Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM U

WIPER / WASHER  WIPER AND WASHER SYSTEM  TERMINALS OF ECU  


CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (for Windshield Wiper Switch LH Side Type)


U170578E02
3.458,0.26 4,0.448 0.542,0.188 10 false G120

a.

Disconnect the G120 windshield wiper switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G120-11 (+B) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
G120-11 (+B) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
G120-7 (WIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
G120-7 (WIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
G120-9 (EW) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G120 windshield wiper switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G120-8 (WF) - Body ground B - Body ground Front washer motor output Front washer switch on Below 1 V
G120-8 (WF) - Body ground B - Body ground Front washer motor output Front washer switch off 11 to 14 V
G120-4 (SPD) - Body ground R - Body ground Speed signal Driving at approx. 20 km/h (12 mph) Pulse generation (See waveform 1)
G120-3 (TAIL) - Body ground V - Body ground Light control switch tail position signal input Light control switch in tail position 11 to 14 V
G120-3 (TAIL) - Body ground V - Body ground Light control switch tail position signal input Light control switch off Below 1 V
G120-2 (+1) - Body ground B - Body ground Front wiper motor LO speed signal circuit Front wiper motor in LO operation 11 to 14 V
G120-2 (+1) - Body ground B - Body ground Front wiper motor LO speed signal circuit Front wiper motor off Below 1 V
G120-1 (+2) - Body ground R - Body ground Front wiper motor HI speed signal circuit Front wiper motor in HI operation 11 to 14 V
G120-1 (+2) - Body ground R - Body ground Front wiper motor HI speed signal circuit Front wiper motor off Below 1 V
G120-10 (+S) - Body ground W - Body ground Front wiper motor operation signal Front wiper motor operates 11 to 14 V
G120-10 (+S) - Body ground W - Body ground Front wiper motor operation signal Front wiper motor off Below 1 V
G120-16 (C1R) - Body ground B - Body ground Rear wiper motor LO speed signal circuit Ignition switch ON, rear wiper switch LO Below 1 V
G120-16 (C1R) - Body ground B - Body ground Rear wiper motor LO speed signal circuit Ignition switch ON, rear wiper switch off 11 to 14 V
G120-18 (+1R) - Body ground R - Body ground Rear wiper motor HI speed signal circuit Ignition switch ON, rear wiper switch HI Below 1 V
G120-18 (+1R) - Body ground R - Body ground Rear wiper motor HI speed signal circuit Ignition switch ON, rear wiper switch off 11 to 14 V
G120-17 (WR) - Body ground V - Body ground Rear washer motor output Rear washer switch on Below 1 V
G120-17 (WR) - Body ground V - Body ground Rear washer motor output Rear washer switch off 11 to 14 V


e.
E149152E01
2.806,1.183 3.146,1.325 0.340,0.142 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G120-4 (SPD) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Driving at approx. 20 km/h (12 mph)



CHECK WINDSHIELD WIPER SWITCH ASSEMBLY (for Windshield Wiper Switch RH Side Type)


U170578E02
3.458,0.26 4,0.448 0.542,0.188 10 false G120

a.

Disconnect the G120 windshield wiper switch connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G120-17 (+B) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
G120-17 (+B) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
G120-3 (WIG) - Body ground G - Body ground Ignition switch power supply Ignition switch ON 11 to 14 V
G120-3 (WIG) - Body ground G - Body ground Ignition switch power supply Ignition switch off Below 1 V
G120-1 (EW) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the G120 windshield wiper switch assembly connector.


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G120-2 (WF) - Body ground B - Body ground Front washer motor output Front washer switch on Below 1 V
G120-2 (WF) - Body ground B - Body ground Front washer motor output Front washer switch off 11 to 14 V
G120-6 (SPD) - Body ground R - Body ground Speed signal Driving at approx. 20 km/h (12 mph) Pulse generation (See waveform 1)
G120-7 (TAIL) - Body ground V - Body ground Light control switch tail position signal input Light control switch in tail position 11 to 14 V
G120-7 (TAIL) - Body ground V - Body ground Light control switch tail position signal input Light control switch off Below 1 V
G120-8 (+1) - Body ground B - Body ground Front wiper motor LO speed signal circuit Front wiper motor in LO operation 11 to 14 V
G120-8 (+1) - Body ground B - Body ground Front wiper motor LO speed signal circuit Front wiper motor off Below 1 V
G120-9 (+2) - Body ground R - Body ground Front wiper motor HI speed signal circuit Front wiper motor in HI operation 11 to 14 V
G120-9 (+2) - Body ground R - Body ground Front wiper motor HI speed signal circuit Front wiper motor off Below 1 V
G120-18 (+S) - Body ground W - Body ground Front wiper motor operation signal Front wiper motor operates 11 to 14 V
G120-18 (+S) - Body ground W - Body ground Front wiper motor operation signal Front wiper motor off Below 1 V
G120-12 (C1R) - Body ground B - Body ground Rear wiper motor LO speed signal circuit Ignition switch ON, rear wiper switch LO Below 1 V
G120-12 (C1R) - Body ground B - Body ground Rear wiper motor LO speed signal circuit Ignition switch ON, rear wiper switch off 11 to 14 V
G120-10 (+1R) - Body ground R - Body ground Rear wiper motor HI speed signal circuit Ignition switch ON, rear wiper switch HI Below 1 V
G120-10 (+1R) - Body ground R - Body ground Rear wiper motor HI speed signal circuit Ignition switch ON, rear wiper switch off 11 to 14 V
G120-11 (WR) - Body ground V - Body ground Rear washer motor output Rear washer switch on Below 1 V
G120-11 (WR) - Body ground V - Body ground Rear washer motor output Rear washer switch off 11 to 14 V


e.
E149152E01
2.806,1.183 3.146,1.325 0.340,0.142 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G120-6 (SPD) - Body ground
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Driving at approx. 20 km/h (12 mph)



CHECK HEADLIGHT CLEANER CONTROL RELAY


U170587E02
3.313,0.24 3.698,0.448 0.385,0.208 10 false A38

a.

Disconnect the A38 headlight cleaner control relay connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A38-1 (HDLO) - A38-4 (E) V - W-B Low beam headlight signal Headlight dimmer switch in head 11 to 14 V
A38-1 (HDLO) - A38-4 (E) V - W-B Low beam headlight signal Headlight dimmer switch not in head Below 1 V
A38-3 (IG) - A38-4 (E) L - W-B Ignition switch power supply Ignition switch ON 11 to 14 V
A38-3 (IG) - A38-4 (E) L - W-B Ignition switch power supply Ignition switch off Below 1 V
A38-4 (E) - Body ground W-B - Body ground Body ground Always Below 1 Ω
A38-5 (FRWA) - A38-4 (E) B - W-B Front washer switch operation signal Front washer motor switch on Below 1 V
A38-5 (FRWA) - A38-4 (E) B - W-B Front washer switch operation signal Front washer motor switch off 11 to 14 V



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169674E01
0.25,1.036 0.555,1.192 0.305,0.156 10 2I*A 0.201,1.191 0.555,1.346 0.354,0.156 10 2H*B 1.086,3.831 1.367,3.986 0.280,0.156 10 G63 0.901,2.168 1.109,2.324 0.208,0.156 10 2F 5.866,1.489 6.074,1.645 0.208,0.156 10 2D 5.866,2.192 6.074,2.348 0.208,0.156 10 2A 1.076,2.708 1.284,2.864 0.208,0.156 10 2K 3.75,1.293 3.869,1.435 0.119,0.142 10 A 1.961,1.157 2.291,1.299 0.330,0.142 10 G65 1.623,1.465 1.866,1.222 1.866,1.222 1.944,1.222 false 1.961,1.514 2.277,1.656 0.316,0.142 10 G64 1.623,1.822 1.866,1.58 1.866,1.58 1.944,1.58 false 1.961,1.832 2.277,1.974 0.316,0.142 10 G63 1.623,2.14 1.866,1.897 1.866,1.897 1.944,1.897 false 3.58,3.831 3.875,3.986 0.295,0.156 10 G64 0.594,5.151 0.752,5.307 0.159,0.156 10 2I 1.518,5.151 1.723,5.307 0.205,0.156 10 2H 1.881,6.368 2.095,6.524 0.214,0.156 10 2D 4.939,6.368 5.153,6.524 0.214,0.156 10 2A 3.509,7.639 3.640,7.795 0.131,0.156 10 A 3.95,5.141 4.150,5.297 0.200,0.156 10 2F 5.896,5.141 6.096,5.297 0.200,0.156 10 2K 5.901,3.831 6.200,3.986 0.299,0.156 10 G65 0.87,5.146 1.102,5.321 0.232,0.174 10 *A 1.851,5.146 2.083,5.321 0.232,0.174 10 *B 0.996,1.546 0.658,1.104 0.658,1.104 0.522,1.104 false

Text in Illustration
*A for LHD *B for RHD

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A-30 (BECU) - Body ground - Battery power supply Always 11 to 14 V
A-31 (ALTB) - Body ground - Battery power supply Always 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch ON 11 to 14 V
A-32 (IG) - Body ground - Ignition switch power supply Ignition switch off Below 1 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
A-29 (ACC) - Body ground - ACC power supply Ignition switch off Below 1 V
A-11 (GND1) - Body ground - Ground Always Below 1 Ω
G63-3 (GND2) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Install the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>INSTALLATION).


d.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G63-16 (HDLO) - G63-3 (GND2) V - W-B Low beam headlight signal Headlight dimmer switch in head 11 to 14 V
G63-16 (HDLO) - G63-3 (GND2) V - W-B Low beam headlight signal Headlight dimmer switch not in head Below 1 V
G64-19 (BCTY) - G63-3 (GND2) G - W-B Back door courtesy light switch input Back door open Below 1 V
G64-19 (BCTY) - G63-3 (GND2) G - W-B Back door courtesy light switch input Back door closed Pulse generation (See waveform 1 or 2)
G64-1 (GCTY) - G63-3 (GND2) V - W-B Glass hatch courtesy switch input Glass hatch open Below 1 V
G64-1 (GCTY) - G63-3 (GND2) V - W-B Glass hatch courtesy switch input Ignition switch off, all doors closed and glass hatch closed Pulse generation (See waveform 3 or 4)
G63-20 (RWMR) - G63-3 (GND2) B - W-B Rear wiper power supply input Ignition switch ON, glass hatch open Below 1 V
G63-20 (RWMR) - G63-3 (GND2) B - W-B Rear wiper power supply input Ignition switch ON, glass hatch closed 11 to 14 V


e.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

Waveform 1 (Reference)
Item Content
Terminal No. (Symbol) G64-19 (BCTY) - G63-3 (GND2)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed


f.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 2.

Waveform 2 (Reference)
Item Content
Terminal No. (Symbol) G64-19 (BCTY) - G63-3 (GND2)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Back door closed


g.
B199631E01
0.166,0.956 0.503,1.113 0.337,0.156 10 GND

Using an oscilloscope, check waveform 3.

Waveform 3 (Reference)
Item Content
Terminal No. (Symbol) G64-1 (GCTY) - G63-3 (GND2)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and glass hatch closed


h.
B199632E01
0.16,0.946 0.507,1.110 0.347,0.165 10 GND

Using an oscilloscope, check waveform 4.

Waveform 4 (Reference)
Item Content
Terminal No. (Symbol) G64-1 (GCTY) - G63-3 (GND2)
Tool Setting 5 V/DIV., 20 ms/DIV.
Condition Ignition switch off, all doors closed and glass hatch closed