If the manual up and down function operates normally but the auto up and down function does not, then fail-safe mode may be functioning.
If power window initialization has not been performed, the auto up and down function will not operate (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
If the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check that the "P Window Auto Up" and "P Window Auto Down" power window control system customize settings are "ON" before proceeding with work.
After the catch protection function operates, the auto operation is not performed the first time auto up is performed. All auto up operations performed after the first operate normally (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>CUSTOMIZE PARAMETERS).
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the pulse sensor built into the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) is malfunctioning, the power window control system enters fail-safe mode. The remote up and down and auto up and down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the power window regulator switch assembly at the auto up position, and opened manually by pushing down the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>FAIL-SAFE CHART).
Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P Door P/W Auto SW | Front passenger side power window auto up/down signal / ON or OFF | ON: Front passenger side power window auto up/down switch operated
OFF: Front passenger side power window regulator switch not operated |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Initialize the front power window regulator motor assembly RH (for LHD) or front power window regulator motor assembly LH (for RHD) (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
NEXT
Check that the front passenger door power window moves when the auto up and down function of the power window regulator switch assembly is operated (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK).
Front passenger door auto up and down function is normal.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).
Inspect the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION).
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Disconnect the J1 power window regulator switch assembly connector.
Disconnect the J7 front power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J1-8 (AUTO) - J7-4 (AUTO) | Always | Below 1 Ω |
| J1-1 (GND) - Body ground | Always | Below 1 Ω |
| J1-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the K10 power window regulator switch assembly connector.
Disconnect the K7 front power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-8 (AUTO) - K7-4 (AUTO) | Always | Below 1 Ω |
| K10-1 (GND) - Body ground | Always | Below 1 Ω |
| K10-8 (AUTO) - Body ground | Always | 10 kΩ or higher |
OK
NG