Home › Vehicle Exterior › WINDOW / GLASS › BACK DOOR GLASS(for Glass Hatch Type)
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261222 BACK DOOR GLASS(for Glass Hatch Type) A

WINDOW / GLASS  BACK DOOR GLASS(for Glass Hatch Type)  INSTALLATION  


PROCEDURE

Hide 68820C 1.INSTALL BACK DOOR HINGE ASSEMBLY LH

HINT:

Perform the following procedures if replacing the back door hinge assembly LH.


a.

Using a T30 "TORX" socket wrench, install the back door hinge with the 2 screws.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 68810D 2.INSTALL BACK DOOR HINGE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 64819B 3.INSTALL BACK WINDOW GLASS SPACER

HINT:

Perform the following procedures if replacing any back window glass spacer.


U115597E04
2.552,1.365 2.479,0.719 2.479,0.719 2.729,0.719 false 4.563,0.844 4.313,0.365 4.313,0.365 4.042,0.365 false 2.823,0.656 3.021,0.833 0.198,0.177 10 false *1 3.854,0.292 4.094,0.531 0.24,0.24 10 false *2 1.219,0.521 1.448,0.698 0.229,0.177 10 false a 0.958,1.688 1.135,1.865 0.177,0.177 10 false b 0.552,0.885 0.76,1.104 0.208,0.219 10 false c 0.823,0.667 1.031,0.865 0.208,0.198 10 false d 5.875,0.135 6.052,0.292 0.177,0.156 10 false a 6.125,1.313 6.281,1.479 0.156,0.167 10 false b 6.552,0.49 6.719,0.646 0.167,0.156 10 false c 6.271,0.281 6.458,0.49 0.188,0.208 10 false d

Text in Illustration
*1 No. 2 Back Window Glass Spacer *2 No. 1 Back Window Glass Spacer

a.

Apply Primer G to the window where the spacer will be installed.

Standard:
Area Specified Condition
a 88.2 mm (3.47 in.)
b 100.7 mm (3.94 in.)
c 73.7 mm (2.90 in.)
d 35.0 mm (1.37 in.)



b.
NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.



HINT:

If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer before it dries.



c.

Remove the peeling paper from a new spacer install the spacer to the back door glass at the location shown in the illustration.


Hide 69450D 4.INSTALL BACK WINDOW LOCK STRIKER ASSEMBLY

a.

Install the lock striker with the 2 nuts.


Hide 69415E 5.INSTALL BACK DOOR LOCK STRIKER COVER

a.

Attach the 3 claws to install the lock striker cover.


Hide 68678 6.INSTALL BACK DOOR WINDOW PROTECTOR

a.

Apply Primer G to the back window glass where the back door window protector will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new back door window protector. Install a back door window protector to the back window glass at the locations shown in the illustration.

B386627E01
0.045,0.014 0.390,0.324 0.345,0.310 10 *a 3.027,2.43 3.230,2.623 0.202,0.193 10 a 3.989,2.426 4.192,2.619 0.202,0.193 10 a

Text in Illustration
*a Backside - -

Standard:
Area Specified Condition
a 310.0 mm (12.20 in.)



Hide 67891C 7.INSTALL BACK DOOR SEAL LH

a.

Apply Primer G to the back window glass where the back door seal LH will be installed.

NOTICE:
·

Allow the primer to dry for 3 minutes or more.

·

Throw away any leftover primer.

·

Do not apply too much primer.




b.

Remove the peeling paper from a new back door seal LH. Install a back door seal LH to the back window glass at the locations shown in the illustration.

B386628E03
5.542,0.375 5.604,0.083 5.604,0.083 5.979,0.083 true 0.052,0 0.469,0.354 0.417,0.354 10 false *a 6,0.01 6.292,0.313 0.292,0.302 10 false *b 5.802,0.333 6.406,0.563 0.604,0.229 10 false a 6.052,2.969 6.323,3.24 0.271,0.271 10 false b 6.438,1.563 6.708,1.833 0.271,0.271 10 false c 4.135,1.083 4.385,1.375 0.25,0.292 10 false A 4.583,0.99 4.823,1.26 0.24,0.271 10 false A 5.927,1.417 6.313,1.677 0.385,0.26 10 false A - A

Text in Illustration
*a Backside *b R End

Standard:
Area Specified Condition
a 25.1 mm (0.99 in.)
b 3.1 mm (0.12 in.)
c 11.0 mm (0.43 in.)



Hide 67891A 8.INSTALL BACK DOOR SEAL RH

HINT:

Use the same procedure described for the back door seal LH.


Hide 68131 9.INSTALL BACK DOOR GLASS

a.

Install the back door glass with the 4 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 clamps and install the connector.


Hide 68940 10.INSTALL BACK WINDOW STAY ASSEMBLY LH

Hide 68930 11.INSTALL BACK WINDOW STAY ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 85110R 12.INSTALL REAR WIPER MOTOR ASSEMBLY

Hide 85241A 13.INSTALL REAR WIPER ARM

Hide 76085 14.INSTALL REAR SPOILER SUB-ASSEMBLY