Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1572  Microphone Error  


DESCRIPTION

This DTC is stored when a microphone signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1572 Microphone Error Current at terminal MCVD exceeds the malfunction threshold for 20 seconds while the ignition switch is ON.
·

Telematics transceiver

·

Map light assembly (telephone microphone assembly)

·

Wire harness or connector



WIRING DIAGRAM

E355978E03
0.365,2.042 1.771,2.438 1.406,0.396 10 false Telephone Microphone Assembly 1.49,0.479 2.021,0.719 0.531,0.24 10 false MACC 1.521,0.958 2.052,1.198 0.531,0.24 10 false MCO+ 1.563,1.438 2.094,1.677 0.531,0.24 10 false MCO- 3.135,2.208 3.344,2.427 0.208,0.219 10 false * 4.677,2.208 4.885,2.427 0.208,0.219 10 false * 5.688,2.771 7.156,3.01 1.469,0.24 10 false Telematics Transceiver 5.677,2.583 6.208,2.823 0.531,0.24 10 false G187 0.656,0.594 1.188,0.833 0.531,0.24 10 false MACC 0.74,1.073 1.271,1.313 0.531,0.24 10 false MIC+ 0.76,1.531 1.292,1.771 0.531,0.24 10 false MIC- 1.177,0.521 1.365,0.74 0.188,0.219 10 false 5 1.188,0.99 1.375,1.208 0.188,0.219 10 false 3 1.198,1.458 1.385,1.677 0.188,0.219 10 false 2 2.042,0.51 2.26,0.729 0.219,0.219 10 false 11 2.042,0.979 2.26,1.198 0.219,0.219 10 false 12 2.063,1.458 2.281,1.677 0.219,0.219 10 false 13 5.625,0.51 5.844,0.729 0.219,0.219 10 false 33 5.625,0.979 5.844,1.198 0.219,0.219 10 false 34 5.635,1.448 5.854,1.667 0.219,0.219 10 false 35 5.656,1.917 5.875,2.135 0.219,0.219 10 false 32 5.917,0.604 6.448,0.844 0.531,0.24 10 false MCVD 5.917,1.083 6.448,1.323 0.531,0.24 10 false MCI+ 5.917,1.531 6.448,1.771 0.531,0.24 10 false MCI- 5.906,2.021 6.438,2.26 0.531,0.24 10 false SGND 0.302,3.385 1.99,3.583 1.688,0.198 10 false *: Shielded 0.365,3.042 1.781,3.292 1.417,0.25 10 false Map Light Assembly 0.354,2.885 0.885,3.125 0.531,0.24 10 false W7

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the G187 telematics transceiver connector.


b.

Disconnect the W7 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-33 (MCVD) - W7-11 (MACC) Always Below 1 Ω
G187-34 (MCI+) - W7-12 (MCO+) Always Below 1 Ω
G187-35 (MCI-) - W7-13 (MCO-) Always Below 1 Ω
G187-33 (MCVD) or W7-11 (MACC) - Body ground Always 10 kΩ or higher
G187-34 (MCI+) or W7-12 (MCO+) - Body ground Always 10 kΩ or higher
G187-35 (MCI-) or W7-13 (MCO-) - Body ground Always 10 kΩ or higher
G187-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly.

Click hereVehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL


b.

Remove the telephone microphone assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL


c.
E355979C02
0.094,0.854 0.479,1.135 0.385,0.281 0.344,2.396 0.729,2.677 0.385,0.281 1.229,0.958 1.875,0.438 1.875,0.438 2.052,0.438 true 0.948,0.979 0.823,0.198 0.823,0.198 1,0.198 true 2.26,2.688 2.417,3.01 2.417,3.01 2.573,3.01 true 1.74,2.698 2.125,3.198 2.125,3.198 2.302,3.198 true 1.083,0.979 1.563,0.219 1.563,0.219 1.74,0.219 true 1.448,2.708 1.521,3.24 1.521,3.24 1.698,3.24 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 0.24,0.906 0.448,1.125 0.208,0.219 10 false A 0.49,2.458 0.698,2.677 0.208,0.219 10 false B 2.615,2.927 3.052,3.135 0.438,0.208 10 false MACC 2.104,0.365 2.542,0.573 0.438,0.208 10 false MACC 1.813,0.146 2.292,0.365 0.479,0.219 10 false MCO+ 1.063,0.115 1.542,0.333 0.479,0.219 10 false MCO- 2.344,3.115 2.823,3.333 0.479,0.219 10 false MIC+ 1.76,3.156 2.24,3.375 0.479,0.219 10 false MIC-
*a Component without harness connected
(Map Light Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-11 (MACC) - B-5 (MACC) Always Below 1 Ω
A-12 (MCO+) - B-3 (MIC+) Always Below 1 Ω
A-13 (MCO-) - B-2 (MIC-) Always Below 1 Ω
A-11 (MACC) - A-12 (MCO+) Always 10 kΩ or higher
A-11 (MACC) - A-13 (MCO-) Always 10 kΩ or higher
A-12 (MCO+) - A-13 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE AMPLIFIER>REMOVAL



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

5.REPLACE TELEMATICS TRANSCEIVER
5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT