Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1443  Air Outlet Damper Control Servo Motor Circuit  


DESCRIPTION

The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:

Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code DTC Detection Condition Trouble Area
B1443 The air outlet damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo).
·

Damper servo sub-assembly (mode damper servo)

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E180810E99
5.333,0.406 5.469,0.563 0.135,0.156 10 false 4 5.323,0.958 5.448,1.115 0.125,0.156 10 false 3 5.323,1.49 5.448,1.646 0.125,0.156 10 false 2 3.177,1.063 3.375,1.208 0.198,0.146 10 false IC 0.583,2.021 2.427,2.417 1.844,0.396 10 false Damper Servo Sub-assembly (Mode Damper Servo) 5.438,2.198 7.021,2.604 1.583,0.406 10 false Air Conditioning Amplifier Assembly 5.438,2.052 5.625,2.208 0.188,0.156 10 false z1 2.865,2.125 5.115,2.271 2.25,0.146 10 false Air Conditioning Harness Assembly 5.583,0.51 6.125,0.667 0.542,0.156 10 false B BUS 5.583,1.073 5.979,1.229 0.396,0.156 10 false BUS 5.583,1.594 6.063,1.75 0.479,0.156 10 false BUS G

PROCEDURE

1.CHECK FOR DTC


Result
Result Proceed to
DTC B1443 is not output A
DTC B1443 is output B
DTC B1443 and B1497 are output C


A

B

2.READ VALUE USING INTELLIGENT TESTER (MODE DAMPER SERVO)

C

2.READ VALUE USING INTELLIGENT TESTER (MODE DAMPER SERVO)
a.

Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Air Outlet Servo Pulse (D) Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 15 (pulse): FACE
41 (pulse): B/L
65 or 73 (pulse): FOOT
83 or 95 (pulse): F/D
113 (pulse): DEF
-
Air Outlet Servo Actu Pulse (D) Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255 15 (pulse): FACE
41 (pulse): B/L
65 or 73 (pulse): FOOT
83 or 95 (pulse): F/D
113 (pulse): DEF
-

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to the DTC) A
OK (When troubleshooting according to Problem Symptoms Table) B
Both target pulse and actual pulse do not display C
Target pulse displays normally, but actual pulse does not display D


A

3.CHECK FOR DTC

B

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

D

4.CHECK DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
4.CHECK DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
a.

Replace the damper servo sub-assembly (mode damper servo) (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).

HINT:

Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.






OK

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY)

NG

5.CHECK AIR CONDITIONING HARNESS ASSEMBLY
5.CHECK AIR CONDITIONING HARNESS ASSEMBLY

OK

END (AIR CONDITIONING HARNESS ASSEMBLY IS FAULTY)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY