Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 5L-E)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261182 COMPRESSOR(for 5L-E) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 5L-E)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the compressor with a new one, gradually release the refrigerant gas from the service valve and drain the following amount of oil from the new compressor before installation.

Standard:

(The amount of oil inside a new cooler compressor: 180 to 195 cc (6.1 to 6.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

Since compressor oil remains in the pipes of the vehicle, if a new compressor is installed without removing some oil from the compressor, the oil amount becomes excessive. Excessive oil prevents heat exchange in the refrigerant cycle and causes refrigeration system failure.

·

If the volume of oil remaining in the removed compressor is too small, check for oil leakage.

·

Be sure to use ND-OIL 8 for compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

E201485E02
2.438,2.917 2.813,3.094 0.375,0.177 10 false (A) 1 1.75,3.063 2.125,3.24 0.375,0.177 10 false (A) 2 0.615,2.25 0.75,2.427 0.135,0.177 10 false 3 0.302,2.146 0.438,2.302 0.135,0.156 10 false 4 0.458,1.698 0.583,1.875 0.125,0.177 10 false 5 0.177,1.49 0.313,1.677 0.135,0.188 10 false 6

a.

Temporarily install the cooler compressor with the 2 bolts.


b.

Temporarily install the idle pulley with the 4 bolts.


c.

Tighten the 6 bolts in the sequence shown in the illustration.

Torque:
for bolt A : 45 N*m (459 kgf*cm, 33 ft.*lbf)
except bolt A : 25 N*m (255 kgf*cm, 18 ft.*lbf)


d.

Connect the connector.


Hide 88704 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.

Remove the vinyl tape attached to the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the suction hose.


d.

Connect the suction hose to the compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Remove the vinyl tape attached to the hose.


b.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the compressor.

Compressor oil:

ND-OIL 8 or equivalent



c.

Install the O-ring to the discharge hose.


d.

Connect the discharge hose to the compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 17801 7.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 53292A 12.INSTALL UPPER RADIATOR SUPPORT SEAL