Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261257 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rear Wiper does not Operate  


DESCRIPTION

When the glass hatch is open, the rear wiper system cuts off the power supply to prevent the rear wiper and rear washer from operating.

WIRING DIAGRAM

B243376E11
0.979,5.26 2.875,5.708 1.896,0.448 10 false Rear Wiper Motor Assembly 5.427,5.573 7.115,6.021 1.688,0.448 10 false Windshield Wiper Switch Assembly 5.135,4.542 5.813,4.729 0.677,0.188 10 false 9*1, 1*2 5,4.073 5.792,4.302 0.792,0.229 10 false 16*1, 12*2 4.979,3.594 5.771,3.792 0.792,0.198 10 false 18*1, 10*2 5.771,4.167 6.104,4.323 0.333,0.156 10 false C1R 5.771,3.698 6.104,3.854 0.333,0.156 10 false +1R 5.771,4.604 6.052,4.76 0.281,0.156 10 false EW 2.031,3.219 2.24,3.406 0.208,0.188 10 false +B 2.031,3.688 2.24,3.875 0.208,0.188 10 false LS 2.031,4.146 2.24,4.333 0.208,0.188 10 false C1 2.115,4.625 2.24,4.813 0.125,0.188 10 false E 2.385,3.115 2.5,3.292 0.115,0.177 10 false 5 2.385,3.604 2.5,3.781 0.115,0.177 10 false 2 2.385,4.063 2.5,4.24 0.115,0.177 10 false 4 2.385,4.542 2.5,4.719 0.115,0.177 10 false 3 2.927,3.354 3.458,3.51 0.531,0.156 10 false WIP RR 0.448,1.542 1.844,1.729 1.396,0.188 10 false from IG1 NO.2 Relay 0.99,2.292 2.021,2.667 1.031,0.375 10 false from Battery 2.854,1.698 3.521,1.854 0.667,0.156 10 false WASHER 2.708,2.438 3.625,2.594 0.917,0.156 10 false WIP WSH RR 4.094,2.75 4.979,2.906 0.885,0.156 10 false WASHER RR 4.063,1.448 4.177,1.594 0.115,0.146 10 false 2 4.063,2.188 4.177,2.333 0.115,0.146 10 false 5 4.896,1.448 5.01,1.594 0.115,0.146 10 false 1 4.896,2.188 5.01,2.333 0.115,0.146 10 false 3 5.75,1.552 6.25,1.698 0.5,0.146 10 false RWMR 5.375,1.552 5.792,1.833 0.417,0.281 10 false G63 5.469,0.906 5.708,1.156 0.24,0.25 10 false A 5.74,0.906 6.156,1.063 0.417,0.156 10 false GND1 5.448,1.323 5.625,1.479 0.177,0.156 10 false 20 5.448,0.688 5.625,0.833 0.177,0.146 10 false 11 5.354,2.146 7.031,2.49 1.677,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.188,0.438 2.927,0.938 2.74,0.5 10 false Back Window Lock Assembly (Glass Hatch Courtesy Light Switch) 5.406,5.385 6.073,5.594 0.667,0.208 10 false G120 0.979,5.104 1.281,5.323 0.302,0.219 10 false Y1 0.115,0.094 1.719,0.365 1.604,0.271 12 false w/ Rain Sensor: 0.115,5.969 6.844,6.167 6.729,0.198 10 false *1: for Windshield Wiper Switch LH Side Type 0.125,6.375 6.854,6.573 6.729,0.198 10 false 2: for Windshield Wiper Switch RH Side Type

B243376E12
1.031,5.396 2.833,5.75 1.802,0.354 10 false Rear Wiper Motor Assembly 5.427,5.573 7.031,5.917 1.604,0.344 10 false Windshield Wiper Switch Assembly 5.563,4.542 5.677,4.698 0.115,0.156 10 false 1 5.521,4.073 5.75,4.229 0.229,0.156 10 false 12 5.51,3.563 5.688,3.719 0.177,0.156 10 false 10 5.771,4.167 6.104,4.323 0.333,0.156 10 false C1R 5.771,3.698 6.104,3.854 0.333,0.156 10 false +1R 5.771,4.604 6.052,4.76 0.281,0.156 10 false EW 2.031,3.219 2.24,3.406 0.208,0.188 10 false +B 2.031,3.688 2.24,3.875 0.208,0.188 10 false LS 2.031,4.146 2.24,4.333 0.208,0.188 10 false C1 2.115,4.625 2.24,4.813 0.125,0.188 10 false E 2.385,3.115 2.5,3.292 0.115,0.177 10 false 5 2.385,3.604 2.5,3.781 0.115,0.177 10 false 2 2.385,4.063 2.5,4.24 0.115,0.177 10 false 4 2.385,4.542 2.5,4.719 0.115,0.177 10 false 3 2.927,3.354 3.458,3.51 0.531,0.156 10 false WIP RR 0.406,1.51 1.802,1.698 1.396,0.188 10 false from IG1 NO.2 Relay 0.99,2.271 1.792,2.458 0.802,0.188 10 false from Battery 2.854,1.698 3.521,1.854 0.667,0.156 10 false WASHER 2.708,2.438 3.625,2.594 0.917,0.156 10 false WIP WSH RR 4.094,2.75 4.979,2.906 0.885,0.156 10 false WASHER RR 4.063,1.448 4.177,1.583 0.115,0.135 10 false 2 4.063,2.188 4.177,2.323 0.115,0.135 10 false 5 4.896,1.448 5.01,1.583 0.115,0.135 10 false 1 4.896,2.188 5.01,2.323 0.115,0.135 10 false 3 5.75,1.552 6.25,1.698 0.5,0.146 10 false PWMR 5.396,1.531 5.708,1.688 0.313,0.156 10 false G46 5.49,0.885 5.604,1.042 0.115,0.156 10 false A 5.74,0.906 6.156,1.063 0.417,0.156 10 false GND1 5.448,1.323 5.625,1.479 0.177,0.156 10 false 20 5.448,0.688 5.625,0.833 0.177,0.146 10 false 11 5.354,2.146 7.031,2.49 1.677,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.24,0.375 2.927,0.781 2.688,0.406 10 false Back Window Lock Assembly (Glass Hatch Courtesy Light Switch) 5.406,5.385 5.802,5.583 0.396,0.198 10 false G43 1.052,5.177 1.365,5.375 0.313,0.198 10 false Y1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (GLASS HATCH COURTESY SWITCH)
a.

Use the Data List to check if the glass hatch opener is functioning properly (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).


Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Glass Hatch Courtesy Switch Glass hatch courtesy switch signal / ON or OFF ON: Glass hatch open
OFF: Glass hatch closed
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.



OK

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER MOTOR)

NG

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (REAR WIPER MOTOR)
a.

Using the intelligent tester, perform the Active Test (See page Vehicle Exterior>WIPER / WASHER>WIPER AND WASHER SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Rear Wiper Power Supply WASHER RR relay operation ON/OFF -

OK:

Rear wiper motor operates.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT WASHER RR RELAY
3.INSPECT WASHER RR RELAY
a.
B242124E01
1.292,0.74 1.584,0.185 1.584,0.185 1.773,0.185 false 0.708,0.74 1,0.185 1,0.185 1.189,0.185 false 1.789,0.082 1.924,0.258 0.135,0.177 10 2 1.651,1.353 1.763,1.500 0.112,0.147 10 5 1.222,0.082 1.357,0.258 0.135,0.177 10 1 0.98,1.159 1.533,1.457 1.533,1.457 1.621,1.457 false 1.651,1.835 1.763,1.981 0.112,0.147 10 3 0.98,1.64 1.533,1.938 1.533,1.938 1.621,1.938 false

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - BATTERY)

NG

REPLACE WASHER RR RELAY

4.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - BATTERY)
a.
B242123E01
0.349,0.148 0.526,0.311 0.177,0.163 10 *a

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
WASHER RR relay terminal 2 - Body ground Ignition switch ON 11 to 14 V
WASHER RR relay terminal 2 - Body ground Ignition switch off Below 1 V
WASHER RR relay terminal 5 - Body ground Always 11 to 14 V
WASHER RR relay terminal 5 - Body ground Always Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to WASHER RR Relay)



OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - RR WASHER RELAY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - RR WASHER RELAY AND BODY GROUND)
a.

Remove the WASHER RR relay from the engine room relay block, junction block.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G63-20 (RWMR) - WASHER RR relay terminal 1 Always Below 1 Ω
A-11 (GND1) - Body ground Always Below 1 Ω
G63-20 (RWMR) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - REAR WIPER MOTOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (WASHER RR RELAY - REAR WIPER MOTOR ASSEMBLY)
a.

Disconnect the Y1 rear wiper motor connector.


b.

Remove the WASHER RR relay from the engine room relay block, junction block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-5 (+B) - WASHER RR relay terminal 3 Always Below 1 Ω
Y1-5 (+B) - Body ground Always 10 kΩ or higher




OK

7.INSPECT REAR WIPER MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT REAR WIPER MOTOR ASSEMBLY
a.
E196889E06
1.405,0.935 1.068,0.598 1.068,0.598 0.941,0.598 false 2.344,0.407 2.536,0.563 0.192,0.156 10 LS 2.369,1.638 2.579,1.794 0.210,0.156 10 C1 0.809,0.521 0.928,0.677 0.119,0.156 10 E 0.809,1.655 1.017,1.811 0.208,0.156 10 +B 1.801,0.947 2.162,0.497 2.162,0.497 2.299,0.497 false 1.846,1.287 2.207,1.737 2.207,1.737 2.344,1.737 false 1.603,1.288 1.225,1.734 1.225,1.734 1.044,1.734 false

Remove the rear wiper motor (See page Vehicle Exterior>WIPER / WASHER>REAR WIPER MOTOR>REMOVAL).


b.

Check that the rear wiper motor assembly operates when the battery voltage is applied between the terminals.

OK:
Tester Connection Specified Condition
Battery positive (+) → 5 (+B)
Battery negative (-) → 2 (LS)
Battery negative (-) → 3 (E)
Motor operates at low speed (LO)
Battery positive (+) → 5 (+B)
Battery negative (-) → 4 (C1)
Battery negative (-) → 3 (E)
Rear wiper motor operates intermittently




OK

8.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)

NG

REPLACE REAR WIPER MOTOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (REAR WIPER MOTOR ASSEMBLY - BODY GROUND)
a.
U116476E01
2.529,0.551 2.655,0.705 0.126,0.154 10 E 1.971,1.022 2.358,0.633 2.358,0.633 2.526,0.633 false 0.112,0.047 0.306,0.230 0.194,0.184 10 *a 0.614,1.026 0.807,1.170 0.193,0.144 10 Y1

Disconnect the Y1 rear wiper motor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-3 (E) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Rear Wiper Motor Assembly)



OK

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY
a.

Remove the windshield wiper switch connector (See page Vehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL).

U169793E01
0.794,0.79 0.552,0.556 0.552,0.556 0.482,0.556 false 0.794,0.99 0.552,1.224 0.552,1.224 0.482,1.224 false 0.042,1.157 0.475,1.299 0.434,0.142 10 +1R*A 0.066,0.485 0.482,0.627 0.416,0.142 10 EW*A 1.897,0.976 2.111,1.238 2.111,1.238 2.181,1.238 false 1.539,1.057 1.652,1.439 1.652,1.439 1.725,1.439 false 1.123,1.057 0.996,1.439 0.996,1.439 0.922,1.439 false 1.744,1.374 2.216,1.516 0.472,0.142 10 C1R*B 2.199,1.168 2.633,1.310 0.434,0.142 10 +1R*B 0.476,1.367 0.937,1.509 0.461,0.142 10 C1R*A 1.869,0.79 2.111,0.416 2.111,0.416 2.181,0.416 false 2.185,0.345 2.591,0.487 0.406,0.142 10 EW*B 6.138,0.251 6.254,0.396 0.117,0.145 10 B 3.492,0.225 3.609,0.370 0.117,0.145 10 B 6.122,0.987 6.257,1.384 6.257,1.384 6.327,1.384 false 6.015,0.996 5.851,1.381 5.851,1.381 5.783,1.381 false 6.34,1.314 6.796,1.463 0.456,0.149 10 C1R*B 6.746,0.319 7.136,0.468 0.390,0.149 10 EW*B 2.644,0.307 3.035,0.456 0.391,0.149 10 EW*A 5.345,1.314 5.788,1.463 0.442,0.149 10 +1R*B 3.7,0.974 3.836,1.385 3.836,1.385 3.906,1.385 false 3.599,0.961 3.429,1.383 3.429,1.383 3.362,1.383 false 2.914,1.316 3.366,1.465 0.452,0.149 10 C1R*A 3.928,1.311 4.412,1.460 0.484,0.149 10 +1R*A 6.205,0.773 6.624,0.391 6.624,0.391 6.729,0.391 false 3.533,0.762 3.088,0.375 3.088,0.375 3.018,0.375 false 3.736,0.217 3.934,0.372 0.199,0.156 10 *D 6.384,0.245 6.582,0.400 0.199,0.156 10 *D 1.228,0.245 1.426,0.400 0.199,0.156 10 *C


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Windshield Wiper Switch LH Side Type:
w/ Rain Sensor
Tester Connection Switch Condition Specified Condition
16 (C1R) - 9 (EW) OFF 10 kΩ or higher
18 (+1R) - 9 (EW) OFF 10 kΩ or higher
16 (C1R) - 9 (EW) LO Below 1 Ω
18 (+1R) - 9 (EW) HI Below 1 Ω

w/o Rain Sensor
Tester Connection Switch Condition Specified Condition
B-5 (C1R) - B-2 (EW) OFF 10 kΩ or higher
B-4 (+1R) - B-2 (EW) OFF 10 kΩ or higher
B-5 (C1R) - B-2 (EW) LO Below 1 Ω
B-4 (+1R) - B-2 (EW) HI Below 1 Ω

for Windshield Wiper Switch RH Side Type:
w/ Rain Sensor
Tester Connection Switch Condition Specified Condition
12 (C1R) - 1 (EW) OFF 10 kΩ or higher
10 (+1R) - 1 (EW) OFF 10 kΩ or higher
12 (C1R) - 1 (EW) LO Below 1 Ω
10 (+1R) - 1 (EW) HI Below 1 Ω

w/o Rain Sensor
Tester Connection Switch Condition Specified Condition
B-6 (C1R) - B-2 (EW) OFF 10 kΩ or higher
B-7 (+1R) - B-2 (EW) OFF 10 kΩ or higher
B-6 (C1R) - B-2 (EW) LO Below 1 Ω
B-7 (+1R) - B-2 (EW) HI Below 1 Ω


Text in Illustration
*A for Windshield Wiper Switch LH Side Type
*B for Windshield Wiper Switch RH Side Type
*C w/ Rain Sensor
*D w/o Rain Sensor



OK

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER SWITCH ASSEMBLY - REAR WIPER MOTOR ASSEMBLY AND BODY GROUND)
a.

for Windshield Wiper Switch LH Side Type:

i.

Disconnect the Y1 rear wiper motor connector.


ii.

Disconnect the G120 or G43 windshield wiper switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rain Sensor
Tester Connection Condition Specified Condition
Y1-2 (LS) - G120-18 (+1R) Always Below 1 Ω
Y1-4 (C1) - G120-16 (C1R) Always Below 1 Ω
G120-9 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher

w/o Rain Sensor
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-4 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-5 (C1R) Always Below 1 Ω
G43-2 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher




b.

for Windshield Wiper Switch RH Side Type:

i.

Disconnect the Y1 rear wiper motor connector.


ii.

Disconnect the G120 or G43 windshield wiper switch connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/ Rain Sensor
Tester Connection Condition Specified Condition
Y1-2 (LS) - G120-10 (+1R) Always Below 1 Ω
Y1-4 (C1) - G120-12 (C1R) Always Below 1 Ω
G120-1 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher

w/o Rain Sensor
Tester Connection Condition Specified Condition
Y1-2 (LS) - G43-7 (+1R) Always Below 1 Ω
Y1-4 (C1) - G43-6 (C1R) Always Below 1 Ω
G43-2 (EW) - Body ground Always Below 1 Ω
Y1-2 (LS) - Body ground Always 10 kΩ or higher
Y1-4 (C1) - Body ground Always 10 kΩ or higher





OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR