Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM27T0E _59 Vehicle Exterior _053746 WIPER / WASHER _0261259 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110R 1.INSTALL REAR WIPER MOTOR ASSEMBLY

a.

Attach the 2 guides and temporarily install the rear wiper motor assembly with the 3 bolts.


b.

Tighten the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Connect the connector.


Hide 85241A 2.INSTALL REAR WIPER ARM

a.
E199088E02
1.511,1.508 1.688,1.707 0.177,0.199 10 *1 0.921,1.318 1.185,1.582 1.185,1.582 1.467,1.582 false

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Pivot Serrations


b.
E199087E01
0.363,0.592 0.622,0.817 0.260,0.224 10 *2 2.782,0.868 3.042,1.093 0.260,0.224 10 *1 0.581,0.696 0.974,0.696 0.974,0.696 1.219,0.942 false 2.742,0.947 2.578,0.947 2.578,0.947 2.18,1.231 false

Clean the wiper pivot serrations with a wire brush.

Text in Illustration
*1 Wiper Pivot Serrations
*2 Wire Brush


c.

Operate the rear wiper and stop the rear wiper motor at the automatic stop position.

HINT:

The wiper motor does not operate if the back door and back door glass are not closed.



d.
E198991E02
2.042,1.354 1.885,1.354 1.885,1.354 1.792,1.708 false 1.031,1.333 1.167,1.333 1.167,1.333 1.24,1.417 false 1.031,2.125 1.188,2.125 1.188,2.125 1.323,2.094 false 2.042,3.625 1.896,3.625 1.896,3.625 1.781,3.979 false 1.01,3.604 1.135,3.604 1.135,3.604 1.219,3.688 false 1.031,4.448 1.198,4.448 1.198,4.448 1.323,4.417 false 0.052,0.063 0.323,0.292 0.271,0.229 10 false *A 1.021,1.594 1.177,1.823 0.156,0.229 12 false a 0.833,1.229 1.031,1.458 0.198,0.229 12 false *a 2.083,1.25 2.281,1.479 0.198,0.229 12 false *1 0.823,2.01 1.021,2.24 0.198,0.229 12 false *b 1.042,1.792 1.156,1.979 0.115,0.188 12 false b 0.052,2.323 0.323,2.552 0.271,0.229 10 false *B 1.01,3.854 1.167,4.083 0.156,0.229 12 false a 0.833,3.521 1.031,3.75 0.198,0.229 12 false *a 2.073,3.542 2.271,3.771 0.198,0.229 12 false *1 0.833,4.344 1.031,4.573 0.198,0.229 12 false *b 1.031,4.083 1.146,4.271 0.115,0.188 12 false b

Align the blade tip with the mark on the glass as shown in the illustration.

Standard:
Area Standard Condition
a 10.0 mm (0.394 in.)
b 10.0 mm (0.394 in.)


Text in Illustration
*A w/o Back Door Tire Carrier
*B w/ Back Door Tire Carrier
*1 Ceramic Dot
*a Upper Limit
*b Lower Limit


e.

Install the rear wiper arm and blade assembly with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



Hide 85035R 3.INSTALL REAR WASHER NOZZLE SUB-ASSEMBLY

Hide 76085 4.INSTALL REAR SPOILER SUB-ASSEMBLY

a.

w/o Back Door Tire Carrier:

Install the rear spoiler sub-assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR SPOILER(w/o Tire Carrier)>INSTALLATION).


b.

w/ Back Door Tire Carrier:

Install the rear spoiler sub-assembly (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>REAR SPOILER(w/ Tire Carrier)>INSTALLATION).


Hide 76893 6.INSTALL REAR NO. 1 SPOILER COVER (w/o Back Door Tire Carrier)

Hide 67938A 7.INSTALL BACK DOOR SIDE GARNISH LH (w/ Back Door Tire Carrier)

Hide 67937B 8.INSTALL BACK DOOR SIDE GARNISH RH (w/ Back Door Tire Carrier)

Hide 67939B 9.INSTALL BACK DOOR CENTER GARNISH (w/ Back Door Tire Carrier)