Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2016.08–2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Stereo Component Amplifier and Telematics Transceiver  


DESCRIPTION

This telematics transceiver sends a mute signal to the stereo component amplifier assembly. The stereo component amplifier assembly controls the volume according to the mute signal from the telematics transceiver.

If there is an open in the circuit, noise can be heard from the speakers when changing the sound source.

If there is a short in the circuit, even though the stereo component amplifier assembly is functioning normally, no sound or only an extremely faint sound can be heard.

WIRING DIAGRAM

E245681E95
1.5,0.917 1.927,1.083 0.427,0.167 10 false TMUT 5.25,0.917 5.917,1.115 0.667,0.198 10 false MUTE 2.01,0.781 2.344,1.01 0.333,0.229 10 false 24 5,0.792 5.229,0.979 0.229,0.188 10 false 17 0.896,1.49 1.302,1.646 0.406,0.156 10 false H63 5.073,1.479 5.531,1.656 0.458,0.177 10 false G187 5.073,1.635 6.76,1.938 1.688,0.302 10 false Telematics Transceiver 0.896,1.646 2.125,1.979 1.229,0.333 10 false Stereo Component Amplifier Assembly

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E283621C05
0.198,0.865 0.688,1.125 0.49,0.26 1.042,0.354 1.292,0.354 1.292,0.354 1.458,1.188 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.281,0.906 0.677,1.104 0.396,0.198 10 false G187 0.615,0.271 1.177,0.469 0.563,0.198 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G187-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
3.5 V or higher → Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the H63 stereo component amplifier assembly connector.


b.

Disconnect the G187 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H63-24 (TMUT) - G187-17 (MUTE) Always Below 1 Ω
H63-24 (TMUT) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK STEREO COMPONENT AMPLIFIER ASSEMBLY
a.

Reconnect the stereo component amplifier assembly connector.


b.
E176650C32
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 false 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.563,0.771 1.906,0.969 0.344,0.198 10 false G187
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G187-17 (MUTE) - Body ground Ignition switch ACC 3.5 V or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY