Home › Engine / Hybrid System › 1KD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053659 1KD-FTV ENGINE CONTROL _0260458 ECD SYSTEM C

1KD-FTV ENGINE CONTROL  ECD SYSTEM  P0489  Exhaust Gas Recirculation Control Circuit Low  P0490  Exhaust Gas Recirculation Control Circuit High  


DESCRIPTION

The EGR system recirculates exhaust gases in a way that suits every driving condition. The recirculated gas mixes with intake air. Therefore, the EGR system can slow combustion speed and keep the combustion temperature down. This helps reduce NOx emission.

In order to increase EGR circulation efficiency, the ECM adjusts the lift amount of the EGR valve and the throttle valve angle.

P0489
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
5 seconds after engine is started Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic).
·

Electric vacuum regulating valve assembly

·

Open or short in electric vacuum regulating valve assembly circuit

·

ECM



P0490
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
5 seconds after engine is started Open or short in electric vacuum regulating valve assembly circuit for 5 seconds or more (1 trip detection logic).
·

Electric vacuum regulating valve assembly

·

Open or short in electric vacuum regulating valve assembly circuit

·

ECM



Related Data List
DTC No. Data List
P0489
·

Actual EGR Valve Pos.

·

Target EGR Position


P0490

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



PROCEDURE

1.INSPECT ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
a.

Inspect the electric vacuum regulating valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>INSPECTION).



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

5.REPLACE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
U169111E02
0.167,0.052 0.375,0.281 0.208,0.229 10 false *a 0.573,0.917 0.865,1.083 0.292,0.167 10 false C76

Disconnect the electric vacuum regulating valve assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C76-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to electric vacuum regulating valve assembly)


c.

Reconnect the electric vacuum regulating valve assembly connector.



OK

3.CHECK HARNESS AND CONNECTOR (ELECTRIC VACUUM REGULATING VALVE ASSEMBLY - ECM)

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
3.CHECK HARNESS AND CONNECTOR (ELECTRIC VACUUM REGULATING VALVE ASSEMBLY - ECM)
a.

Disconnect the electric vacuum regulating valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
C76-2 - C93-9 (EGR) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
C76-2 or C93-9 (EGR) - Body ground Always 10 kΩ or higher



d.

Reconnect the electric vacuum regulating valve assembly connector.


e.

Reconnect the ECM connector.



OK

4.REPLACE ECM

NG

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPLACE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY
a.

Replace the electric vacuum regulating valve assembly (See page Engine / Hybrid System>1KD-FTV (EMISSION CONTROL)>EGR VALVE>REMOVAL).



NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.

HINT:

If the voltage at the electric vacuum regulating valve assembly connector is not 11 to 14 V, repair or replace the harness and connector between the electric vacuum regulating valve assembly and the EFI relay (including the EFI No. 2 fuse).




NEXT

7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the intelligent tester to the DLC3.



c.

Turn the ignition switch off for 30 seconds or more.


d.

Start the engine.


e.

Idle the engine for 5 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / DTC.


g.

Confirm that the DTC is not output again.



NEXT

END