Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › 2017.08–2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area

*1: w/ Entry and Start System

*2: except 2TR-FE

*3: for 2TR-FE

*4: w/ Tire Pressure Warning System

*5: for LED Headlight

Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus wire

·

Short in CAN branch wire

·

Central gateway ECU (network gateway ECU)

·

ECM

·

Air conditioning amplifier assembly

·

4 wheel drive control ECU (4WD control ECU)

·

Certification ECU (smart key ECU assembly)*1

·

Power steering ECU assembly

·

Master cylinder solenoid (skid control ECU)*2

·

Brake actuator assembly (skid control ECU)*3

·

Airbag sensor assembly

·

Steering sensor

·

Combination meter assembly

·

Tire pressure warning ECU and receiver*4

·

Main body ECU (multiplex network body ECU)

·

No. 1 headlight ECU sub-assembly LH*5

·

No. 2 CAN junction connector

·

No. 6 CAN junction connector



WIRING DIAGRAM

C402011E01
1.333,0.458 1.948,0.656 0.615,0.198 10 false G184 1.333,0.865 1.948,1.063 0.615,0.198 10 false G184 1.771,0.865 2.385,1.063 0.615,0.198 10 false G58 1.781,0.458 2.396,0.656 0.615,0.198 10 false G58 2.146,0.458 2.76,0.656 0.615,0.198 10 false G181 2.146,0.854 2.76,1.052 0.615,0.198 10 false G181 2.563,0.844 3.177,1.042 0.615,0.198 10 false G56 2.542,0.458 3.156,0.656 0.615,0.198 10 false G56 2.969,0.469 3.583,0.667 0.615,0.198 10 false G56 2.979,0.854 3.594,1.052 0.615,0.198 10 false G56 2.938,0.667 3.552,0.865 0.615,0.198 10 false 25*5 2.948,0.25 3.563,0.448 0.615,0.198 10 false 31*5 2.594,0.25 3.208,0.448 0.615,0.198 10 false 32*4 2.563,0.646 3.177,0.844 0.615,0.198 10 false 31*4 2.177,0.667 2.792,0.865 0.615,0.198 10 false 14*3 2.156,0.24 2.771,0.438 0.615,0.198 10 false 13*3 1.729,0.24 2.344,0.438 0.615,0.198 10 false 35*2 1.781,0.667 2.396,0.865 0.615,0.198 10 false 36*2 1.385,0.646 2,0.844 0.615,0.198 10 false 28*1 1.365,0.24 1.979,0.438 0.615,0.198 10 false 17*1 3.531,0.365 4.146,0.563 0.615,0.198 10 false 10 3.552,0.729 4.167,0.927 0.615,0.198 10 false 20 0.875,0.979 1.49,1.177 0.615,0.198 10 false CANL 0.875,0.354 1.49,0.552 0.615,0.198 10 false CANH 0.604,1.281 1.219,1.479 0.615,0.198 10 false ECM 4.292,0.333 4.906,0.531 0.615,0.198 10 false 6 4.313,0.729 4.927,0.927 0.615,0.198 10 false 16 5.052,1.073 5.667,1.271 0.615,0.198 10 false G229 5.094,1.26 7.031,1.688 1.938,0.427 10 false Central Gateway ECU (Network Gateway ECU) 5.677,0.438 6.292,0.635 0.615,0.198 10 false CA4H 5.708,0.833 6.323,1.031 0.615,0.198 10 false CA4L 5.406,0.323 6.021,0.521 0.615,0.198 10 false 18 5.448,0.729 6.063,0.927 0.615,0.198 10 false 17 0.125,2.781 0.74,2.979 0.615,0.198 10 false G215 0.135,2.969 1.698,3.344 1.563,0.375 10 false Certification ECU (Smart Key ECU Assembly)*6 0.833,2.281 1.448,2.479 0.615,0.198 10 false CANH 0.865,2.688 1.479,2.885 0.615,0.198 10 false CANL 1.365,2.552 1.979,2.75 0.615,0.198 10 false 8 1.375,2.146 1.99,2.344 0.615,0.198 10 false 7 3.542,2.167 4.156,2.365 0.615,0.198 10 false 3 3.448,2.552 4.063,2.75 0.615,0.198 10 false 13 4.292,2.563 4.906,2.76 0.615,0.198 10 false 12 5.448,2.177 6.063,2.375 0.615,0.198 10 false 20 4.313,2.135 4.927,2.333 0.615,0.198 10 false 2 5.427,2.563 6.042,2.76 0.615,0.198 10 false 40 5.677,2.313 6.292,2.51 0.615,0.198 10 false CANH 5.688,2.677 6.302,2.875 0.615,0.198 10 false CANL 5.25,3.031 6.969,3.385 1.719,0.354 10 false 4 Wheel Drive Control ECU (4WD Control ECU) 5.229,2.844 5.844,3.042 0.615,0.198 10 false G53 5.438,4.229 6.052,4.427 0.615,0.198 10 false 10 5.51,3.833 6.125,4.031 0.615,0.198 10 false 9 5.708,4.354 6.323,4.552 0.615,0.198 10 false CANL 5.677,3.958 6.292,4.156 0.615,0.198 10 false CANH 5.281,4.479 5.896,4.677 0.615,0.198 10 false R41 5.219,4.677 6.938,5.083 1.719,0.406 10 false Tire Pressure Warning ECU and Receiver*8 3.469,3.823 4.083,4.021 0.615,0.198 10 false 4*7 3.385,4.229 4,4.427 0.615,0.198 10 false 14*7 4.292,3.844 4.906,4.042 0.615,0.198 10 false 5*7 4.271,4.208 4.885,4.406 0.615,0.198 10 false 15*7 1.333,3.833 1.948,4.031 0.615,0.198 10 false 24 1.323,4.219 1.938,4.417 0.615,0.198 10 false 23 0.115,4.5 0.729,4.698 0.615,0.198 10 false A102 0.125,4.677 1.49,5.031 1.365,0.354 10 false No. 1 Headlight ECU Sub-assembly LH*9 0.885,3.948 1.5,4.146 0.615,0.198 10 false CANH 0.896,4.354 1.51,4.552 0.615,0.198 10 false CANL 0.146,6.146 0.76,6.344 0.615,0.198 10 false G46 0.156,6.313 2.583,6.698 2.427,0.385 10 false Power Steering ECU Assembly 0.854,5.625 1.469,5.823 0.615,0.198 10 false CANH 0.875,6.021 1.49,6.219 0.615,0.198 10 false CANL 1.365,5.5 1.979,5.698 0.615,0.198 10 false 1 1.354,5.896 1.969,6.094 0.615,0.198 10 false 2 3.552,5.51 4.167,5.708 0.615,0.198 10 false 8 3.49,5.896 4.104,6.094 0.615,0.198 10 false 18 4.313,5.5 4.927,5.698 0.615,0.198 10 false 7 4.292,5.885 4.906,6.083 0.615,0.198 10 false 17 5.438,5.49 6.052,5.688 0.615,0.198 10 false 11 5.427,5.896 6.042,6.094 0.615,0.198 10 false 12 5.698,5.615 6.313,5.813 0.615,0.198 10 false CANH 5.688,6.031 6.302,6.229 0.615,0.198 10 false CANL 5.323,6.313 6.958,6.698 1.635,0.385 10 false Air Conditioning Amplifier Assembly 5.313,6.167 5.927,6.365 0.615,0.198 10 false G25 4.302,7 4.917,7.198 0.615,0.198 10 false 9 4.292,7.396 4.906,7.594 0.615,0.198 10 false 19 5.25,7.719 5.865,7.917 0.615,0.198 10 false A6 5.219,7.885 6.854,8.24 1.635,0.354 10 false Brake Actuator Assembly (Skid Control ECU)*3 5.688,7.125 6.302,7.323 0.615,0.198 10 false CANH 5.688,7.51 6.302,7.708 0.615,0.198 10 false CANL 5.438,7 6.052,7.198 0.615,0.198 10 false 25 5.438,7.375 6.052,7.573 0.615,0.198 10 false 14 3.208,7.708 3.823,7.906 0.615,0.198 10 false G290 3.229,7.906 4.469,8.271 1.24,0.365 10 false No. 6 CAN Junction Connector 0.063,6.75 1.427,6.979 1.365,0.229 10 false *1: for 1GD-FTV 1.146,6.75 2.51,6.979 1.365,0.229 10 false *2: for 1KD-FTV 2.26,6.74 3.625,6.969 1.365,0.229 10 false *3: for 2TR-FE 0.063,7.052 2.781,7.406 2.719,0.354 10 false *4: for 1GR-FE with Manual Transmission 0.083,7.354 2.135,7.698 2.052,0.344 10 false *5: for 1GR-FE with Automatic Transmission 0.094,7.875 1.99,8.229 1.896,0.354 10 false *6: w/ Entry and Start System 0.052,8.177 1.24,8.417 1.188,0.24 10 false *7: for RHD 0.115,8.458 2.448,8.771 2.333,0.313 10 false *8: w/ Tire Pressure Warning System 2.531,8.479 4.844,8.667 2.313,0.188 10 false *9: for LED Headlight 3.531,7.01 4.146,7.208 0.615,0.198 10 false 1 3.479,7.385 4.094,7.583 0.615,0.198 10 false 11

C382807E06
3.25,0.438 3.406,0.635 0.156,0.198 10 false 1 3.188,0.854 3.417,1.063 0.229,0.208 10 false 11 3.958,0.438 4.115,0.635 0.156,0.198 10 false 2 3.917,0.823 4.146,1.031 0.229,0.208 10 false 12 5.698,0.469 5.854,0.667 0.156,0.198 10 false 3 5.698,0.833 5.854,1.031 0.156,0.198 10 false 2 5.917,0.563 6.438,0.781 0.521,0.219 10 false CANH 5.917,0.958 6.438,1.177 0.521,0.219 10 false CANL 5.26,1.135 5.781,1.354 0.521,0.219 10 false G205 5.292,1.292 6.906,1.75 1.615,0.458 10 false Steering Sensor 3.948,2.198 4.104,2.396 0.156,0.198 10 false 3 3.938,2.625 4.156,2.823 0.219,0.198 10 false 13 5.625,2.24 5.875,2.438 0.25,0.198 10 false 13 5.635,2.646 5.885,2.865 0.25,0.219 10 false 22 5.927,2.344 6.448,2.563 0.521,0.219 10 false CANH 5.948,2.719 6.469,2.938 0.521,0.219 10 false CANL 5.406,2.938 5.927,3.156 0.521,0.219 10 false G1 5.406,3.104 7.052,3.344 1.646,0.24 10 false Airbag Sensor Assembly 3.104,2.219 3.417,2.438 0.313,0.219 10 false 7*2 3.042,2.667 3.396,2.938 0.354,0.271 10 false 17*2 0.229,2.969 0.521,3.167 0.292,0.198 10 false R41 0.229,3.146 1.958,3.521 1.729,0.375 10 false Tire Pressure Warning ECU and Receiver*1 0.844,2.375 1.365,2.594 0.521,0.219 10 false CANH 0.865,2.75 1.385,2.969 0.521,0.219 10 false CANL 1.344,2.24 1.5,2.438 0.156,0.198 10 false 9 1.344,2.656 1.594,2.854 0.25,0.198 10 false 10 0.219,4.729 0.51,4.927 0.292,0.198 10 false A7 0.208,4.917 1.802,5.323 1.594,0.406 10 false Master Cylinder Solenoid (Skid Control ECU)*3 0.813,4.156 1.333,4.375 0.521,0.219 10 false CANH 0.823,4.531 1.344,4.75 0.521,0.219 10 false CANL 1.354,4.01 1.708,4.25 0.354,0.24 10 false 11 1.354,4.427 1.708,4.667 0.354,0.24 10 false 25 3.156,4.031 3.51,4.271 0.354,0.24 10 false 10 3.156,4.438 3.51,4.677 0.354,0.24 10 false 20 3.958,4.031 4.313,4.271 0.354,0.24 10 false 9 3.938,4.417 4.292,4.656 0.354,0.24 10 false 19 3.927,5.979 4.281,6.219 0.354,0.24 10 false 8 3.938,6.375 4.292,6.615 0.354,0.24 10 false 18 5.656,4.042 5.885,4.25 0.229,0.208 10 false 14 5.656,4.448 5.885,4.656 0.229,0.208 10 false 13 5.938,4.125 6.458,4.344 0.521,0.219 10 false CANH 5.958,4.552 6.479,4.771 0.521,0.219 10 false CANL 5.354,4.75 5.875,4.969 0.521,0.219 10 false G218 5.354,4.906 7.031,5.406 1.677,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.458,6.75 5.979,6.969 0.521,0.219 10 false G304 5.479,6.896 6.646,7.375 1.167,0.479 10 false Combination Meter Assembly 5.938,5.948 6.458,6.167 0.521,0.219 10 false CANH 5.938,6.604 6.458,6.823 0.521,0.219 10 false CANL 5.656,6.365 5.885,6.573 0.229,0.208 10 false 39 5.667,5.969 5.896,6.177 0.229,0.208 10 false 40 2.979,6.677 3.5,6.896 0.521,0.219 10 false G286 3,6.844 4.313,7.292 1.313,0.448 10 false No. 2 CAN Junction Connector 0.198,7.625 3.167,7.906 2.969,0.281 10 false *1: w/ Tire Pressure Warning System 0.219,7.948 1.656,8.198 1.438,0.25 10 false *2: for LHD 0.208,8.24 1.708,8.49 1.5,0.25 10 false *3: except 2TR-FE 0.177,6.656 0.698,6.875 0.521,0.219 10 false A102 0.156,6.854 1.604,7.24 1.448,0.385 10 false No. 1 Headlight ECU Sub-assembly LH*4 3.052,6.01 3.406,6.25 0.354,0.24 10 false 4*2 2.99,6.365 3.344,6.604 0.354,0.24 10 false 14*2 0.219,8.552 1.719,8.802 1.5,0.25 10 false *4: for LED Headlight 0.802,6.115 1.323,6.333 0.521,0.219 10 false CANH 0.813,6.479 1.333,6.698 0.521,0.219 10 false CANL 1.344,5.979 1.698,6.219 0.354,0.24 10 false 24 1.354,6.406 1.708,6.646 0.354,0.24 10 false 23

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 6 CAN junction connector.

C349815C42
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 3.229,1.354 3.229,0.385 3.229,0.385 3.073,0.385 true 4.375,2.24 4.198,2.24 4.198,2.24 4.198,1.573 true 3.469,1.344 3.469,0.188 3.469,0.188 3.313,0.188 true 3.719,1.344 3.719,0.188 3.719,0.188 3.896,0.188 true 3.958,1.344 3.958,0.375 3.958,0.375 4.135,0.375 true 4.198,1.344 4.198,0.583 4.198,0.583 4.385,0.583 true 4.438,1.333 4.438,0.771 4.438,0.771 4.615,0.771 true 3.052,2.448 3.229,2.448 3.229,2.448 3.229,1.583 true 3.896,2.635 3.719,2.635 3.719,2.635 3.719,1.573 true 3.292,2.635 3.469,2.635 3.469,2.635 3.469,1.573 true 4.156,2.438 3.958,2.438 3.958,2.438 3.958,1.573 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 4.604,2 4.438,2 4.438,2 4.438,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 2.542,0.323 3.198,0.521 0.656,0.198 10 false CANH*e 1.656,1.344 2.25,1.552 0.594,0.208 10 false G290 2.771,0.115 3.427,0.313 0.656,0.198 10 false CANH*f 3.948,0.125 4.604,0.323 0.656,0.198 10 false CANH*g 4.208,0.313 4.865,0.51 0.656,0.198 10 false CANH*h 4.479,0.51 5.135,0.708 0.656,0.198 10 false CANH*i 4.677,0.708 5.333,0.906 0.656,0.198 10 false CANH*j 2.521,2.375 3.177,2.573 0.656,0.198 10 false CANL*e 2.771,2.573 3.427,2.771 0.656,0.198 10 false CANL*f 3.958,2.573 4.615,2.771 0.656,0.198 10 false CANL*g 4.219,2.375 4.875,2.573 0.656,0.198 10 false CANL*h 4.417,2.177 5.073,2.375 0.656,0.198 10 false CANL*i 4.667,1.948 5.323,2.146 0.656,0.198 10 false CANL*j 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*k 5.125,1.729 5.781,1.927 0.656,0.198 10 false CANL*k 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to 4 Wheel Drive Control ECU (4WD Control ECU) *d to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System)
*e to No. 1 Headlight ECU Sub-assembly LH (for RHD with LED Headlight) *f to Tire Pressure Warning ECU and Receiver (for RHD with Tire Pressure Warning System)
*g to Central Gateway ECU (Network Gateway ECU) *h to Air Conditioning Amplifier Assembly
*i to Power Steering ECU Assembly *j to Brake Actuator Assembly (Skid Control ECU) (for 2TR-FE)
*k to ECM - -



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: w/ Entry and Start System

*2: for RHD with LED Headlight

*3: for RHD with Tire Pressure Warning System

*4: for 2TR-FE

G290-1 (CANH) - G290-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
G290-2 (CANH) - G290-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher 4 Wheel drive control ECU (4WD control ECU)
G290-3 (CANH) - G290-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Certification ECU (smart key ECU assembly)*1
G290-4 (CANH) - G290-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 headlight ECU sub-assembly LH*2
G290-5 (CANH) - G290-15 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU and receiver*3
G290-6 (CANH) - G290-16 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Central gateway ECU (network gateway ECU)
G290-7 (CANH) - G290-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Air conditioning amplifier assembly
G290-8 (CANH) - G290-18 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Power steering ECU assembly
G290-9 (CANH) - G290-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Brake actuator assembly (skid control ECU)*4
G290-10 (CANH) - G290-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK A
NG (Central gateway ECU [network gateway ECU] CAN branch wire) B
NG (ECM CAN main wire) C
NG (No. 2 CAN junction connector CAN main wire) D
NG (Wire to ECU or sensor) E



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

2.CONNECT CONNECTOR

C

4.CONNECT CONNECTOR

D

6.CONNECT CONNECTOR

E

10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
2.CONNECT CONNECTOR
a.

Reconnect the G290 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)
a.
C368242C22
1.417,0.24 1.958,0.458 0.542,0.219 1.281,1.771 1.479,1.771 1.479,1.771 1.646,1.26 true 2.073,1.771 1.906,1.771 1.906,1.771 1.76,1.271 true 1.531,0.271 1.99,0.469 0.458,0.198 10 false G229 0.948,1.688 1.406,1.885 0.458,0.198 10 false CA4L 2.115,1.688 2.573,1.885 0.458,0.198 10 false CA4H 0.073,0.042 0.531,0.24 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-18 (CA4H) - G229-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 6 CAN JUNCTION CONNECTOR)

4.CONNECT CONNECTOR
a.

Reconnect the G290 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR SHORT IN CAN BUS WIRES (ECM - NO. 6 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT IN CAN BUS WIRES (ECM - NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the ECM connector.

C382811C02
0.896,0.333 1.271,0.563 0.375,0.229 2.552,0.365 2.927,0.594 0.375,0.229 4.083,0.375 4.49,0.604 0.406,0.229 5.698,0.354 6.104,0.583 0.406,0.229 0.615,2.458 0.448,2.458 0.448,2.458 0.75,1.76 true 1.01,2.281 0.844,2.281 0.844,2.281 0.958,1.792 true 0.635,0.563 0.771,0.563 0.771,0.563 0.75,1.688 true 2.844,2.458 2.677,2.458 2.677,2.458 3,1.802 true 3.094,2.135 2.927,2.135 2.927,2.135 3.094,1.813 true 4.24,2.115 4.375,2.115 4.375,2.115 4.542,1.427 true 4.344,2.313 4.479,2.313 4.479,2.313 4.667,1.417 true 5.24,2.479 5.375,2.479 5.375,2.479 5.458,1.688 true 6.042,2.271 5.875,2.271 5.875,2.271 5.479,1.531 true 0.115,0.063 0.427,0.26 0.313,0.198 10 false *a 0.938,0.365 1.25,0.563 0.313,0.198 10 false G56 2.604,0.406 2.917,0.604 0.313,0.198 10 false G58 4.135,0.417 4.542,0.625 0.406,0.208 10 false G181 5.75,0.396 6.156,0.604 0.406,0.208 10 false G184 0.667,2.385 1.885,2.635 1.219,0.25 10 false CANH*C, CANL*B 1.292,0.354 1.854,0.604 0.563,0.25 10 false *A 1.063,2.219 2.26,2.448 1.198,0.229 10 false CANH*B 2.969,0.396 3.531,0.646 0.563,0.25 10 false *D 0.073,0.49 0.635,0.74 0.563,0.25 10 false CANL*C 2.906,2.385 3.469,2.635 0.563,0.25 10 false CANH 3.135,2.063 3.625,2.281 0.49,0.219 10 false CANL 4.563,0.406 5.125,0.656 0.563,0.25 10 false *E 3.823,2.031 4.385,2.281 0.563,0.25 10 false CANH 3.958,2.24 4.521,2.49 0.563,0.25 10 false CANL 6.156,0.385 6.719,0.635 0.563,0.25 10 false *F 6.104,2.208 6.667,2.458 0.563,0.25 10 false CANH 4.844,2.396 5.406,2.646 0.563,0.25 10 false CANL
*A for 1GR-FE *B for Manual Transmission
*C for Automatic Transmission *D for 1KD-FTV
*E for 2TR-FE *F for 1GD-FTV
*a Front view of wire harness connector
(to ECM)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE with Manual Transmission
Tester Connection Condition Specified Condition
G56-32 (CANH) - G56-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1GR-FE with Automatic Transmission
Tester Connection Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1KD-FTV
Tester Connection Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 2TR-FE
Tester Connection Condition Specified Condition
G181-13 (CANH) - G181-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω

for 1GD-FTV
Tester Connection Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM - NO. 6 CAN JUNCTION CONNECTOR)

6.CONNECT CONNECTOR
a.

Reconnect the G290 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

C349815C43
1.604,1.281 2.01,1.563 0.406,0.281 2.583,2 2.74,2 2.74,2 2.74,1.573 true 2.99,1.344 2.99,0.583 2.99,0.583 2.844,0.583 true 2.75,1.354 2.75,0.792 2.75,0.792 2.604,0.792 true 4.375,2.24 4.198,2.24 4.198,2.24 4.198,1.573 true 3.958,1.344 3.958,0.375 3.958,0.375 4.135,0.375 true 4.198,1.344 4.198,0.583 4.198,0.583 4.385,0.583 true 4.438,1.333 4.438,0.771 4.438,0.771 4.615,0.771 true 4.156,2.438 3.958,2.438 3.958,2.438 3.958,1.573 true 2.813,2.24 2.979,2.24 2.979,2.24 2.979,1.573 true 4.604,2 4.438,2 4.438,2 4.438,1.573 true 4.688,1.354 4.938,1.031 4.938,1.031 5.115,1.031 true 5.063,1.802 4.896,1.802 4.896,1.802 4.677,1.521 true 2.49,1.406 2.25,0.969 2.25,0.969 2.104,0.969 true 2,1.854 2.156,1.854 2.156,1.854 2.51,1.531 true 3.219,1.354 3.219,0.344 3.219,0.344 3.073,0.344 true 3.042,2.49 3.208,2.49 3.208,2.49 3.208,1.563 true 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 2.052,0.729 2.708,0.927 0.656,0.198 10 false CANH*c 2.042,1.948 2.698,2.146 0.656,0.198 10 false CANL*c 2.25,2.167 2.906,2.365 0.656,0.198 10 false CANL*d 2.302,0.51 2.958,0.708 0.656,0.198 10 false CANH*d 1.656,1.344 2.25,1.552 0.594,0.208 10 false G286 4.208,0.313 4.865,0.51 0.656,0.198 10 false CANH*f 4.479,0.51 5.135,0.708 0.656,0.198 10 false CANH*g 4.677,0.708 5.333,0.906 0.656,0.198 10 false CANH*h 4.219,2.375 4.875,2.573 0.656,0.198 10 false CANL*f 4.406,2.167 5.063,2.365 0.656,0.198 10 false CANL*g 4.667,1.948 5.323,2.146 0.656,0.198 10 false CANL*h 5.167,0.969 5.823,1.167 0.656,0.198 10 false CANH*i 5.115,1.729 5.771,1.927 0.656,0.198 10 false CANL*i 1.563,0.885 2.219,1.083 0.656,0.198 10 false CANH*b 1.49,1.76 2.146,1.958 0.656,0.198 10 false CANL*b 2.521,0.271 3.177,0.469 0.656,0.198 10 false CANH*e 2.51,2.417 3.167,2.615 0.656,0.198 10 false CANL*e
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to Steering Sensor *d to Airbag Sensor Assembly
*e to No. 1 Headlight ECU Sub-assembly LH (for LHD with LED Headlight) *f to Tire Pressure Warning ECU and Receiver (for LHD with Tire Pressure Warning System)
*g to Combination Meter Assembly *h to Main Body ECU (Multiplex Network Body ECU)
*i to Master Cylinder Solenoid (Skid Control ECU) (except 2TR-FE) - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to

*1: for LHD with LED Headlight

*2: for LHD with Tire Pressure Warning System

*3: except 2TR-FE

G286-1 (CANH) - G286-11 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector
G286-2 (CANH) - G286-12 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Steering sensor
G286-3 (CANH) - G286-13 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Airbag sensor assembly
G286-4 (CANH) - G286-14 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher No. 1 headlight ECU sub-assembly LH*1
G286-7 (CANH) - G286-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Tire pressure warning ECU and receiver*2
G286-8 (CANH) - G286-18 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly
G286-9 (CANH) - G286-19 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Main body ECU (multiplex network body ECU)
G286-10 (CANH) - G286-20 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Master cylinder solenoid (skid control ECU)*3



Result:
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 6 CAN junction connector CAN main wire) C
NG (Wire to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

8.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 6 CAN JUNCTION CONNECTOR)

D

10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
8.CONNECT CONNECTOR
a.

Reconnect the G286 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
9.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)
a.
C369139C08
1.5,0.75 1.917,1 0.417,0.25 2.354,2.448 2.521,2.448 2.521,2.448 2.792,1.917 true 2.396,2.75 2.563,2.75 2.563,2.75 2.917,1.938 true 1.552,0.802 1.958,1 0.406,0.198 10 false G304 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.958,2.385 2.458,2.573 0.5,0.188 10 false CANL 1.958,2.656 2.458,2.844 0.5,0.188 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-40 (CANH) - G304-39 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 2 CAN JUNCTION CONNECTOR)

10.CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR)
a.
C368243C12
1.448,0.104 1.917,0.323 0.469,0.219 2.021,1.76 1.854,1.76 1.854,1.76 1.781,1.115 true 1.333,1.75 1.5,1.75 1.5,1.75 1.677,1.115 true 2.083,1.688 2.542,1.885 0.458,0.198 10 false CA4L 1.542,0.146 2,0.344 0.458,0.198 10 false G229 0.948,1.667 1.406,1.865 0.458,0.198 10 false CA4H 0.063,0.063 0.521,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Reconnect the wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G229-18 (CA4H) - G229-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.



Result:
Proceed to
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPLACE CORRESPONDING ECU OR SENSOR