Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1442  Air Inlet Damper Control Servo Motor Circuit  


DESCRIPTION

The recirculation damper servo sub-assembly sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air inlet damper to any position, which controls the intake air settings (fresh, fresh/recirculation and recirculation).

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1442 The air inlet damper position does not change when the air conditioning amplifier assembly operates the recirculation damper servo sub-assembly.
·

Recirculation damper servo sub-assembly

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E180810E98
5.333,0.427 5.469,0.583 0.135,0.156 10 false 4 5.323,0.979 5.448,1.135 0.125,0.156 10 false 3 5.323,1.5 5.448,1.656 0.125,0.156 10 false 2 3.177,1.063 3.375,1.208 0.198,0.146 10 false IC 0.531,2.052 2.302,2.385 1.771,0.333 10 false Recirculation Damper Servo Sub-assembly 5.51,2.146 7.073,2.615 1.563,0.469 10 false Air Conditioning Amplifier Assembly 5.531,2.01 5.76,2.167 0.229,0.156 10 false z1 2.865,2.167 5.115,2.313 2.25,0.146 10 false Air Conditioning Harness Assembly 5.573,0.5 6.115,0.656 0.542,0.156 10 false B BUS 5.583,1.063 5.979,1.219 0.396,0.156 10 false BUS 5.583,1.615 6.063,1.771 0.479,0.156 10 false BUS G

PROCEDURE

1.CHECK FOR DTC


Result
Result Proceed to
DTC B1442 is not output A
DTC B1442 is output B
DTC B1442 and B1497 are output C


A

B

2.READ VALUE USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)

C

2.READ VALUE USING INTELLIGENT TESTER (RECIRCULATION DAMPER SERVO)
a.

Use the Data List to check if the recirculation damper servo sub-assembly is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Inlet Damper Targ Pulse Recirculation damper servo sub-assembly target pulse / Min.: 0, Max.: 255 7 (pulse): Recirculation
26 (pulse): Fresh
-
Air Inlet Damper Actual Pulse Recirculation damper servo sub-assembly actual pulse / Min.: 0, Max.: 255 7 (pulse): Recirculation
26 (pulse): Fresh
-

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
Both target pulse and actual pulse do not display C
Target pulse displays normally, but actual pulse does not display D


A

3.CHECK FOR DTC

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

D

4.CHECK RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
4.CHECK RECIRCULATION DAMPER SERVO SUB-ASSEMBLY
a.

Replace the recirculation damper servo sub-assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>BLOWER UNIT>DISASSEMBLY).

HINT:

Since the recirculation damper servo sub-assembly cannot be inspected while it is removed from the vehicle, replace the recirculation damper servo sub-assembly with a new or normally functioning one.






OK

END (RECIRCULATION DAMPER SERVO SUB-ASSEMBLY IS FAULTY)

NG

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
5.CHECK AIR CONDITIONING HARNESS ASSEMBLY

OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY