Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261170 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1422  Compressor Lock Sensor Circuit  


SYSTEM DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the cooler compressor assembly is locked and turns the magnet clutch assembly off.

DTC Code DTC Detection Condition Trouble Area
B1422 Open or short in the compressor lock sensor circuit.
·

Cooler compressor assembly (A/C lock sensor)

·

Compressor drive belt

·

Harness or connector

·

Air conditioning amplifier assembly

·

CAN communication system



WIRING DIAGRAM

E193114E11
1.735,0.564 2.099,0.757 0.364,0.193 10 ECM 5.4,1.753 5.847,1.913 0.447,0.160 10 LOCK 5.407,2.765 5.806,2.932 0.399,0.167 10 SG-2 3.074,1.636 3.248,1.810 0.174,0.174 10 1 1.741,1.64 1.915,1.815 0.174,0.174 10 2 1.689,2.264 4.794,2.461 3.105,0.197 10 Cooler Compressor Assembly (A/C Lock Sensor) 4.9,3.39 7.144,3.594 2.244,0.204 10 Air Conditioning Amplifier Assembly 5.159,1.603 5.313,1.745 0.154,0.142 10 8 5.094,2.638 5.285,2.811 0.191,0.173 10 13 1.69,2.094 1.991,2.243 0.302,0.149 10 C39 4.92,3.245 5.228,3.401 0.309,0.156 10 G25 2.629,1.65 3.025,1.806 0.397,0.156 10 SSR+ 1.94,1.65 2.337,1.806 0.397,0.156 10 SSR- 0.838,3.435 2.517,3.628 1.679,0.193 10 CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

As DTC B1422 is also output when the compressor drive belt is damaged or loose, inspect the belt before performing troubleshooting.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the intelligent tester to check if the CAN communication system is functioning normally.


Result
Result Proceed to
CAN DTC is not output A
CAN DTC is output (for LHD with Entry and Start System) B
CAN DTC is output (for LHD without Entry and Start System) C
CAN DTC is output (for RHD with Entry and Start System) D
CAN DTC is output (for RHD without Entry and Start System) E


A

2.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

B

C

D

E

2.INSPECT COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)
a.
E193115E01
2.569,0.858 2.989,1.033 0.420,0.174 10 SSR+ 0.444,0.849 0.836,1.008 0.392,0.158 10 SSR- 1.899,0.95 2.495,0.95 false 1.533,0.947 0.908,0.947 false

for 1GR-FE:

Remove the cooler compressor assembly (A/C lock sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 1GR-FE)>REMOVAL).


b.

for 1KD-FTV:

Remove the cooler compressor assembly (A/C lock sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR(for 1KD-FTV)>REMOVAL).


c.

for 2TR-FE:

Remove the cooler compressor assembly (A/C lock sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 2TR-FE)>REMOVAL).


d.

for 1GD-FTV:

Remove the cooler compressor assembly (A/C lock sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>COMPRESSOR (for 1GD-FTV)>REMOVAL).


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) 20°C (68°F) 160 to 320 Ω



Result
Result Proceed to
OK A
NG (for 1GR-FE) B
NG (for 1KD-FTV) C
NG (for 2TR-FE) D
NG (for 1GD-FTV) E


A

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)

B

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

C

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

D

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

E

REPLACE COOLER COMPRESSOR ASSEMBLY (A/C LOCK SENSOR)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER - A/C LOCK SENSOR)
a.

Disconnect the G25 amplifier connector.


b.

Disconnect the C39 sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-8 (LOCK) - C39-1 (SSR+) Always Below 1 Ω
G25-13 (SG-2) - C39-2 (SSR-) Always Below 1 Ω
G25-8 (LOCK) - Body ground Always 10 kΩ or higher
G25-13 (SG-2) - Body ground Always 10 kΩ or higher



Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C


A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR