Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.08–2017.08
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C0  Short in GPS Antenna  B15C1  Open in GPS Antenna  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 Short in GPS Antenna Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Short circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly


B15C1 Open in GPS Antenna Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the ignition switch is ON.
(Open circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

No. 2 antenna cord sub-assembly

·

Telephone antenna cord sub-assembly



WIRING DIAGRAM

E350969E04
5.708,2.531 7.156,2.781 1.448,0.25 10 false Telematics Transceiver 0.208,2.302 1.396,2.708 1.188,0.406 10 false Telephone Antenna Assembly 1.552,2.448 3.094,2.844 1.542,0.396 10 false Telephone Antenna Cord Sub-assembly 3.583,2.469 4.844,2.844 1.26,0.375 10 false No. 2 Antenna Cord Sub-assembly 4.323,1.24 4.625,1.448 0.302,0.208 10 false D-2 4.271,1.75 4.615,2 0.344,0.25 10 false D-2a 3.542,1.24 3.844,1.448 0.302,0.208 10 false C-2 3.552,1.74 3.917,1.948 0.365,0.208 10 false C-2a 2.573,1.24 2.875,1.448 0.302,0.208 10 false B-2 2.51,1.74 2.833,1.948 0.323,0.208 10 false B-2a 1.385,1.24 1.688,1.448 0.302,0.208 10 false A-2 1.385,1.74 1.708,1.948 0.323,0.208 10 false A-2a 5.167,1.146 5.323,1.344 0.156,0.198 10 false 2 5.688,1.25 5.844,1.448 0.156,0.198 10 false 1 5.083,1.354 5.396,1.552 0.313,0.198 10 false H81 4.625,1.354 5.042,1.583 0.417,0.229 10 false GPS1 5.885,1.354 6.292,1.573 0.406,0.219 10 false GPS2 5.708,2.365 6.167,2.563 0.458,0.198 10 false H82

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
2.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.
E350951C15
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.26,1.313 1.677,1.271 true 1.063,3.417 1.594,3.583 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.083,1.219 1.396,1.417 0.313,0.198 10 false 2a 0.865,3.323 1.177,3.521 0.313,0.198 10 false 2a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.208,2.656 0.521,2.854 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 or B-2 - Body ground Always 10 kΩ or higher
A-2a or B-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT NO.2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY

3.INSPECT NO.2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E350952C02
1.583,0.396 2.021,0.677 0.438,0.281 1.667,2.615 2.104,2.896 0.438,0.281 2.281,1.188 2.802,1.083 true 1.01,3.885 1.594,3.677 true 1.708,3.573 1.188,2.833 1.188,2.833 1.052,2.833 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false C 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 0.802,3.813 1,4.01 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b 0.646,2.76 1.073,2.99 0.427,0.229 10 false GPS1 1.844,2.677 2,2.875 0.156,0.198 10 false D
*a Front view of wire harness connector
(to Telephone Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 - D-2 (GPS1) Always Below 1 Ω
C-2a - D-2a Always Below 1 Ω
C-2 or D-2 (GPS1) - Body ground Always 10 kΩ or higher
C-2a or D-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - TELEMATICS TRANSCEIVER [DATA COMMUNICATION MODULE (DCM)])
a.

Disconnect the H81 No. 2 antenna cord sub-assembly connector from the instrument panel wire.


b.

Disconnect the H82 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H81-2 (GPS1) - H82-1 (GPS2) Always Below 1 Ω
H81-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TELEPHONE ANTENNA ASSEMBLY
a.

Replace the telephone antenna assembly with a new or known good one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL



c.

Recheck for DTCs and check that no DTCs are output.

OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

6.REPLACE TELEMATICS TRANSCEIVER
6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT