These DTCs are stored when a malfunction occurs in the telephone antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1573 | Short in Telephone Antenna Circuit | Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
No. 2 antenna cord sub-assembly ·
Telephone antenna cord sub-assembly ·
Harness or connector |
| B15CB | Telephone Antenna Disconnected | Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
No. 2 antenna cord sub-assembly ·
Telephone antenna cord sub-assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the telephone antenna assembly.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
| *a | Telephone Antenna Assembly |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 - 4a | Always | 4 to 11 kΩ |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the antenna connector from the telephone antenna assembly.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
| *a | Front view of wire harness connector
(to Telephone Antenna Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-4 - B-3 | Always | Below 1 Ω |
| A-4a - B-3a | Always | Below 1 Ω |
| A-4 or B-3 - Body ground | Always | 10 kΩ or higher |
| A-4a or B-3a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the antenna connector from the telephone antenna cord sub-assembly.
Disconnect the antenna connector from the wire harness.
| *a | Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C-3 - D-3 (TEL1) | Always | Below 1 Ω |
| C-3a - D-3a | Always | Below 1 Ω |
| C-3 or D-3 (TEL1) - Body ground | Always | 10 kΩ or higher |
| C-3a or D-3a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H81 No. 2 antenna cord sub-assembly connector from the instrument panel wire.
Disconnect the H83 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H81-3 (TEL1) - H83-1 (TEL2) | Always | Below 1 Ω |
| H81-3 (TEL1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT