The damper servo sub-assembly (air mix damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air mix damper to any position. As a result, the air mix damper varies the mixture of hot air from the heater core and cold air from the evaporator so that the temperature of the air is as requested.
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1441 | The air mix damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (air mix damper servo). | ·
Damper servo sub-assembly (air mix damper servo) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
| Result | Proceed to |
|---|---|
| DTC B1441 is not output | A |
| DTC B1441 is output | B |
| DTC B1441 and B1497 are output | C |
A
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
B
C
Use the Data List to check if the damper servo sub-assembly (air mix damper servo) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Air Mix Servo Targ Pulse (D) | Damper servo sub-assembly (air mix damper servo) target pulse / Min.: 0, Max.: 255 | 112 or 127 (pulse): MAX COOL
21 or 31 (pulse): MAX HOT |
- |
| Air Mix Servo Actual Pulse (D) | Damper servo sub-assembly (air mix damper servo) actual pulse / Min.: 0, Max.: 255 | 112 or 127 (pulse): MAX COOL
21 or 31 (pulse): MAX HOT |
- |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| OK (When troubleshooting according to the DTC) | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| Both target pulse and actual pulse do not display | C |
| Target pulse displays normally, but actual pulse does not display | D |
A
B
C
D
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441 is not output.
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Replace the damper servo sub-assembly (air mix damper servo) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).
Since the damper servo sub-assembly (air mix damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (air mix damper servo) with a new or normally functioning one.
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441 is not output.
OK
NG
Temporarily replace the air conditioning harness assembly with a new or normally functioning one (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DTC CHECK / CLEAR).
DTC B1441 is not output.
OK
NG