Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System) › from 2017.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) J

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  ECO Switch Circuit  


DESCRIPTION

When the ECO mode switch is turned on, the air conditioning amplifier assembly receives an ECO mode switch ON signal and controls the air conditioning to enhance fuel efficiency.

WIRING DIAGRAM

E381166E01
4.375,1.74 4.833,1.938 0.458,0.198 10 false G24 4.375,1.917 6.719,2.313 2.344,0.396 10 false Air Conditioning Amplifier Assembly 2.229,1.833 2.688,2.031 0.458,0.198 10 false G303 2.24,1.99 3.708,2.354 1.469,0.365 10 false Shift Position Indicator 0.979,1.854 2.177,2.083 1.198,0.229 10 false ECO Mode Switch 3,0.563 3.458,0.76 0.458,0.198 10 false ECU 3.177,1.198 3.635,1.396 0.458,0.198 10 false E 3.427,0.563 3.885,0.76 0.458,0.198 10 false 14 3.458,1.198 3.917,1.396 0.458,0.198 10 false 18 5.031,0.667 5.49,0.865 0.458,0.198 10 false ECOS 4.729,0.563 5.188,0.76 0.458,0.198 10 false 18

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Read the Data List according to the display on the GTS.


Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ECO Switch ECO mode switch / ON or OFF ON: ECO mode switch on
OFF: ECO mode switch off
-

OK:

Combination switch assembly (ECO mode switch) condition displayed on the GTS changes with the actual switch operation.


Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ECO MODE SWITCH
2.INSPECT ECO MODE SWITCH

b.

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - AIR CONDITIONING AMPLIFIER ASSEMBLY AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (SHIFT POSITION INDICATOR - AIR CONDITIONING AMPLIFIER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G24 air conditioning amplifier assembly connector.


b.

Disconnect the G303 shift position indicator connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G303-14 (ECU) - G24-18 (ECOS) Always Below 1 Ω
G303-18 (E) - Body ground Always Below 1 Ω
G303-14 (ECU) or G24-18 (ECOS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK SHIFT POSITION INDICATOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SHIFT POSITION INDICATOR
a.

Replace the shift position indicator with a known good one (See page Vehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Automatic Transmission)>DISASSEMBLY).


b.

Check that the malfunction disappears.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (SHIFT POSITION INDICATOR WAS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY