Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0405  Exhaust Gas Recirculation Sensor "A" Circuit Low  P0406  Exhaust Gas Recirculation Sensor "A" Circuit High  


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

P0405
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic).
·

Open or short in EGR valve position sensor circuit

·

EGR valve position sensor

·

ECM



P0406
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Ignition switch ON for 5 seconds EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic).
·

Open or short in EGR valve position sensor circuit

·

EGR valve position sensor

·

ECM



MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM

A221592E01
0.584,3.011 2.379,3.196 1.795,0.185 10 EGR Valve Position Sensor 0.584,2.822 0.879,2.985 0.295,0.163 10 C86 1.646,0.958 1.902,1.121 0.257,0.163 10 VC 1.47,1.533 1.868,1.690 0.397,0.158 10 EGLS 1.653,2.072 1.864,2.242 0.211,0.170 10 E2 2.003,0.986 2.131,1.139 0.128,0.152 10 1 2.017,2.079 2.145,2.232 0.128,0.152 10 2 2.003,1.547 2.131,1.699 0.128,0.152 10 3 5.695,0.944 6.111,1.107 0.416,0.163 10 VCEG 5.681,1.519 6.078,1.676 0.397,0.158 10 EGLS 5.681,2.058 6.086,2.228 0.406,0.170 10 EEGL 5.414,0.993 5.591,1.146 0.177,0.152 10 13 5.421,2.086 5.605,2.239 0.184,0.152 10 14 5.463,1.554 5.591,1.706 0.128,0.152 10 4 6.045,2.843 6.353,3.006 0.309,0.163 10 C91 6.045,2.99 6.409,3.153 0.364,0.163 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)
a.
U169089E02
1.479,2.156 1.281,2.521 true 1.729,2.156 1.927,2.531 true 0.771,2.052 1.146,2.281 0.375,0.229 10 false C86 1.938,2.552 2.177,2.729 0.24,0.177 10 false E2 1.083,2.531 1.365,2.708 0.281,0.177 10 false VC 0.24,1.052 0.469,1.24 0.229,0.188 10 false *a

Disconnect the EGR valve position sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C86-1 (VC) - C86-2 (E2) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to EGR valve position sensor)


c.

Reconnect the electric vacuum regulating valve assembly connector.



OK

2.INSPECT EGR VALVE POSITION SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
2.INSPECT EGR VALVE POSITION SENSOR
a.

Inspect the EGR valve position sensor (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)

NG

5.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
a.

Disconnect the EGR valve position sensor connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance of the wire harness side connectors.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
86-1 (VC) - C91-13 (VCEG) Always Below 1 Ω
C86-3 (EGLS) - C91-4 (EGLS) Always Below 1 Ω
C86-2 (E2) - C91-14 (EEGL) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
86-1 (VC) or C91-13 (VCEG) - Body ground Always 10 kΩ or higher
C86-3 (EGLS) or C91-4 (EGLS) - Body ground Always 10 kΩ or higher



d.

Reconnect the electric vacuum regulating valve assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
a.

Replace the electric EGR control valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch to ON for 5 seconds or more.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Confirm that the DTC is not output again.



NEXT

END