Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › 2016.08–2021.06
RM27T0E _56 Audio / Visual / Telematics _056796 TELEMATICS _0277431 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B15C4  SRS Communication Error  


DESCRIPTION

If the telematics transceiver detects an error in communication between itself and the airbag sensor assembly as a result of a self check, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15C4 SRS Communication Error The telematics transceiver detects an error in signals from the airbag sensor assembly when ignition switch is ON.
·

Telematics transceiver

·

Center airbag sensor assembly

·

Wire harness or connector

·

Airbag system



WIRING DIAGRAM

E342824E03
1.208,0.833 1.823,1.031 0.615,0.198 10 false GSW3 5.531,0.854 6.146,1.052 0.615,0.198 10 false GSW 1.75,0.729 2.063,0.927 0.313,0.198 10 false 24 5.26,0.729 5.573,0.927 0.313,0.198 10 false 24 0.917,1.406 1.313,1.604 0.396,0.198 10 false G1 5.49,1.406 5.885,1.604 0.396,0.198 10 false G187 0.917,1.583 3.052,1.896 2.135,0.313 10 false Center Airbag Sensor Assembly 5.5,1.583 7.125,1.813 1.625,0.229 10 false Telematics Transceiver

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION

·

This vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.CHECK DTC (AIRBAG SYSTEM)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and wait for 20 seconds.


d.

Turn the GTS on.


e.

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.CHECK TELEMATICS TRANSCEIVER

B

2.CHECK TELEMATICS TRANSCEIVER
a.
B240640C18
2.354,1.25 2.563,1.698 2.563,1.698 2.688,1.698 false 0.125,0.125 0.396,0.385 0.271,0.26 10 false *a 2.729,1.625 3.177,1.906 0.448,0.281 10 false GSW 0.208,4.031 0.646,4.292 0.438,0.26 10 false GND 0.167,2.26 0.438,2.521 0.271,0.26 10 false *b
*a Component with harness connected
(Telematics Transceiver)
*b Waveform


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
24 (GSW) - Body ground Ignition switch ON Pulse generation (Refer to waveform)


Reference Waveform:
Item Condition
Tester connection G187-24 (GSW) - Body ground
Tool setting 5.0 V/DIV., 20 ms/DIV.
Vehicle condition Ignition switch ON



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEMATICS TRANSCEIVER

NG

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - CENTER AIRBAG SENSOR ASSEMBLY)
3.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - CENTER AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the G187 telematics transceiver connector.


b.

Disconnect the G1 center airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G187-24 (GSW) - G1-24 (GSW3) Always Below 1 Ω
G187-24 (GSW) or G1-24 (GSW3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR