up does not occur when the idle up switch is pushed, there may be a problem in the circuit shown below.

WIRING DIAGRAM

E196912E02
5.225,2.004 6.842,2.396 1.617,0.392 10 Air Conditioning Amplifier Assembly 5.219,1.841 5.555,2.034 0.337,0.193 10 G25 1.059,1.459 2.071,1.665 1.012,0.206 10 Idle Up Switch 1.06,1.301 1.383,1.493 0.323,0.193 10 G20 5.328,0.372 5.554,0.565 0.225,0.193 10 36 5.608,0.468 6.093,0.661 0.485,0.193 10 SWVC 2.412,0.775 2.575,0.968 0.163,0.193 10 3 2.412,0.378 2.575,0.571 0.163,0.193 10 6 2.055,0.371 2.350,0.564 0.295,0.193 10 SW 2.177,0.785 2.361,0.978 0.184,0.193 10 E

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (IDLE UP SWITCH)
a.

Use the Data List to check if the idle up switch is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IDLE UP/PWR HEAT Switch Idle up switch / ON or OFF ON: Idle up switch on
OFF: Idle up switch off
-

OK:

The display is as specified in the normal condition column.




OK

NG

2.INSPECT IDLE UP SWITCH
2.INSPECT IDLE UP SWITCH
a.
E196913E01
2.174,1.738 2.320,1.923 0.146,0.185 10 E 1.138,1.751 1.432,1.935 0.294,0.185 10 SW 1.345,1.713 1.459,1.261 false 2.024,1.261 2.187,1.713 false

Remove the idle up switch (See page Vehicle Interior>HEATING / AIR CONDITIONING>HEATER SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (SW) - 3 (E) Idle up switch on Below 1 Ω
6 (SW) - 3 (E) Idle up switch off 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (IDLE UP SWITCH - AIR CONDITIONING AMPLIFIER AND BODY GROUND)
a.

Disconnect the G20 switch connector.


b.

Disconnect the G25 amplifier connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G20-6 (SW) - G25-36 (SWVC) Always Below 1 Ω
G20-3 (E) - Body ground Always Below 1 Ω
G25-36 (SWVC) - Body ground Always 10 kΩ or higher




OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR