Home › Engine / Hybrid System › 1GD-FTV (FUEL) › FUEL INJECTOR › 2016.08–2018.06
RM27T0E _51 Engine / Hybrid System _053670 1GD-FTV FUEL _0260590 FUEL INJECTOR A

1GD-FTV FUEL  FUEL INJECTOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the parts in the following chart (A), replace the No. 1 injection pipe subassembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly with new ones.

Replaced Parts (A) Pipes Requiring New Replacement
Injector assembly (including shuffling the injector assemblies between the cylinders)
·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly


Supply pump assembly Fuel inlet pipe sub-assembly
·

Common rail assembly

·

Cylinder block sub-assembly

·

Cylinder head sub-assembly

·

Cylinder head gasket

·

Timing chain case assembly


·

No. 1 injection pipe sub-assembly

·

No. 2 injection pipe sub-assembly

·

Fuel inlet pipe sub-assembly



·

After removing the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and/or fuel inlet pipe sub-assembly, clean them with a brush and compressed air.

·

The injector assembly is a precision instrument. Do not use the injector assembly if it is struck or dropped.

·

Make sure foreign matter does not enter the fuel path.



PROCEDURE

Hide 23682 1.INSTALL NOZZLE HOLDER GASKET

a.

Install 4 new nozzle holder gaskets to the cylinder head cover sub-assembly.


Hide 23670 2.TEMPORARILY INSTALL INJECTOR ASSEMBLY

HINT:

Before installing the injector assembly, check for carbon, foreign matter, etc. on the seal surfaces of the cylinder head sub-assembly and injector assembly. If there is foreign matter, remove it before installing the injector assembly.


a.

Install 4 new injection nozzle seats to the cylinder head sub-assembly.


b.

Apply a light coat of engine oil to the O-ring on each injector assembly.


c.
A344927E01
1.627,1.021 1.159,1.021 false 0.963,0.943 1.135,1.097 0.172,0.154 10 *1

Install a new O-ring to each injector assembly.

Text in Illustration
*1 O-Ring


d.

Install the 4 injector assemblies to the cylinder head sub-assembly.

NOTICE:

Fit the injector assembly to the injection nozzle seats.



e.
A344928E02
2.635,0.594 2.635,0.927 2.635,0.927 2.833,0.927 true 2.875,0.833 3.135,1.042 0.26,0.208 10 true *1

Install the nozzle holder clamps and washers as shown in the illustration.

Text in Illustration
*1 Washer

NOTICE:

Pay attention to the mounting orientation (beveled edge) of the washer.



f.

Temporarily install the nozzle holder clamp bolts.

NOTICE:

When temporarily installing the nozzle holder clamp bolt to the No. 1 nozzle holder clamp, make sure that the bolt and clamp are not at an angle.


HINT:

Apply a light coat of engine oil to the threads of the nozzle holder clamp bolts.



Hide 3.TEMPORARILY INSTALL NO. 1 AND NO. 2 INJECTION PIPE SUBASSEMBLY

a.

Temporarily install the 2 No. 2 injection pipe sub-assemblies 4 union nuts.


b.

Temporarily install the 2 No. 1 injection pipe sub-assemblies 4 union nuts.


Hide 23670 4.TIGHTEN INJECTOR ASSEMBLY

a.

Tighten the 4 nozzle holder clamp bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 5.TIGHTEN NO. 1 AND NO. 2 INJECTION PIPE SUB-ASSEMBLY

a.

With Common Rail Side Number Mark (24N):

i.
A439100C01
1.271,2.844 1.271,2.615 1.271,2.615 1.625,2.469 true 1.177,2.854 1.49,3.01 0.313,0.156 10 false *a
*a Number Mark (24N)


Make sure that the "24N" mark faces the common rail side of the injection pipe at the position shown in the illustration.

NOTICE:

Check for the number mark and tighten the parts to the specified tightening torque.



ii.
A347062C01
1.219,1.458 1.375,1.458 1.375,1.458 1.563,1.688 true 2.26,0.708 2.604,0.896 0.344,0.188 10 true *a 0.938,1.365 1.344,1.563 0.406,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Using SST, tighten the No. 1 and No. 2 injection pipe sub-assemblies 8 union nuts.

SST
09245-11010  

Torque:
Specified tightening torque : 24 N*m (245 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 18.8 N*m (192 kgf*cm, 14 ft.*lbf)





b.
A347062C01
1.219,1.458 1.375,1.458 1.375,1.458 1.563,1.688 true 2.26,0.708 2.604,0.896 0.344,0.188 10 true *a 0.938,1.365 1.344,1.563 0.406,0.198 10 true SST
*a Torque Wrench Fulcrum Length


Without Common Rail Side Number Mark (24N):

Using SST, tighten the No. 1 and No. 2 injection pipe sub-assemblies 8 union nuts.

SST
09245-11010  

Torque:
Specified tightening torque : 40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using SST (fulcrum length of 50 mm (1.97 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 31 N*m (316 kgf*cm, 23 ft.*lbf)




Hide 23760 6.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

a.
A339110E01
3.146,0.208 3.302,0.406 0.156,0.198 10 true 1 2.521,0.104 2.677,0.302 0.156,0.198 10 true 2 1.865,0.094 2.021,0.292 0.156,0.198 10 true 3 0.729,0.083 0.885,0.281 0.156,0.198 10 true 4 0.333,0.656 0.49,0.854 0.156,0.198 10 true 5

Temporarily install the nozzle leakage pipe assembly and 4 new gaskets with the 4 union bolts and bolt.


b.

Tighten the 4 union bolts and bolt in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the No. 5 fuel hose to the nozzle leakage pipe assembly.


Hide 7.INSTALL HARNESS BRACKET

a.

Install the harness bracket with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 8.INSTALL WIRING HARNESS CLAMP BRACKET

a.

Install the wiring harness clamp bracket with bolt to the cylinder head cover sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the pressure discharge valve connector to the common rail assembly.


Hide 25800 10.INSTALL EGR COOLER ASSEMBLY

Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected. (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION)


Hide 12.PERFORM REGISTRATION

a.

Perform registration of injector compensation codes. (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION)


b.

Perform registration of pilot quantity learning. (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION)